ICW T2 User manual

ICWUSA.com, Inc.
If you have any questions, please call 1-800-558-4435
T2 ARM INSTALLATION INSTRUCTIONS
T2 ARM INSTALLATION INSTRUCTIONS - rev 06/18/2012 mf
page 1
ATTACH WALL
PLATE TO WALL
Locate stud and mark top
hole, drill 11/64 pilot hole
and insert #14 screw and
tighten slightly. Using a
level, mark lower hole
and drill pilot hole, insert
#14 screw and, with
unit level, tighten both
screws. ICW supplies
#14 wood screws. If
installing onto metal
studs, you will need
to replace with proper
metal stud fasteners.
MANAGE CABLES THROUGH ARM
Disassemble arm like shown using
Chrome 5mm hex key. Feed your
computer monitor cords and any
other cords down through opening
in wall mount - passing through
bearing. Slip all cords through upper
arm, bearings and lower arm. When
running your cords through arm,
keep them all to one side of bolts
at arm joints. Pass cords through
slots in monitor mount base plate
and re-attach monitor mount to front
arm. Once all cords are ran through
the arm, reattach arms in the same
order as it was disassembled using
Chrome 5mm hex key.
Cable slots
Note: When measuring
for length of cords, be
sure to allow enough extra
cord to accommodate tilt
and rotation of monitor.
NOTE: CORDS CAN BE
DAMAGED IF JOINTS ARE
ROTATED MORE THAN
360 DEGREES.
Bearing
Wallmount
Paralink
WARNING: When
disassembling the
arms, the Chrome 5mm
hex key must be used.
If a smaller hex key is
used, the bold will strip.
ATTACH DESKMOUNT TO DESK
Please follow cable management
instructions before securing desk mount.
Drill a 3/8 hole through the
horizontal surface you intend to
mount to. Screw the 3/8 stud into
your desk mount as shown, the
stud is found in your hardware
bag.
Push the 3/8 stud on desk mount
through the hole in the desk and
slip the large mounting washer
over the stud from underneath
and secure in place with the 3/8
nylock nut.
Remember to detach
desk mount and feed
cords down through
the groove in the
desk mount - passing
through the bearing.
Then Re-attach desk
mount.
Detach the pole mount from arm using the provided
5mm hex key. Separate the two sections of the pole
mount using the provided 5/32 hex key. Place around
the pole you are mounting to and fi rmly reassemble
the pole mount.
ATTACH POLEMOUNT TO POLE

ICWUSA.com, Inc.
If you have any questions, please call 1-800-558-4435
T2 ARM INSTALLATION INSTRUCTIONS
T2 ARM INSTALLATION INSTRUCTIONS - rev 06/18/2012 mf
page 2
ATTACH PARALINK KEYBOARD TRAY
Loosen knob to adjust Paralink.
Adjust horizontally for keyboard tray
and vertically for monitor. Tighten
knobs when in desired position.
Attach the keyboard tray
to the Keyboard Mount
using the supplied 5/16-
18 socket head screw.
ADJUST BALL VESA
TENSION & HEIGHT
Use the slider knob
to loosen the slider to
adjust the height of the
monitor on the Paralink.
Adjust the pivot tension
of the ball by gently
and evenly tightening
or loosening the four
screws on the back of
the ball VESA.
Slider Knob
Pivot tension
adjustment
screws
ATTACH VESA
TO MONITOR
Using a phillips
screw driver,
attach the VESA
plate to the back
of your LCD
monitor.
ADJUST
PARALINK TILT
Adjust Monitor to desired
position with ball VESA.
Tilt your monitor 50°
in any direction. Adjust
your monitor between
portrait and landscape
by rotating ball VESA.
Adjust monitor depth
by moving the paralink
forward or back then
tighting the depth
adjustment knob.
Depth
Adjustment
Knob
ATTACH KEYBOARD TO MONITOR
Attach the Paralink
Keyboard Mount to
the Monitor Mount
by using the 3/8-16
screw and lock washer
provided