IDEAL SPLIT-JAW 61-096 User manual

Form Number TM61096 Rev 2 Nov 2010
IDEAL INDUSTRIES INC.
TECHNICAL MANUAL
MODEL 61-096 Split Jaw Smart Meter
The Service Information provides the following information :
• Precautions and safety information
• Specifications
• Basic maintenance (cleaning, replacing the battery and fuses)
• Performance test procedures
• Calibration and calibration adjustment procedures
Form Number: TM61096
Revision: 2. Date: Nov 2010
99 Washington Street
Melrose, MA 02176
Phone [phone]
Toll Free 1-800-517-8431
Visit us at www.TestEquipmentDepot.com

Form Number TM61096 Rev 2 Nov 2010
TABLE OF CONTENTS Page
Introduction
1
Precautions and Safety Information
1
Symbols
1
Safety
2
Specifications
3
General Specification
3
Voltage Specification
4
Resistance & Continuity Specification
4
Current Specification
4
Physical and environment characteristics
5
Certification and compliance
5
Required Equipment
6
Basic Maintenance
7
Opening the Meter Case
7
Replacing the Battery
7
Performance Tests
8
Testing the Voltage Function
8
Testing the Resistance Function
9
Testing the AC Current Function
10
Calibration
11
Calibrating DCV, ACV, Resistance, ACA Functions
11
Calibration Adjustment Points
12/13
i

Form Number TM61096 Rev 2 Nov 2010
Introduction
Warning
To avoid shock or injury, do not perform the verification tests or calibration procedures
described in the manual unless you are qualified to do so.
The information provided in this document is for the use of qualified personnel only.
Caution
The 61-096 contain parts that can be damaged by static discharge.
Follow the standard practices for handling static sensitive devices.
Precautions and Safety Information
Use the Meter only as described in the Service Manual. If you do not do so, the protection provided by the
Meter may be impaired. Read the “Safety Information” page before servicing this product.
In this manual, a Warning identifies conditions and actions that pose hazard (s) to the user; a Caution
identifies conditions and actions that may damage the Meter or the test instruments.
The Symbols
The symbols used on the Meter and in this manual are explained in Table 1.
Table A. The Symbols
Risk of electric shock
See instruction card
DC measurement
Equipment protected by double or reinforced
insulation
Battery
Earth
AC measurement
Conforms to EU directives
1

Form Number TM61096 Rev 2 Nov 2010
SAFETY
Review the following safety precautions to avoid injury and prevent damage to this product or products
connected to it. To avoid potential hazards, use the product only as specified.
CAUTION: These statements identify conditions or practices that could result in damage to the
equipment or other property.
WARNING: These statements identify conditions or practices that could result in personal injury or
loss of life.
Specific precautions
Do not operate without covers. To avoid personal injury, do not apply any voltage or current to the
product without covers in place.
Electric overload. Never apply a voltage to a connector on the product that is outside the range
specified for that connector.
Avoid electric shock. To avoid injury or loss of life, do not connect or disconnect probes or test leads
while they are connected to a voltage source.
Do not operate in wet/damp conditions. To avoid electric shock, do not operate this product in wet or
damp conditions.
2

Form Number TM61096 Rev 2 Nov 2010
SPECIFICATIONS
All specifications are warranted unless noted typical and apply to the 61-096
Stated accuracies are at 23°C±5°C at less than 80% relative humidity and without the battery indicator
displayed.
General specifications
Characteristics
Description
Display count
6000
Numeric update rate
5 times / sec
Polarity display
Automatic
Overrange display
“OL” is display
Low voltage indicator
is indicated
Automatic power-off time
Automatic backslit off = 30 minutes
Power source
Power 9V battery
Maximum input voltage
1000V CAT III between V and COM
Maximum floating voltage
1000V CAT III between any terminal and earth ground
V connector
V, V, Ω,
Temperature Coefficient
0.2×(Spec. Accuracy) / °C, <18°C or >28°C
Battery Life
180 hours typical (alkaline)
3

Form Number TM61096 Rev 2 Nov 2010
Measurement Characteristics
Accuracy is ±(% reading + number of digits) at 23°C ± 5°C, less than 80% R.H.
DC / AC Volts
Function
Range
Accuracy
V
1.3V ~ 750.0V
±(1.5% reading + 3 digits)
50Hz ~ 500Hz
V
1.8V ~ 1000V
±(1% reading + 2 digits)
-0.6V ~ -1000V
±(1% reading + 4 digits)
Overload protection: 750Vrms // 1000VDC
Max. Operation time: DT=30s for ≥ 30V
Input Impedance: ≥ 4K for input voltage up to 30V. Impedance increase with input voltage to 330KΩ at
1000V.
Resistance & Continuity
Function
Range
Accuracy
Ω
0.0Ω ~ 99.9Ω
±(2% reading + 1Ω)
100Ω ~ 2000Ω
±(2% reading + 2 digits)
Overload protection: 750Vrms // 1000VDC
Max. Open Voltage: 1.5V
Continuity check: Internal sounds activates if the resistance of the circuit under test is less than 25Ω.
It will then turn off if the resistance is increased beyond 400Ω.
Operating temperature: 0°C ~ 40°C
AC Current
Function
Range
Accuracy
A
0.6A ~ 200.0A
±(1.8% reading + 3 digits)*
50Hz ~ 60Hz
Overload protection: 400A
*±(1.8% reading + 6 digits) ≤ 50A
4

Form Number TM61096 Rev 2 Nov 2010
Physical and Environmental Characteristics
Characteristics
Description
Dimensions (W×H×L)
84mm×188mm×41mm
Weight (with battery)
230g
Environmental characteristics
Description
Temperature operating
0 to +50°C
Non-Operating
-20 to +60°C
Humidity (operating)
<80% R.H.
Altitude Operating
2,000M (6560 ft.)
Non-Operating
12,300M (40354 ft.)
Vibration & shock Operating
MIL-T-28800E TYPE II Class 5
2.66gRMS, 5 to 500 Hz, 3axes
(10 minutes each)
Indoor Use
Indoor Use
Certifications and compliances
Safety
IEC 61010 and designed to meet UL 3111 specifications
Input rating
V / Ω: Category III 1000 Volts
Over voltage category
CAT III: Distribution level mains, fixed installation.
CAT II: Local level mains, appliances, portable equipment
CAT I: Signal level, special equipment or parts of equipment,
telecommunication, electronics.
Pollution Degree 2
Do not operate in environments where conductive
Pollutants may be present.
EC Declaration
of Conformity
Meets the intent of Directive 89/336/EEC for Electromagnetic
Compatibility and Low Voltage Directive 73/23/EEC for specifica -
tions as listed in the official Journal of the European Communites:
En 55011 Class A: Radiated and Conducted
Emissions.
En 50082-1 Immunity: IEC 801-2 Electrostatic Discharge
IEC 801-3 RF Radiated
En 61010-1 Safety requirements for electrical equipment for
measurement, control, and laboratory use.
5

Form Number TM61096 Rev 2 Nov 2010
Required Equipment
Required equipment is listed in Table B. If the recommended models are not available, equipment with
equivalent specifications may be used.
Repairs or servicing should be performed only by qualified personnel.
Table B. Required Equipment
Equipment
Required Characteristics
Recommended Model
Calibrator
AC Voltage Range: 0 ~ 750V AC
Accuracy: ±0.07% (Basic)
Frequency Range: 40 ~ 1KHz
Accuracy: ±2%
DC Voltage Range: 0 ~ 1000V DC
Accuracy: ±0.006% (Basic)
Current Range: 0 ~ 10A
Accuracy: AC (40Hz to 1KHz): ±0.08% (Basic)
Resistance Range: 1Ω ~ 100MΩ
Accuracy: ±0.03% (Basic)
1. Fluke 5700A Calibrator
2. 50 Turns Coil
6

Form Number TM61096 Rev 2 Nov 2010
Basic Maintenance
Warning
To avoid shock, remove the test leads and any input signals before opening the case or replacing the
battery.
Opening the Meter Case
Caution
To avoid unintentional shock circuit, always place the uncovered Meter assembly on a protective
surface. When the case of the Meter is open, circuit connections are exposed.
To open the Meter case, and do the following:
1. Disconnect test leads from any live source, push the button to OFF, and remove the test leads from
the front terminals.
2. Remove the battery door by using a flat-blade screwdriver to turn the battery door screws turn
counter-clockwise.
3. The case bottom is secured to the case top by two screws. Using a Phillips-had screwdriver, remove
the two screws.
Replacing the Battery
The Meter powered by 9V battery for 61-096
To replace the battery refer to Figure.
7

Form Number TM61096 Rev 2 Nov 2010
Performance Tests
The following performance tests verify the complete operability of the Meter and check the accuracy of
each Meter function against the Meter’s specifications.
Accuracy specifications are valid for a period of one year after calibration, when measured at an
operating temperature of 18°C to 28°C and a maximum of 80% relative humidity.
To perform the following tests, it is not necessary to open the case, no Adjustments are necessary,
merely make the required connections, apply the designated inputs, determine if the reading on the
Meter display falls within the acceptable range indicated.
If the Meter fails any of these tests, it needs calibration adjustment or repair.
Testing the voltage Function
To verify accuracy in the AC and DC voltage ranges, do the following:
1. Push the button to start your meter.
2. Connect the Calibrator to the VΩ and COM inputs on the Meter.
3. Set the Calibrator for the voltage and frequency from step 1 to 8 in Table 1.
4. Compare the reading on the Meter display with the display reading shown in Table 1.
5. If the display reading falls outside of the range shown in Table 1, the Meter does not meet
specification.
Table 1 AC Voltage Test:
Step
Input
Frequency
Reading
1
3.0V
50Hz
2.7 to 3.3
2
3.0V
500Hz
2.7 to 3.3
3
30.0V
50Hz
29.3 to 30.8
4
30.0V
500Hz
29.3 to 30.8
5
300.0V
50Hz
295.2 to 304.8
6
300.0V
500Hz
295.2 to 304.8
7
600.0V
50Hz
590.7 to 609.3
8
600.0V
500Hz
590.7 to 609.3
8