ICW MD User manual

If you have any questions, please call 1-800-558-4435
MD ARM INSTALLATION INSTRUCTIONS
MD ARM INSTALLATION INSTRUCTIONS - rev 04/22/14 pjm
Page 1 of 3
ATTACH MD
WALL MOUNT
Locate a stud in a
wall you intend to
mount your arm on.
Mark the top hole,
drill 11/64 pilot hole
and insert an ICW
provided #14 screw
and tighten slightly.
Using a level, mark
the 3 lower holes and
drill pilot holes, insert
the last three #14
screws and with the
mount level, tighten
all screws securely.
Lift the wall
mount up to
the bottom
of the TMD
track, or lower
over the top
of the track if
easier. Slide
the clamp
plates into the
groove in the
TMD track.
Track
clamp
plates
Once the
wall plate is
at the height
that you
want it, use
the 5/32 hex
key to lock it
into place by
turning the
3 clamping
screws in
to place
clockwise.
Clamp
screws
ATTACH WALL PLATE TO TRACK
IF MOUNTING DIRECTLY TO WALL
IF MOUNTING TO WALL TRACK
REMOVE COVERS FROM MD ARM Using a Phillips head
screwdriver, remove the four
screws from the upper cover,
exposing the cable channel.
WARNING - PINCH POINT:
Keep fi ngers away from
the inner arm area where
the gas spring is located.
The lower cover can also
be removed by lowering the
arm into the down position,
removing the screws and
sliding the cover forward off
of the arm.
OR

MD ARM INSTALLATION INSTRUCTIONS - rev 04/22/14 pjm
Page 2 of 3
MD ARM INSTALLATION INSTRUCTIONS
ADJUST BALL VESA
TENSION & HEIGHT
Use the slider knob to
loosen the slider to adjust
the height of the monitor
on the Paralink.
Adjust the pivot tension
of the ball by gently and
evenly tightening or
loosening the four screws
on the back of the ball
VESA.
Slider Knob
Pivot tension
adjustment
screws
ATTACH VESA TO MONITOR
Attach VESA to
monitor using four
4mm screws in the
hardware bag.
ADJUST
PARALINK TILT
Adjust monitor to desired
position with ball VESA.
Tilt your monitor 50°
in any direction. Adjust
your monitor between
portrait and landscape
by rotating ball VESA.
Adjust monitor depth
by moving the paralink
forward or back then
tighting the depth
adjustment knob.
Depth
Adjustment
Knob
ATTACH THE THBV HANDLE
The THBV is attached
to the Paralink and
Quicklink by two
screws on the back of
the VESA plate.
Screw
to attach
handle.
Screw
to attach
handle.
ATTACH
PARALINK
TO MD ARM
Attach the Paralink to
MD arm using 3/8 bolt
assembly and 1” bearing
assembly provided. Insert
bolt assembly up through
ear at end of arm. Place 1”
bearing assembly over bolt
on top of ear. Place Paralink
over bolt and bearing and
turn bolt until Paralink is
secure and smoothly turns
against the bearing. Beauty cap
3/8 bolt
1” bearing

MD ARM INSTALLATION INSTRUCTIONS - rev 04/22/14 pjm
Page 3 of 3
MD ARM INSTALLATION INSTRUCTIONS
ATTACH FLIP UP
1.Remove screws from
drop extension using
5/32” hex key.
2.Align holes in keyboard
tray with screw holes in
drop extension.
3.Attach keyboard tray
using the provided
screws.
IF USING PARALINK KEYBOARD TRAY
IF USING ULTRA
KEYBOARD TRAY
ADJUST MD ARM RESISTANCE
Using the 3/16”
t - h a n d l e h e x
wrench provided,
turn the screw in the
MD arm clockwise
to lighten the arm’s
load resistance, or
counter-clockwise
to increase the load
resistance.
ATTACH COVERS TO MD ARM After lowering the arm to the
down position, slide on the
lower cover. Using a Phillips
head screwdriver (NOT
POWER TOOLS), reattach the
four screws attaching the lower
cover.
Attach the top cover by
reattaching the four top cover
screws using a Phillips head
screwdriver (NOT POWER
TOOLS).
WARNING - PINCH POINT:
Keep fi ngers away from the
inner arm area where the gas
spring is located.
OR
ATTACH QUICK DISCONNECT
1.Remove beauty cap on quick
disconnect block.
2.Remove screw using 3/16”
hex key.
3.Slide keyboard tray into quick
disconnect block.
4.Replace screw and tighten.
5.Replace beauty cap.
Beauty cap
Screw
ATTACH PARALINK KEYBOARD TO MONITOR
Attach the Paralink
Keyboard Mount to the
Monitor Mount by using
the 3/8-16 screw and lock
washer provided.