IEI Technology IOWA-LX-600 User manual

1
Half-size pure ISA CPU card with on-board AMD Geode™ LX
[email protected] Processor at FSB 366MHz, 128KB L2 cache,
128MB memory on board include VGA, LAN, USB2.0, CF,
COM, LPT and Audio, RoHS
IOWA-LX-600
Quick Installation Guide
Version 1.0
Mar. 14, 2011
Package List
IOWA-LX-600 package includes the following items:
l1 x IOWA-LX-600 Single Board Computer
l1x USB Cable
l1 x IDE Flat Cable
l1 x KB/MS Y Cable
l1 x Audio Cable
l1 x Mini Jumper Pack
l1 x Utility CD (within manual)
l1 x QIG (Quick Installation Guide)
l1xOne Key Recovery CD
©2011 Copyright by IEI Technology corp.
All rights reserved.

2
Specifications
lCPU:
On-board AMD Geode™ LX 600@ processor at FSB 366MHz,
128KB L2 cache
lSystem chipset:AMD Geode™ CS5536
lBIOS: Award BIOS
lSystem memory:
On-board 128MB (max.) 200/266MHz DDR SDRAM supported.
One 204-pin 512MB (max.) 200/266MHz DDR SO-DIMM
supported.
lEthernet:
10/100Mbps Realtek RTL8100C Ethernet controller
lSuper IO: Winbond W83627EHG
lI/O Interface:
2x RS-232
1 x RS-422/485
1 x IDE
1 x FDD
1 x LPT
2x SATA (Optional for IOWA-LX-600S-R10)
1 x CF type II
4 x USB 2.0 (by pin header)
1 x PS/2 KB/MS
lExpansion:
ISA bus supported via golden finger
lDigital I/O: 8-bit digital I/O, 4-bit input / 4-bit output
lDisplay Output:
Single HD VOP 2.0 output
1920x1440 CRT output
1600x1200 TFT output
lGraphic Engine:
VGA integrated in the AMD Geode™ LX 600
lAudio: Realtek ALC203 with AC'97 codec

3
lWatchdog Timer:
Software programmable supports 1~255sec.System reset
lPower supply:5V/12V via ISA bus, AT/ATX mode supported
lPower Consumption:
[email protected], [email protected] (On-board AMD Geode™ LX 600 CPU
366MHz with 200MHz DDR 128MB On-board Memory and
333MHz DDR 512MB Memory)
lTemperature: Operation: -10°C~60°C
lHumidity: Operation: 5%~95%non-condensing
lDimension: 185mm x 122mm
Ordering Information
lIOWA-LX-600-R10：Half-size pure ISA CPU card with on-board AMD
Geode™ LX 600 processor at FSB 366MHz, 128KB L2 cache, 128MB
memory on board include VGA, LAN, USB 2.0, COM, CF, LPT and
Audio, RoHs
lIOWA-LX-600S-R10：Half-size pure ISA CPU card with on-board AMD
Geode™ LX 600 processor at FSB 366MHz, 128KB L2 cache, 128MB
memory on board include VGA, LAN, USB 2.0, SATA, COM, CF, LPT
and Audio, RoHs
l32000-062800-RS：SATA Cable
l32200-000017-RS：FDD Cable
l19800-000400-100-RS：LPT Cable
l19800-000058-RS：RS-232/422/485 Cable

4
Jumpers Setting and Connectors
LABEL
FUNCTION
JP2 Use AT & ATX Power Select jumper
JP3 COM3 Signal jumper Setting
JP4 Serial port’s (CN21 & CN18) RI Signal Select
JP5 Flat Panel TTL (CN10) power using select
JP6 Flat Panel TTL (CN10) Clock using select
CN1
External –VCC Power Connector
CN2
Power Connector
CN3
PS-ON Connector
CN6
PWR & RST Button and Indicators panel
CN7
Inverter Connector
CN8
CPU Fan Connector
CN9
Floppy Connector
CN10
TFT LCD Connector
CN11
Primary IDE Connector (40pin 2.54mm)
CN12
Internal USB1 2.0 Connector (2 ports)
CN13
Internal USB2 2.0 Connector (2 ports)
CN14
Battery socket
CN15
IrDA Connector
CN16
10-pin Digital I/O Connector
CN17
Parallel Port Connector
CN18
Internal Serial Port (COM2/3) Connector
CN19
Audio Connector (Line out, Line in & MIC in)
CN20
Audio CD In Connector
CN21
External Serial Port (COM1) Connector
CN22
LAN Connector (RJ-45)
CN23
DB-15pin VGA Connector
CN24
Keyboard / Mouse Connector
CN25
6-pin Pin Header Keyboard/Mouse Connector
CN26
Serial ATA Connector
CN27
Serial ATA Connector
CN29
SDRAM DDR SO-DIMM socket

5
JP2: Use AT & ATX Power Select jumper
PIN NO. DESCRIPTION
Short 1 -2 Use AT Power
Open 1 -2 Use ATX Power
JP3: COM3 Signal jumper Setting
PIN NO. DESCRIPTION
Short 1 -2 RS-422
Short 2 -3 RS-485
JP4: Serial port’s CN21 Pin9 (CN18 Pin8) RI Signal Select
CONNECTOR
CN21 CN18 DESCRIPTION
Short 1 -3 Short 2 -4 12 Voltage output
Short 3 -5
Short 5 -7 Short 4 -6 Short 6 -8 5 Voltage output
Short 7 -9 Short 8 -10 Normal RI Function
JP5: Flat Panel TTL (CN10)
power using select
PIN NO. DESCRIPTION
Short 1 -2 + 3.3V
Short 2 -3 + 5V
JP6: Flat Panel TTL (CN10) Clock using select
PIN NO. DESCRIPTION
Short 1 –2
Default FPCLK
Short 2 -3 FPCLK#

6
CN19:Audio Connector (Line out, Line in & MIC in)
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1Line Out (Right)
2Line In (Right)
3GROUND 4GROUND
5Line Out (Left) 6Line In (Left)
7GROUND 8GROUND
9MIC1 In 10 MIC2 In
CN11:Primary IDE Connector
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1RESET# 2GROUND
3DATA 7 4DATA 8
5DATA 6 6DATA 9
7DATA 5 8DATA 10
9DATA 4 10 DATA 11
11 DATA 3 12 DATA 12
13 DATA 2 14 DATA 13
15 DATA 1 16 DATA 14
17 DATA 0 18 DATA 15
19 GROUND 20 N/C
21 DRQ 22 GROUND
23 IOW# 24 GROUND
25 IOR# 26 GROUND
27 CHRDY 28 (PULL LOW TO GND)
29 DACK# 30 GROUND
31 INTERRUPT 32 N/C
33 SA1 34 N/C
35 SA0 36 SA2
37 HDC CS0# 38 HDC CS1#
39 HDD ACTIVE#
40 GROUND
CN20:Audio CD In Connector
PIN NO. DESCRIPTION
1CD SIGNAL (Left)
2GROUND
3GROUND
4CD SIGNAL (Right)

7
CN8:CPU Fan
PIN NO.
DESCRIPTION
1Ground
2+5V
3Rotation Signal
CN17:Parallel Port Connector
PIN NO.
DESCRIPTION PIN NO.
DESCRIPTION
1STROBE# 2AUTO FORM FEED #
3DATA 0 4RROR#
5DATA 1 6INITIALIZE
7DATA 2 8PRINTER SELECT LN#
9DATA 3 10 GROUND
11 DATA 4 12 GROUND
13 DATA 5 14 GROUND
15 DATA 6 16 GROUND
17 DATA 7 18 GROUND
19 ACKNOWLEDGE
20 GROUND
21 BUSY 22 GROUND
23 PAPER EMPTY 24 GROUND
25 PRINTER SELECT
26 N/C
CN15:IrDA Connector
PIN NO.
DESCRIPTION
1VCC
2N/C
3IR-RX
4Ground
5IR-TX
CN13:Internal USB 2.0 Connector (2 ports)
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1VCC 2GROUND
3DATA3-4DATA4+
5DATA3+ 6DATA4-
7GROUND 8VCC
CN12: Internal USB 2.0 Connector (2 ports)
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1VCC 2GROUND
3DATA1-4DATA2+
5DATA1+ 6DATA2-
7GROUND 8VCC

8
CN24:KB/MS Connector
PIN NO.
DESCRIPTION
1KEYBOARD DATA
2MOUSE DATA
3GROUND
4+5V
5KEYBOARD CLOCK
6MOUSE CLOCK
CN21:External Serial Port Connector
PIN NO.
DESCRIPTION
1DATA CARRIER DETECT (DCD)
2RECEIVE DATA (RXD)
3TRANSMIT DATA (TXD)
4DATA TERMINAL READY (DTR)
5GROUND (GND)
6DATA SET READY (DSR)
7REQUEST TO SEND (RTS)
8CLEAR TO SEND (CTS)
9RING INDICATOR (RI)
CN25:6-pin KB/MS Connector
PIN NO.
DESCRIPTION
1+5V
2MOUSE DATA
3MOUSE CLOCK
4KEYBOARD DATA
5KEYBOARD CLOCK
6GROUND
CN18:Internal Serial Port Connector
PIN NO.
DESCRIPTION
1DATA CARRIER DETECT (DCD)
2DATA SET READY (DSR)
3RECEIVE DATA (RXD)
4REQUEST TO SEND (RTS)
5TRANSMIT DATA (TXD)
6CLEAR TO SEND (CTS)
7DATA TERMINAL READY (DTR)
8RING INDICATOR (RI)
9GROUND (GND)
10 GROUND (GND)

9
CN2:Power Connector
PIN NO.
DESCRIPTION
1+5V
2GND
3GND
4+12V
CN16:10-pin Digital I/O
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1GROUND 2+5V
3OUTPUT 0 4OUTPUT1
5OUTPUT 2 6OUTPUT3
7INPUT 0 8INPUT 1
9INPUT 2 10 INPUT 3
CN6:PWR & RST Button and Indicators Panel
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1PWRBTN 2+5V
3GROUND 4GROUND
5+5V 6RESET
7HDDLED-8GROUND
CN23:DB-15pin VGA Connector
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1RED 2GREEN
3BLUE 4N/C
5GROUND 6GROUND
7GROUND 8GROUND
9N/C 10 GROUND
11 N/C 12 DDC DAT
13 HSYNC 14 VSYNC
15 DDCCLK
CN3:PS-ON Connector
PIN NO. DESCRIPTION
1Ground
2PS-ON
3+5V Standby

10
CN1:External –VCC Power
PIN NO. DESCRIPTION
1-5V
2GROUND
3-12V
CN18:RS-422/485
PIN NO. DESCRIPTION
11 TX+
12 TX-
13 RX+
14 RX-
CN22:LAN Connectors (RJ-45)
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1TX+ 8N/C
2GROUND 9ACT_LED-
3TX-10 ACT_LED+
4RX+ 11 LINK_LED -
5GROUNG 12 LINK_LED+
6RX-13 GROUND
7N/C 14 GROUND
CN10:TFT LCD Connector
PIN NO.
DESCRIPTION PIN NO.
DESCRIPTION
1VCD_VCC 2VCD_VCC
3GROUND 4GROUND
5VCD_VCC 6VCD_VCC
7I_SDATA 8GROUND
9TFT_B0 10 TFT_B1
11 TFT_B2 12 TFT_B3
13 TFT_B4 14 TFT_B5
15 TFT_B6 16 TFT_B7
17 TFT_G0 18 TFT_G1
19 TFT_G2 20 TFT_G3
21 TFT_G4 22 TFT_G5
23 TFT_G6 24 TFT_G7
25 TFT_R0 26 TFT_R1
27 TFT_R2 28 TFT_R3
29 TFT_R4 30 TFT_R5
31 TFT_R6 32 TFT_R7
33 GROUND 34 GROUND
35 FPCLK 36 VSYNC
37 LCD_EN 38 HSYNC
39 I_SCLK 40 DISPEN

11
CN26 & CN27:
Serial ATA
PIN NO.
DESCRIPTION
1GND
2S_TXP
3S_TXN
4GND
5S_RXN
6S_RXP
7GND
CN9:Floppy Connector
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1GROUND 2DRVDEN0
3GROUND 4N/C
5GROUND 6N/C
7GROUND 8INDEX#
9GROUND 10 MOT0#-
11 GROUND 12 N/C
13 GROUND 14 DSA#-
15 GROUND 16 N/C
17 GROUND 18 DIR#
19 GROUND 20 STEP#
21 GROUND 22 WDATA#
23 GROUND 24 WGATE#
25 GROUND 26 TRK0#
27 GROUND 28 WP#
29 N/C 30 RDATA#
31 GROUND 32 HDSEL#
33 N/C 34 DSKCHG#
CN7:Inverter Power
PIN NO.
DESCRIPTION
1Ground
2Ground
3+12V
4Ground
5LCD Enable

12
Board Layout: Jumper and Connector Locations
(Unit:mm）