IEI Technology HYPER-EHL User manual

Pico-ITX SBC Supports Intel® Celeron® J6412/N6210 on-board SoC
with 4GB LPDDR4x, HDMI, iDPM, 2.5GbE LAN, M.2, PCIe x4 Slot,
iSATA 6Gb/s, COM, USB 3.2 Gen 2, and RoHS
HYPER-EHL
Quick Installation Guide
Version 1.0
May 16, 2023
Package List
HYPER-EHL package includes the following items:
 1 x HYPER-EHL single board computer
 1 x iSATA cable
 1 x QIG
©2023 Copyright by IEI Integration Corp.
All rights reserved.

2
Specifications
 CPU:
Onboard Intel® Atom® x6000 series / Pentium® / Celeron®
processor (Elkhart Lake platform)
Intel® Celeron® J6412 on-board SoC
(up to 2.6GHz, quad-core, 1.5M cache, TDP=10W)
Intel® Celeron® N6210 on-board SoC
(up to 2.6GHz, dual-core, 1.5M cache, TDP=6.5W)
 Memory:
On-board 4GB 3200 MHz LPDDR4X (system max. 8GB)
 BIOS:
AMI UEFI BIOS
 Graphics Engine:
Intel® UHD Graphics (Gen11)
 Display Output:
Dual independent display
1 x HDMI 1.4 (up to 4096 x 2160 @ 30Hz)
1 x IEI iDPM 3040 slot (only for IEI eDP/LVDS/VGA module)
 Ethernet:
1 x 2.5GbE via Intel® I225V controller
 External I/O Interface:
2 x USB 3.2 Gen 2x1 Type-A (10Gb/s)
 Internal I/O Interface:
1 x iSATA 6Gb/s
2 x USB 2.0 (2x4 pin, p=2.0)
1 x RS-232/422/485 (1x9 pin, p=1.25)
 Front Panel:
1 x Power button connector (1x2 pin, p=1.25)
1 x Reset button connector (1x2 pin, p=1.25)
 Expansions:
1 x M.2 2242 M key (PCIe x2 & USB 2.0)
1 x PCIe x4 slot (PCIe Gen3 x4 signal, x4 or x2+x2 or 1+x1+x1+x1)
 Digital I/O:
1 x 8-bit digital I/O (1x10 pin, p=1.25)

3
 I
2C/SMBus:
1 x SMBus (1x4 pin, p=1.25)
 Power Supply:
12V DC power supply
Support AT/ATX mode
 Power Consumption:
12V@ 2.07A
(Intel® Celeron® J6412 CPU with 4 GB 3200 MHz LPDDR4x
memory, max. loading, EuP mode enabled)
 Watchdog Timer:
Software programmable support 1–255 sec. system reset
 Operation Temperature: 0°C – 60°C
 Storage Temperature: -30°C – 70°C
 Operation Humidity: 5% – 95%, non-condensing
 Dimensions: 100 mm x 72 mm
 Weight: GW:600 g / NW:250 g
Ordering Information
 HYPER-EHLJ6412B-R10:
Pico-ITX SBC supports Intel® Celeron® J6412 quad-core 2.0GHz
on-board SoC with 4GB on-board LPDDR4x memory, HDMI, iDPM,
M.2 M key, USB 3.2, SATA 6GB/s, COM, PCIe x4 for riser card and
RoHS
 HYPER-EHL-N6210B-R10:
Pico-ITX SBC supports Intel® Celeron® N6210 dual-core 1.2GHz
on-board SoC with 4GB on-board LPDDR4x memory, HDMI, iDPM,
M.2 M key, USB 3.2, SATA 6GB/s, COM, PCIe x4 for riser card and
RoHS
 CB-USB02A-RS:
Dual-port USB cable with bracket, 300mm, p=2.0
 32102-000100-200-RS:
SATA power cable, MOLEX 5264-4P to SATA15P

4
 32205-008000-100-RS:
RS-232/422/485 cable, 250mm, 1x9 pin, p=1.25
 HPR-L2S-R10:
PCIe x4 to two PCIe x2 riser card for HYPER on the left side
 HPR-L4S-R10:
PCIe x4 to four PCIe x1 riser card for HYPER on the left side
 HPR-R2S-R10:
PCIe x4 to two PCIe x2 riser card for HYPER on the right side
 HPR-R4S-R10:
PCIe x4 to four PCIe x1 riser card for HYPER on the right side
 iDPM-eDP-R10:
eDP to eDP converter board (for IEI iDPM slot)
 iDPM-LVDS-R10:
eDP to LVDS converter board (for IEI iDPM slot)
All the drivers and utility for the
HYPER-EHL are available on IEI
Resource Download Center. Type
HYPER-EHL and press Enter to find all
the relevant software, utilities, and
documentation. To install software from
the downloaded ISO file, mount the file
as a virtual drive to view its content.
IEI Resource Download Center
https://download.ieiworld.com

5
Jumpers Setting and Connectors
LABEL FUNCTION
J_CMOS1 Clear CMOS button
J_ATX_AT1 AT/ATX power mode setting switch
BAT2 Battery connector
SP1 Buzzer connector
DIO1 Digital I/O connector
JBIOS1 Flash SPI ROM connector
I2C1 I2C connector
ISATA iSATA 6Gb/s connector
PWR_BTN1 Power button connector
RST_BTN1 Reset button connector
COM1 RS-232/422/485 serial port connector
USB2-1 Internal USB 2.0 connector
M2_1 M.2 M-key slot
IP2EHL_XC PCIe Gen3 x4 slot
IDPM IEI iDPM slot
DCIN1 External 12V DC input jack
LAN1 External 2.5GbE connector
HDMI1 External HDMI connector
USB1 External dual USB 10Gb/s connector
J_CMOS1: Clear CMOS Button
PIN NO. DESCRIPTION
NC (default) Keep CMOS Setup
(Normal Operation)
Press button Clear CMOS Setup

6
J_ATX_AT1: AT/ATX Power Mode Setting Switch
PIN NO. DESCRIPTION
Short A - B ATX Power Mode (default)
Short B - C AT Power Mode
BAT2: RTC Battery Connector
PIN DESCRIPTION PIN DESCRIPTION
1 VBATT 2 GND
SP1: Buzzer Connector
PIN DESCRIPTION PIN DESCRIPTION
1 +5V 2 PC_BEEP
DIO1: Digital Input/Output Connector
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 +5V 6 DOUT0
2 DIN0 7 DOUT1
3 DIN1 8 DOUT2
4 DIN2 9 DOUT3
5 DIN3 10 GND
JBIOS1: Flash SPI ROM Connector
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 +3.3V 4 SPI_CLK
2 SPI_CS# 5 SPI_SI
3 SPI_SO 6 GND
I2C1: I2C Connector
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 GND 3 I2C_CLK
2 I2C_DATA 4 +5V

7
ISATA: iSATA 6Gb/s Connector
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 GND 11 +5V
2 GND 12 N/C
3 GND 13 N/C
4 GND 14 GND
5 GND 15 SATA RX+
6 GND 16 SATA_RX‐
7 +5V 17 GND
8 +5V 18 SATA_TX‐
9 +5V 19 SATA_TX+
10 +5V 20 GND
PWR_BTN1: Power Button Connector
PIN DESCRIPTION PIN DESCRIPTION
1 PWR_BTN+ 2 PWR_BTN-
RST_BTN1: Reset Button Connector
PIN DESCRIPTION PIN DESCRIPTION
1 RST_BTN+ 2 RST_BTN-
COM1: RS-232/422/485 Serial Port Connector
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 DCD 6 CTS
2 DSR 7 DTR
3 SIN 8 RI
4 RTS 9 GND
5 SOUT

8
USB2-1: Internal USB 2.0 Connector
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 VCC 2 GND
3 USB_DATA- 4 USB_DATA+
5 USB_DATA+ 6 USB_DATA-
7 GND 8 VCC
M2_1: M.2 M-key Slot
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 GND 2 +V3.3A
3 GND 4 +V3.3A
5 NC 6 NC
7 NC 8 NC
9 GND 10 +V3.3A
11 NC 12 +V3.3A
13 NC 14 +V3.3A
15 GND 16 +V3.3A
17 NC 18 +V3.3A
19 NC 20 NC
21 GND 22 NC
23 NC 24 NC
25 NC 26 NC
27 GND 28 NC
29 PCIE_RX7- 30 NC
31 PCIE_RX7+ 32 NC
33 GND 34 USB+
35 PCIE_TX7- 36 USB-
37 PCIE_TX7+ 38 MKEY_SSD_SLP
39 GND 40 M2_I2C_CLK
41 PCIE_RX6- 42 M2_I2C_DATA
43 PCIE_RX6+ 44 NC
45 GND 46 NC
47 PCIE_TX6- 48 NC
49 PCIE_TX6+ 50 BUF_PLT_RST

9
51 GND 52 NC
53 CLK_M2_B- 54 PCIE_WAKE#
55 CLK_M2_B+ 56 NC
57 GND 58 NC
59 Module Key 60 Module Key
61 Module Key 62 Module Key
63 Module Key 64 Module Key
65 Module Key 66 Module Key
67 NC 68 NC
69 +V3.3A 70 +V3.3A
71 GND 72 +V3.3A
73 GND 74 +V3.3A
75 GND
DCIN1: External 12V DC Input Jack
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 +12V 3 GND
2 GND
LAN1: 2.5GbE RJ-45 Connector
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 LAN1_MDI0P 5 LAN1_MDI2P
2 LAN1_MDI0N 6 LAN1_MDI2N
3 LAN1_MDI1P 7 LAN1_MDI3P
4 LAN1_MDI1N 8 LAN1_MDI3N

10
HDMI1: External HDMI Connector
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 HDMI2_DATA2 2 GND
3 HDMI2_DATA2# 4 HDMI2_DATA1
5 GND 6 HDMI2_DATA1#
7 HDMI2_DATA0 8 GND
9 HDMI2_DATA0# 10 HDMI2_CLK
11 GND 12 HDMI2_CLK#
13 N/C 14 N/C
15 HDMI2_SCL 16 HDM2I_SDA
17 GND 18 +5V
19 HDMI2_HPD
USB1: External Dual USB 3.2 Gen 2 (10Gb/s) Connector
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 VCC 10 VCC
2 USB_DATA- 11 USB_DATA-
3 USB_DATA+ 12 USB_ DATA+
4 GND 13 GND
5 USB3_RX- 14 USB3_RX-
6 USB3_RX+ 15 USB3_ RX+
7 GND 16 GND
8 USB3_TX- 17 USB3_TX-
9 USB3_TX+ 18 USB3_TX+

11
Board Layout: Jumper and Connector Locations
(Unit: mm)