Deployment Environments
Themanufacturer cannot be held responsible incase of non-compliance withthe
following recommendations or incorrect use of the terminal.
Repair and Accessories
Do not attempt to repair theMorphoAccess® SIGMA Extreme Series terminal
yourself. Themanufacturer cannot be held responsible for any damage/accident
that may result from attempts to repair components. Any work carried out by
non-authorized personnel will void your warranty.
Only use the terminal with its original accessories. Attempts to use unapproved
accessories with your terminalwill void your warranty.
Micro SD Card
Themicro SD cardis linked to the terminal: it shall not be transferred from one
product to another.
Date / Time synchronization
The MorphoAccess® SIGMA Extreme Series terminal clock has a +/- 10 ppm
typical time deviation at +25ºC (roughly +/- 1sec per day). At lower and higher
temperature, deviation may be greater (maximum : 8sec per 48 hours).
When the terminal is used for applications requiringhigh time precision, it is
strongly recommended to synchronize the terminal with an external clock.
Firmware release
To get the best of our technology, we recommend you to download and install
thelast firmware release. Please check our website.
Recommendations
WARNING: Cleaning & Disinfection precautions
To clean the terminal, a dry cloth is recommended, especially for the
biometric sensor.
To disinfect the terminal, moisten a non-abrasive wipe with the
disinfectant Windex® Multi-Surface (or similar product containing L-
Lactic acid) and wipe the device’s surfaceandleave the surface wet
with disinfectant for at least 5 minutes. Any other practices (hydrogen
peroxide, bleach, chlorine, soda, alcohol, quaternary ammonium etc)
permanently damage and/or negatively impact the performances of the
device.
!
1
4
5
6
4
2
7
!
!
3
1
3
12
127,8mm
275,8mm
IP65*
!
1
2
2T20
3
*IP65 : Indoor use only
Not evaluated by UL
General precautions
Do not exposethe terminal to extreme temperatures.
When the environment is very dry, avoid synthetic carpeting near the
MorphoAccess® SIGMA Extreme terminal, to reduce the risk of unwanted
electrostatic discharge.
Areas containing combustibles
Do not install the terminal in the vicinity of gas stations or any other installation
containing flammableor combustible gases or materials. Theterminal is not
designed to be intrinsically safe.
The terminal should be installed in controlled lighting conditions
Avoidbiometric sensor exposure to a blinking light.
Avoid direct exposure of the biometric sensor to sunlight or to UV lights.
-20° to +60 °C (-4°to 140°F)
Operatinghumidity
Storage temperature
Storage humidity
10 % < RH < 95% (non condensing)
- 25° to + 70 °C (-13° to 158°F)
5% < RH < 95 %
IP code IP65 rated
For UL 294 compliance, theproducts are ratedfor indoor use
Operatingtemperature
In exceptional circumstances of ambient temperature and sun exposure,
the screen may feel hot.
!
Wiring Overview
!WARNING: Power Supply from electrical source shall be switched off before starting
the installation.
Before proceeding, make sure that the person in
charge of installation and connections, is properly
connected to earth, in order to prevent
Electrostatic Discharges (ESD).
External Power supply: 12/24 VDC
(regulated and filtered) 1A min @12VDC or
500mA min @24VDC, IEC 60950-1 standard
compliant. A 12 Volts power supply compliant
with SIA's Wiegand standard will also be
suitable. If sharing power between devices,
each unit must receive 1A (e.g. twounits
would requirea 12 VDC, 2A supply).
For UL compliance the units shall be
powered via a class 2 output from a UL 294
power supply.
A battery backup or uninterrupted power
supply (UPS) with built-in surge protection
is recommended.
IDEMIA recommends usinga Gauge AWG20 for 12V power supply.
Thevoltage measuredon the product block connector of the terminal must be equal
to 12V-24V (-15% / +10%).
Thevoltage drop due tothe cable shall be takeninto account. Thetable below shows
themaximum voltage drop between the power source and the terminal, depending on
the length of the cable.
Power Over Ethernet (POE): power can
be provided throughRJ-45 connector
using a PSE (Power Sourcing
Equipment) IEEE802.3af or
IEEE802.3at type 1 compliant.
For UL compliance the units shall be
powered via a UL 294B PSE power
supply, rated 48VDC (-10%/+15%).
Theterminal is aClass 0 (15.4 W)
PD (PoweredDevice).
!WARNING: Under
powering may cause
memory and data
corruption; over powering
may cause hardware
damage. Both of these
situations will void the
warranty
Maximum drop voltage (V)
Gauge
AWG Diameter
(mm)at 1m at 5m at 10m
24
22
20 0.64
0.51
0.03
0.05
0.08
0.17
0.26
0.42
0.33
0.53
0.84
0.81
Relay output 30VDC, 1A.
Suitable for inductive and resistive
loads. Inductive load management
requires a parallel diode for a better
contact lifetime.
Tamper 30VDC, 100 mA (Resistive).
UL has not verified Wi-Fi Capabilities.
Ethernet connection is for supplemental use not UL evaluated.
For UL installations only Wiegand is to be used.
UL has not evaluated GPIO and RS422/485 communication.
