IDEAL 61-764 User manual

IDEAL INDUSTRIES, INC.
TECHNICAL MANUAL
MODELS: 61-764
61-766
61-768
The Service Information provides the following information:
•Precautions and safety information
• Specifications
• Performance test procedure
• Calibration and calibration adjustment procedure
• Basic maintenance (replacing the battery)
Form number: TM61764-6-8
Revision: 5. Date: Nov 2007
Form number TM61764-6-8 Rev 5 November 2007

TABLE OF CONTENTS
Title Page
Introduction 1
Precautions and Safety Information 1
Symbol Table 1
TightSight™ Display Notes 1
High Voltage Warning (HI-V) 2
Safety Information 2
Certifications and Compliance 3
Specifications 3
GeneralSpecification 3
VoltageSpecifications 4
CurrentSpecifications 4
Resistance Specifications 4
Frequency Specification 4
Capacitance Specifications 4
Continuity Specifications 4
Performance Verification 5/6
Calibration 7/8
Calibration Reference Points 9/10
Replacing the Battery 11
Form number TM61764-6-8 Rev 5 November 2007

Page 1
Introduction Warning
To avoid shock or injury, do not perform the verification
tests or calibration procedures described in this manual
unless you are qualified to do so.
The information provided in this document is for the use
of qualified personnel only.
Caution
The 61-760 series contains parts that can be damaged by static
discharge. Follow the standard practices for handling static sensitive
devices.
For additional information about IDEAL INDUSTRIES, INC. and its products,
and services, visit IDEAL INDUSTRIES, INC. web site at:
www.idealindustries.com
Precautions and Safety Information
UsethemeteronlyasdescribedintheUsers Manual. If you do not
do so, the protection provided by the meter may be impaired.
Read the “Safety Information” page before servicing this product.
Inthismanual,aWarning identifies conditions and actions that
pose hazard (s) to the user; a Caution identifies conditions and
actions that may damage the meter or the test instruments.
The Symbols
The symbols used on the meter and in this manual are explained
inTableA.
Table A Symbols
Symbol Description Symbol Description
Battery HI-V High Voltage Indicator
>30 V indicator is on
Cautionary or important
information in manual Continuity indicator
Danger- Risk of electrical
shock
Double Insulation- Protection
Class II
CAT III IEC Over-voltage Category III
CAT IV IEC Over-voltage Category IV
TightSight™ Display Notes:
Only AC/DC amps units of measure are displayed in the TightSight™ display since primary use is
for viewing current measurements in tight locations. The display will show numerical values
only for other functions. The main display is to be used to view units of measure for all other
functions.
Form number TM61764-6-8 Rev 5 November 2007

Page 2
High Voltage Warning (HI-V):
The meter beeps and lights an LED when >30V AC/DC voltage is present through test leads of
the meter. This enhanced safety feature alerts the user that dangerous voltage is present across
the leads even if the meter is set on an incorrect function or range.
Notes: This feature does not work through the clamp head as the clamp is intended to only
measure current. Audible indication can be turned off by sliding the switch in battery
compartment.
SAFETY
Review the following safety precautions to avoid injury and prevent damage to this product or any
products connected to it. To avoid potential hazards, use the product only as specified.
CAUTION.
These statements identify conditions or practices that could result in damage to the equipment or other
property.
WARNING.
These statements identify conditions or practices that could result in personal injury or loss of life.
Specific precautions
Do not operate without covers. To avoid personal injury, do not apply any voltage or current to the
product without the covers in place.
Electric overload. Never apply a voltage to a connector on the product that is outside the range specified
for that connector.
Avoid electric shock. To avoid injury or loss of life, do not connect or disconnect probes or test leads
while they are connected to a voltage source.
Do not operate in wet/damp conditions. To avoid electric shock, do not operate this product in wet or
damp conditions.
Form number TM61764-6-8 Rev 5 November 2007

Page 3
Certifications and Compliances
Safety Designed to EN 61010-1, EN 61010-2-032, UL 61010B-1,
UL 61010B-2-032 specifications
1000V DC Category III
600V DC Category IV
750V AC Category III
Input rating
600V AC Category IV
Over voltage category CAT IV: Outside and service entrance.
CAT III: Distribution level mains, fixed installation.
CAT II: Local level mains, appliances, and portable equipment.
CAT I: Signal level, special equipment or parts of
equipment, telecommunication, electronics.
General Specifications
Characteristics Description
Display 3¾ Digit LCD display
Display Count 6600 count, maximum reading 6600
Over range Indication “OL” is displayed
Sampling Rate 2.0 time/second
Operating
Relative Humidity 0°C to 50°C (32°F to 122°F)
0 ~ 70% RH
Storage Environment: -20°C to 60°C (-4°F to 140°F) at <80% relative humidity
Power source: 9V Battery (NEDA 1604)
Battery Life: 200 hours typical (alkaline) {61-764}
200 hours typical (alkaline) {61-766}
150 hours typical (alkaline) {61-768}
Low Battery Indicator: symbol indicates low battery voltage
Auto power off Approximately 30 minutes
Dimensions 8.7” H X 3.1 ” W X 1.8 ” D
222mm H X 80mm W X 45.5mm D
Maximum Cable Size ACA 1¼” (36mm)
Weight: Approximately 12.4 oz. or 350g including battery
RANGES and ACCURACY SPECIFICATION
Accuracy: Accuracy specifications at 23°C ±5°C (73.4°F ±9°F) less than 75% RH.
Temperature Coefficient: 0.1 times the applicable accuracy specification per degree C
from 0°C to 18°C and 28°C to 50°C (32°F to 64°F and 82°F to 122°F)
Electrical Specification: Accuracy are ±(reading plus number of digits) at 23°C ±5°C
(73.4°F ±9°F) <75% RH
Form number TM61764-6-8 Rev 5 November 2007

Page 4
61-764
Function /
Range Ranges Accuracy
660.0mV, 50Hz - 60Hz 1.7% + 8digits
6.600V/66.00V/660.0V, 50Hz - 100Hz 1.2% + 8 digits
6.600V/66.00V/660.0V, 100Hz - 400Hz 1.5% + 8 digits
AC Voltage
750V, 50Hz - 400Hz 1.5% + 8 digits
660.0mV 1.0% + 2 digits
DC Voltage 6.600V/66.00V/660.0V/1000V 0.5% + 2 digits
66.00A/660.0A, 50Hz - 60Hz 1.7% + 8 digits
AC Current 66.00A/660.0A, 60Hz - 400Hz 3.0% + 8 digits
660.0Ω/6.600KΩ/66.00KΩ/400.0KΩ1.0% + 4 digits
4.000MΩ5.0% + 4 digits
Resistance 10.00MΩ12.0% + 5 digits
Continuity <40Ωon Continuity Not Specified
61-766
Function /
Range Ranges Accuracy
660.0mV, 50Hz - 60Hz 1.7% + 8 digits
6.600V/66.00V/660.0V, 50Hz - 100Hz 1.2% + 8 digits
6.600V/66.00V/660.0V, 100Hz - 400Hz 1.5% + 8 digits
AC Voltage
(True RMS)
750V, 50Hz - 400Hz 1.5% + 8 digits
660.0mV 1.0% + 2 digits
DC Voltage 6.600V/66.00V/660.0V/1000V 0.5% + 2 digits
66.00A/660.0A, 50Hz - 60Hz 1.7% + 10 digitsAC Current
(True RMS) 66.00A/660.0A, 60Hz - 400Hz 3.0% + 10 digits
Capacitance 6.600µ/66.00µ/660.0µ F 3.0% + 10 digits
Frequency 20Hz ~ 400Hz (Auto-ranging) 0.1% + 3 digits
660.0Ω/6.600KΩ/66.00KΩ/400.0KΩ1.0% + 4 digits
4.000MΩ5.0% + 4 digits
Resistance 10.00MΩ12.0% + 5 digits
Continuity <40Ωon Continuity Not specified
61-768
Function /
Range Ranges Accuracy
660.0mV, 50Hz - 60Hz 1.7% + 8 digits
6.600V/66.00V/660.0V, 50Hz - 100Hz 1.2% + 8 digits
6.600V/66.00V/660.0V, 100Hz - 400Hz 1.5% + 8 digits
AC Voltage
(True RMS)
750V, 50Hz - 400Hz 1.5% + 8 digits
660.0mV 1.0% + 2 digits
DC Voltage 6.600V/66.00V/660.0V/1000V 0.5% + 2 digits
660.0A, 50Hz - 60Hz 2.0% + 10 digitsAC Current
(True RMS) 660.0A, 60Hz - 400Hz 3.0% + 10 digits
DC Current 660.0A 2.0% + 5 digits
660.0Ω/6.600KΩ/66.00KΩ/400.0KΩ1.0% + 4 digits
4.000MΩ5.0% + 4 digits
Resistance 10.00MΩ12.0% + 5 digits
Continuity <40Ωon Continuity Not specified
Form number TM61764-6-8 Rev 5 November 2007

Page 5
AC Converter: 61-764 - Average responding, RMS Calibrated to Sine Wave
61-766, 61-768 – True RMS sensing
Overload Protection:
AC and DC Voltage: Not to exceed 1000V DC or 750VAC RMS
AC Current: Not to exceed 660A AC
DC Current: Not to exceed 660A DC
Resistance: Not to exceed 600V DC or VAC RMS
Capacitance, Frequency, Continuity: Not to exceed 600V DC or VAC RMS
PERFORMANCE VERIFICATIONS
Perform the following analysis; if the meter conforms to the limits listed in Table 1 through 7 the meter is
functioning correctly. If the meter does not conform to any of the listed limits the calibration procedure
must be performed.
Performance Verification Preparation
1. Turn on the calibrator, allow calibrator to warm up. Temperature stabilization
should be reached after 30 minutes.
2. Remove battery cover and using a calibrated meter to ensure the battery measures a minimum of 7.5V
DC. If the battery measures under 7.5V DC, replace the battery (see Battery Replacement page 11)
before beginning the performance test.
3. Input the values listed in Table 1 through 7.
Table 1 AC Voltage Test
Function
/Range Input Low Limit High Limit Model Number
V AC 660mV 350mV AC @ 50Hz 343.2 356.8 61-764, 61-766, 61-768
V AC 6.6V 3.5V AC @ 50Hz 3.450 3.550 61-764, 61-766, 71-768
V AC 6.6V 3.5V AC @ 400Hz 3.439 3.561 61-764, 61-766, 71-768
V AC 66V 35V AC @ 50Hz 34.50 35.50 61-764, 61-766, 61-768
V AC 66V 35V AC @ 400Hz 34.39 35.61 61-764, 61-766, 61-768
V AC 660V 350V AC @ 50Hz 345.0 355.0 61-764, 61-766, 61-768
V AC 660V 350V AC @ 400Hz 343.9 356.1 61-764, 61-766, 61-768
V AC 750V 700V AC @ 50Hz 681 719 61-764, 61-766, 61-768
V AC 750V 700V AC @ 400Hz 681 719 61-764, 61-766, 61-768
Table 2 DC Voltage Test
Function
/Range Input Low Limit High Limit Model Number
V DC 660mV 350mV 346.3 353.7 61-764, 61-766, 61-768
V DC 6.6V 3.5V 3.480 3.520 61-764, 61-766, 61-768
V DC 66V 35V 34.80 35.20 61-764, 61-766, 61-768
V DC 660V 350V 348.0 352.0 61-764, 61-766, 61-768
V DC 1000V 900V 893 907 61-764, 61-766, 61-768
Form number TM61764-6-8 Rev 5 November 2007

Page 6
Table 3 AC Current Test
Function
/Range Input Low Limit High Limit Model Number
A AC 66A 10A AC @ 50Hz 9.75 10.25 61-764
A AC 66A 10A AC @ 50Hz 9.73 10.27 61-766
A AC 66A 10A AC @ 400Hz 9.62 10.38 61-764
A AC 66A 10A AC @ 400Hz 9.60 10.40 61-766
A AC 660A 500A AC @ 50Hz 490.7 509.3 61-764
A AC 660A 500A AC @ 50Hz 490.5 509.5 61-766
A AC 660A 500A AC @ 50Hz 489.0 511.0 61-768
A AC 660A 500A AC @ 400Hz 484.2 515.8 61-764
A AC 660A 500A AC @ 400Hz 484.0 516.0 61-766, 61-768
Table 4 DC Current Test
Function
/Range Input Low Limit High Limit Model Number
A DC 660A 100A DC 97.5 102.5 61-768
A DC 660A 500A DC 489.5 510.5 61-768
Table 5 Resistance Test
Function /Range Input Low
Limit High Limit Model Number
Ω660 100Ω98.6 101.4 61-764, 61-766, 61-768
Ω6.6K 1KΩ.986 1.014 61-764, 61-766, 61-768
Ω66K 10KΩ9.86 10.14 61-764, 61-766, 61-768
Ω400K 100KΩ98.6 101.4 61-764, 61-766, 61-768
Ω4M 1MΩ.946 1.054 61-764, 61-766, 61-768
Ω10M 10MΩ8.75 112.5 61-764, 61-766, 61-768
Table 6 Capacitance and Frequency Test
Function /Range Input Low
Limit High Limit Model Number
Hz
{through clamp} 50Hz @ 5A 49.6 50.4 61-766
Hz {auto}
{through clamp} 200Hz @ 10A 199.5 200.5 61-766
MFD 6.6µF 1µF .960 1.040 61-766
MFD 66µF 10µF 9.60 10.40 61-766
MFD 660µF 100µF 96.0 104.0 61-766
Table 7 Continuity Check
Function
/Range Test Value Low limits High Limit Model Number
20Ωbeep on 19.4 20.6
Continuity 40Ωbeep off 39.2 40.8
61-764, 61-766, 61-768
Form number TM61764-6-8 Rev 5 November 2007

Page 7
CALIBRATION
Calibration Preparation
1. Turn on the calibrator, allow calibrator to warm up. Perform calibration at
23±2°C (73.4°F ±3.5°F) at relative humidity of < 70%. Temperature stabilization should be
reached after 30 minutes.
2. Disconnect the test leads and turn the range switch to “OFF”.
3. Remove the screws holding the battery cover, one at the jaw, and the screw for the TightSight™
cover.
4. Remove the case bottom using care not to damage the leads of battery snap and spring
to the continuity beeper. (Beeper is attached to the bottom case cover.)
5. Using a calibrated meter ensure the battery measures a minimum of 7.5V DC.
If the battery measures under 7.5V DC, replace the battery (see Battery Replacement page 11).
Calibration Procedure
It is recommended that all IDEAL meters undergo the following calibration procedure on
an annual basis.
The class of calibrator or equipment should have an accuracy that exceeds, by an expectable ratio the
accuracy of this instrument.
V DC Calibration:
61-764 (Refer to Figure 1A), 61-766 (Refer to Figure 2A), 61-768 (Refer to Figure 3A)
1. Set the function / range to 6.6V DC.
2. Connect the calibrator to the Vand COM inputs on the meter.
3. Output 3.900V DC.
AdjustVR1(VR1KΩ) until unit display reads 3.900. (61-764, 61-766)
AdjustVR2(VR1KΩ) until unit display reads 3.900. (61-768)
4. De-energize source and remove test leads
V AC Zero Calibration:
61-766 (Refer to Figure2A), 61-768 (Refer to Figure 3A)
1. Set the function /range to 750V AC.
2. Short the Vand COM input on the meter.
3. Adjust VR3 (VR 220kΩ) until display reads 000.
4. De-energize source and remove test leads.
V AC Calibration:
61-766 (Refer to Figure 2A), 61-768 (Refer to Figure 3A)
1. Set the function/range to the 6.6V AC.
2. Connect the calibrator to the Vand COM inputs on the meter.
3. Output 3.900VAC/60Hz.
Adjust VR2 (VR 1KΩ) until unit display reads 3.895 ±1 digit. (61-766)
Adjust VR1 (VR 1KΩ) until unit display reads 3.895 ±1 digit. (61-768)
4. De-energize source and remove test leads.
Form number TM61764-6-8 Rev 5 November 2007

Page 8
Calibration Procedure (cont’d)
A AC Calibration:
61-764 (Refer to Figure 1B), 61-766 (Refer to Figure 2B) (Adjustments made under front panel label.)
1. Set the function / range to the 660A AC.
2. Set output of the AC calibrator for 10.00A/60Hz +/- 0.01% and connect it to Coil = 10N = 100.0A
AC.
3. Clamp the jaws to the coil = 10N.
4. Adjust VR2 (VR 1KΩ) for a display reading of 100.0 ±1 digit. (61-764)
Adjust VR4 (VR 2KΩ) for a display reading of 100.0 ±1 digit. (61-766)
5. De-energize source and remove test leads.
A DC Zero Calibration
61-768 (Refer to Figure 3B)
1. Set the function/range to A DC.
2. Short the V and COM inputs on the meter.
3. Adjust VR5 (VR 5KΩ) until display reads 000.
4. De-energize source and remove test leads.
A DC Calibration
61-768 (Refer to Figure 3B)
1. Set the function / range to the A DC.
2. Set output of the DC calibrator for +10.00A ±0.01% and connect it to Coil = 10N = +100.0A DC.
3. Clamp the jaws to the coil = 10N.
4. Adjust VR4 (VR 3.3KΩ) for a display reading of 100.0 ±1 digit.
5. De-energize source and remove test leads.
Calibration of the 61-760 series is complete.
Remove all leads from the calibrator and equipment.
Return unit to proper operating condition.
Form number TM61764-6-8 Rev 5 November 2007

Page 9
61-764 (Figure 1A) 61-764 (Figure 1B)
61- 766 (Figure 2A) 61-766 (Figure 2B)
Form number TM61764-6-8 Rev 5 November 2007

Page 10
61-768 (Figure 3A) 61-768 (Figure 3B)
Form number TM61764-6-8 Rev 5 November 2007

Page 11
Battery Replacement (Refer to Figure 4)
1. Disconnect the test leads from any circuit under test and turn off meter.
2. Use a Philips head screwdriver to remove the screws on battery cover.
3. Remove battery from the battery compartment.
4. Install new 9V battery (NEDA #1604). An alkaline type is recommended.
5. Install new battery into compartment using care to install to proper polarity.
6. Reinstall battery cover.
Figure 4
Form number TM61764-6-8 Rev 5 November 2007