ICW Elite User manual

If you have any questions please call Toll Free 1-800-558-4435
ICWUSA.com, Inc.
TITAN ELITE EASY-TO-WIRE CEILING MOUNT INSTALLATION - 12/12/17
DOUBLE ELITE CEILING MOUNT INSTALLATION
MAXIMUM LOAD CAPACITY: 30 LBS (13.6 KG)
DANGER!
• Installationwithatleasttwopersonsisrecommended
fortheELP6220series.
•Do notattempttoadjustthearmuntilallcomponents
aremounted(monitor,keyboard,etc.).
•Arm must be completely horizontal (extended)
beforeadjustingthearm’stension.Failuretodosowill
damagethearmandvoidthewarranty.
•NEVER loosen or remove any of the shoulder
bolts.Doingsowillcausethearmtoimmediately
comeapartwithtremendousforce,andcouldcause
seriousinjury(seescreen.
• IfequipmentrequiringACpowerismountedtothisunit,
haveacertiedelectricianinspecttheinstallation.
• Failuretoinstallthisunitaccordingtotheseinstructions
willvoidallICWwarranties.Ifinstalledincorrectly,ICW
isnotliableforanydamageorinjurycausedbytheunit.
The Elite arm contains high pressure
gas springs. The following cautions
MUST be observed to avoid serious injury.
Page1of3
To avoid damaging threads,
DO NOT use power tools to assemble
or adjust the arm. Use hand tools ONLY.
IMPORTANT
1. MOUNT SQUARE CEILING PLATE AND DROP POLE
Loosenthesetscrew
inceilingplatebefore
attachingextensionpipe.
2. ATTACH ARM TO DROP POLE
Checkthatsetscrew
isbackedoutenough
totighten.Fullythread
armontoextension
pipeandtighten.
NOTE: Thereisahole
foraspannerthatcanbe
usedtoaddextraleverage
fortighteningthethread.
AFTERarmisrmly
attached,tighten
setscrewwith5/32
hexkey.Onceset,
retightensetscrew.
WARNING:
DONOTloosenlower,
smallerscrewwithout
approvalfromICW.
Usingfour1/4x2”lagboltsprovidedinhardwarebag,
secureceilingplatetoasolidwoodsurfaceorceiling
joist.Usesquarepatternorinlinepattern.Besurethe
plateislevelanduseallfourbolts.
Itmaybeeasiertopre-installthecablingthrough
thedroppolebeforeinstallation.Ifyouchoosethis
method,runasufcientlengthofcablethroughthebase
centerholeorwiremanagementport.Youwillrequire
aminimumlengthof12”cablingfortheXT24droppole
and10”cablingfortheXT12droppole.Then, add
required additional length on both ends.Loosen
setscrewBEFOREattachingpipe.
Threadextensionpipe
fullyontoceilingplate,
thentightensetscrew.
Ensuredroppole
isverticallystraight.
SUGGESTION:
Setinnerpoleat
lowestpointbefore
movingintoits
permanentposition.
Toavoidunnecessary
visiblemarks
ondroppole.
Setscrew
Wiremanagementholes

TITAN ELITE EASY-TO-WIRE CEILING MOUNT INSTALLATION - 12/12/17
DOUBLE ELITE CEILING MOUNT INSTALLATION
6. REATTACH ARM COVERS
TOP COVERS: Reattachbyreplacingthetwo
6-32x1/4”atheadscrewsinthecenterof
thecoverusinga#2Phillipsheadscrewdriver.
CENTER COVER: Reattachbyreplacingthefour
10-24x3/4”atheadscrewsusinga#2Phillips
headscrewdriver.
END COVERS: Reattachbyreplacingthetwo10-24x
3/4”atheadscrewsusinga#2Phillipsheadscrewdriver.
AttachVESA
tomonitorusing
fourM4screws
inthehardware
bag.Mountthe
VESAassembly
byscrewingthe
knobthroughthe
railintotheVESA.
Usethesliderknobtoloosenthesliderto
adjusttheheightofthemonitorontheParalink.
Adjustthepivottensionoftheballbygently
andevenlytighteningorlooseningthefour
screwsonthebackoftheballVESA.
8. ATTACH MONITOR VESA TO MOUNT
Extendarmsstraightdownandremove
cableclipsrunallthecablesformonitor,
keyboardandmouseinthechannelin
theblackinnerarm.Reattachcableclips.
5. FEED CABLE THROUGH ARM
3. REMOVE ARM COVERS
CENTER AND
END COVERS:
Removethese
rstbyunscrewing
thetwo3/4”long
10-24athead
screwsusinga
#2Phillipshead
screwdriver.
CENTER
COVER
SHOULDER
BOLTS
(DO NOT
LOOSEN)
SHOULDER
BOLTS
(DO NOT
LOOSEN)
TOP COVERS:
Removethelongarm
coversbyunscrewing
thetwo1/4”long6-32
atheadscrewsinthe
centerofthecover
usinga#2Phillips
headscrewdriver.
Page2of3
FACTORY TORQUE
120 INCH POUNDS.
DO NOT LOOSEN.
NOTE: YOUMUST
LEAVESOMESLACK
INTHECABLESAT
THECENTERCOVER
TOALLOWFOR
ARMMOVEMENT.
7. REPLACE ARM COVERS
Beforereattaching
armcovers,slip
wiresthrough
endcoverport.
Reattach
blackplastic
bushingaround
exitingwires.
Replacecovers
ontheElite
sectionofthe
arm.DONOT
useapowertool
toinsertscrews.
4. FEED WIRE
THROUGH DROP POLE
Pullwiresoneatatime
throughthearm.Feedthe
largestwirerst,allowing
enoughslacksothearm
turnsfreely.
Feedtherst
wirethroughthe
extensionpipe
anddownthrough
therstjointand
outintotheblack
channelorthe
rstelitearm.
Feedthecablesbetweentheelitearms
throughthecenterframeandintothe
blackchannelofthesecondelitearm.
Repeatthesestepswiththeremainingcables.
CEILING CEILING

DOUBLE ELITE CEILING MOUNT INSTALLATION
TITAN ELITE EASY-TO-WIRE CEILING MOUNT INSTALLATION - 12/12/17
Page3of3
10. ATTACH KEYBOARD FLIP-UP TO DROP
Attachthetrayip-up
assemblytothedropusing
theprovidedathead
screwsand5/32hexkey.
9. MONITOR TILT, ROTATION & ADJUST MONITOR DEPTH
MONITOR
TILT & ROTATE
Gentlyhold
sidesofmonitor.
Tiltandrotateto
desiredposition
withballVESA.
ADJUST
MONITOR
DEPTH
Loosenthe
adjustment
knob,move
theParalink
forwardor
back,then
re-tighten
theknob.
Adjustment
Knob
9/16
socket
wrench
End
frame
11. ADJUST HORIZONTAL TILT ANGLE
Buttonheadbolt Setscrews
13. ADJUST ROTATION STOPS
Rotationlimitsforthe
armaresetbyplacing
stoppinsintheholes
whereyouwantthe
armtostop.Thestop
pinscanberemoved
andsetbyhand.
12. ADJUST ARM LIFTING CAPACITY
Extendtheupperarmstraightoutasshown
beforeadjustingthearm’sliftingcapacity.
Besureallequipmentismountedonthe
armbeforeadjusting.Adjustthearmclosestto
themonitorrst.Usethe3/16”T-handleprovided.
• Removelongtopcoverandfrontendcover.
• Insert9/16socketwrenchovernutinendframe.
• Frombeneatharm,slightlyloosencenterbolt
withprovidedhexkey.
• Tightensetscrewswithhexkeyuntilfootislevel,
thenretightencenterbolt.Checkforlevel.Repeat
ifnecessary.Ifcenterboltisnotretightened,
theElitefootcouldcomeloose.
• Replacearmcovers,asinscreens6and7.
Torque Chart- In/lbs 2/23/2016
Minimum torque values Monitor Mount
Arm
Base
Mount Arm Joint Paralink EV710 Ultra
021-021-021etilE
021-021021021etilE2T
Titan (T2) 120 120 120 - 120
02158021021021artlU
UL180 / UL182 120 120 - 85 -
MD Arm 140 - 120 - 120
3/16”
T-handle
Upper Arm
Lower Arm