IEI Technology IVS-100-BT User manual

IVS-100-BT Advanced Auto Data Server
Page i
User Manual
MODEL:
IVS-100-BT
Advanced Auto Data Server with Intel
®
A
tom™ E3826 CPU,
2.0 GB DDR3L Memory, 802.11b/g/n Wi-Fi, Two GbE LAN Ports,
One HDMI Output, One VGA Output, Two SIM Card Slots,
On-board GPS, One 2.5” SATA HDD/SSD Bay, RoHS Compliant
Rev. 1.02 – May 4, 2016

IVS-100-BT Advanced Auto Data Server
Page ii
Revision
Date Version Changes
May 4, 2016 1.02 Updated storage spec
Added 3.4 Hard Disk Drive (HDD) Installation
December 30, 2015 1.01 Updated description for IVS-UHF01-R10 on page 13
May 21, 2015 1.00 Initial release

IVS-100-BT Advanced Auto Data Server
Page iii
Copyright
COPYRIGHT NOTICE
The information in this document is subject to change without prior notice in order to
improve reliability, design and function and does not represent a commitment on the part
of the manufacturer.
In no event will the manufacturer be liable for direct, indirect, special, incidental, or
consequential damages arising out of the use or inability to use the product or
documentation, even if advised of the possibility of such damages.
This document contains proprietary information protected by copyright. All rights are
reserved. No part of this manual may be reproduced by any mechanical, electronic, or
other means in any form without prior written permission of the manufacturer.
TRADEMARKS
All registered trademarks and product names mentioned herein are used for identification
purposes only and may be trademarks and/or registered trademarks of their respective
owners.

IVS-100-BT Advanced Auto Data Server
Page iv
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with limits for a class A digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on circuit different from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any change or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
Radiation Exposure Statement
This equipment complies With FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.

IVS-100-BT Advanced Auto Data Server
Page v
Table of Contents
1 INTRODUCTION.......................................................................................................... 1
1.1 OVERVIEW.................................................................................................................. 2
1.2 MODEL VARIATIONS................................................................................................... 2
1.3 FEATURES................................................................................................................... 3
1.4 FRONT PANEL............................................................................................................. 3
1.5 SIDE PANEL ................................................................................................................ 5
1.6 BOTTOM PANEL.......................................................................................................... 5
1.7 SYSTEM SPECIFICATIONS............................................................................................ 6
1.8 DIMENSIONS............................................................................................................... 8
2 UNPACKING................................................................................................................. 9
2.1ANTI-STATIC PRECAUTIONS...................................................................................... 10
2.2 UNPACKING PRECAUTIONS....................................................................................... 10
2.3 PACKING LIST............................................................................................................11
2.4 OPTIONAL ITEMS...................................................................................................... 12
3 INSTALLATION ......................................................................................................... 14
3.1ANTI-STATIC PRECAUTIONS...................................................................................... 15
3.2 INSTALLATION PRECAUTIONS................................................................................... 15
3.3 INSTALLATION AND CONFIGURATION STEPS ............................................................. 16
3.4 HARD DISK DRIVE (HDD) INSTALLATION................................................................ 16
3.5 SDHC CARD INSTALLATION .................................................................................... 18
3.6 SIM CARD INSTALLATION........................................................................................ 19
3.7 MOUNTING THE SYSTEM .......................................................................................... 21
3.8 I/O INTERFACE CONNECTORS................................................................................... 22
3.8.1 Audio................................................................................................................ 22
3.8.2 HDMI............................................................................................................... 22
3.8.3 LAN.................................................................................................................. 23
3.8.4 OBD-II (COM4)............................................................................................... 24
3.8.5 Power Input...................................................................................................... 26

IVS-100-BT Advanced Auto Data Server
Page vi
3.8.6 RS-232 COM Port (COM1, COM2) ................................................................ 27
3.8.7 RS-422/485 (COM6) & GPIO ......................................................................... 27
3.8.8 USB 3.0............................................................................................................ 28
3.8.9 Video Capture (Optional)................................................................................. 29
3.8.10 VGA................................................................................................................ 30
3.9 POWER-ON PROCEDURE........................................................................................... 31
3.9.1 Installation Checklist....................................................................................... 31
3.9.2 Power-on Procedure........................................................................................ 31
3.9.3 Power State...................................................................................................... 32
4 BIOS.............................................................................................................................. 33
4.1 INTRODUCTION......................................................................................................... 34
4.1.1 Starting Setup................................................................................................... 34
4.1.2 Using Setup...................................................................................................... 34
4.1.3 Getting Help..................................................................................................... 35
4.1.4 BIOS Menu Bar................................................................................................ 35
4.2 MAIN........................................................................................................................ 36
4.3ADVANCED............................................................................................................... 37
4.3.1 ACPI Settings................................................................................................... 38
4.3.2 Super IO Configuration ................................................................................... 39
4.3.2.1 Serial Port n Configuration....................................................................... 39
4.3.3 Hardware Monitor........................................................................................... 43
4.3.4 Power Management......................................................................................... 44
4.3.5 SMS/RTC Wake Settings................................................................................... 46
4.3.6 Serial Port Console Redirection...................................................................... 47
4.3.7 CPU Configuration.......................................................................................... 50
4.3.8 IDE Configuration........................................................................................... 51
4.3.9 USB Configuration........................................................................................... 52
4.4 CHIPSET ................................................................................................................... 53
4.4.1 North Bridge .................................................................................................... 54
4.4.1.1 Intel IGD Configuration............................................................................ 54
4.4.2 South Bridge..................................................................................................... 56
4.5 SECURITY................................................................................................................. 57
4.6 BOOT........................................................................................................................ 58
4.7 SAVE &EXIT ............................................................................................................ 60

IVS-100-BT Advanced Auto Data Server
Page vii
5 DRIVERS AND UTILITIES....................................................................................... 62
5.1 UTILITY CDAUTO RUN ........................................................................................... 63
5.2 DRIVERS................................................................................................................... 64
5.3 MOBILE AP.............................................................................................................. 65
5.3.1 Installation....................................................................................................... 65
5.3.2 Usage ............................................................................................................... 66
6 MAINTENANCE......................................................................................................... 68
6.1 SYSTEM MAINTENANCE OVERVIEW......................................................................... 69
6.2 COMPONENT REPLACEMENT PROCEDURE ................................................................ 69
6.2.1 SO-DIMM Replacement................................................................................... 70
7 INTERFACE CONNECTORS................................................................................... 72
7.1 PERIPHERAL INTERFACE CONNECTORS..................................................................... 73
7.2 INTERNAL PERIPHERAL CONNECTORS...................................................................... 74
7.2.1 5 V SATA Power Connector (SATA_PWR1)..................................................... 75
7.2.2 Audio Connector (AUDIO1)............................................................................ 76
7.2.3 Battery Connector (BT1).................................................................................. 76
7.2.4 LPC Debug Card Connector (DBG_PORT1).................................................. 76
7.2.5 PCIe Mini Card Slot for 3G Card (MINI_PCIE1)........................................... 77
7.2.6 PCIe Mini Card Slot for Wi-Fi Card (MINI_PCIE2) ...................................... 78
7.2.7 PCIe Mini Card Slot for Capture Card (MINI_PCIE3)................................... 79
7.2.8 PCIe Mini Card Slot for Capture Card or 3G Card (MINI_PCIE4)............... 80
7.2.9 Power Button and LED Connector (PWR_BTN1)........................................... 81
7.2.10 Programmer Connectors (JOBD1, JMCU1)................................................. 81
7.2.11 Reset Button Connector (RST_BTN1)............................................................ 81
7.2.12 SATA Drive Connector (S_ATA1)................................................................... 82
7.2.13 SPI Flash Connector (JSPI1)......................................................................... 82
7.2.14 USB 2.0 Connector (JUSB1).......................................................................... 82
7.3 EXTERNAL INTERFACE PANEL CONNECTORS............................................................ 83
A REGULATORY COMPLIANCE.............................................................................. 84
B SAFETY PRECAUTIONS......................................................................................... 88
B.1 SAFETY PRECAUTIONS............................................................................................. 89
B.1.1 General Safety Precautions............................................................................. 89

IVS-100-BT Advanced Auto Data Server
Page viii
B.1.2 Anti-static Precautions .................................................................................... 90
B.1.3 Product Disposal............................................................................................. 91
B.2 MAINTENANCE AND CLEANING PRECAUTIONS ........................................................ 91
B.2.1 Maintenance and Cleaning.............................................................................. 91
B.2.2 Cleaning Tools................................................................................................. 92
C OBD-II READER COMMAND ................................................................................ 93
C.1 SELECT A CHIP INITIAL MODE:UPDATE F/W OR RUN F/W.................................... 94
C.2 BOOT MODE ............................................................................................................ 94
C.3 RUN MODE.............................................................................................................. 94
C.4 INTO CAN_STANDARD V2.2.B (CAN STANDARD).................................................. 96
C.5 INTO TELEMATICS (VEHICEL INFORMATION) ........................................................... 98
D WATCHDOG TIMER .............................................................................................. 102
E HAZARDOUS MATERIALS DISCLOSURE ....................................................... 105
E.1 HAZARDOUS MATERIALS DISCLOSURE TABLE FOR IPB PRODUCTS CERTIFIED AS
ROHS COMPLIANT UNDER 2011/65/EU WITHOUT MERCURY..................................... 106

IVS-100-BT Advanced Auto Data Server
Page ix
List of Figures
Figure 1-1: IVS-100-BT Advanced Auto Data Server...................................................................2
Figure 1-2: Front Panel ..................................................................................................................4
Figure 1-3: Side View......................................................................................................................5
Figure 1-4: Bottom View ................................................................................................................5
Figure 1-5: Dimensions (unit: mm)...............................................................................................8
Figure 3-1: Bottom Panel Retention Screws..............................................................................16
Figure 3-2: HDD Bracket Retention Screw Removal.................................................................17
Figure 3-3: HDD Installation ........................................................................................................17
Figure 3-4: SDHC Card Installation.............................................................................................18
Figure 3-5: Bottom Panel Retention Screws..............................................................................19
Figure 3-6: 3G Card Retention Screws.......................................................................................20
Figure 3-7: SIM Card Socket Locations......................................................................................20
Figure 3-8: VESA Mounting Screw Holes...................................................................................21
Figure 3-9: Audio Connectors.....................................................................................................22
Figure 3-10: HDMI Connector Pinout Locations........................................................................23
Figure 3-11: RJ-45 Ethernet Connector......................................................................................24
Figure 3-12: OBD-II Connector Pinout Locations......................................................................24
Figure 3-13: OBD-II Cable and J1939/FMS Cable......................................................................25
Figure 3-14: OBD-II Connector Pinouts......................................................................................25
Figure 3-15: J1939/FMS Connector Pinouts ..............................................................................25
Figure 3-16: Power Input Connector...........................................................................................26
Figure 3-17: ACC Power Cable....................................................................................................26
Figure 3-18: Cigarette Lighter Cable (Optional) ........................................................................26
Figure 3-19: RS-232 COM Port (COM1, COM2) Pinout Locations............................................27
Figure 3-20: RS-422/485 & GPIO Connector Pinout Locations................................................28
Figure 3-21: USB 3.0 Port Pinout Locations..............................................................................29
Figure 3-22: Video Connector Pinout Locations.......................................................................29
Figure 3-23: Video Capture Cable...............................................................................................30
Figure 3-24: VGA Connector Pinout Locations.........................................................................30
Figure 3-25: Power Connector and Power Button ....................................................................32

IVS-100-BT Advanced Auto Data Server
Page x
Figure 5-1: Utility CD Menu..........................................................................................................64
Figure 5-2: Mobile AP–Connection.............................................................................................66
Figure 5-3: Mobile AP–Dial Up ....................................................................................................67
Figure 6-1: Bottom Panel Retention Screws..............................................................................70
Figure 6-2: SO-DIMM Location....................................................................................................71
Figure 6-3: SO-DIMM Installation................................................................................................71
Figure 7-1: Main Board Layout Diagram (Front Side)...............................................................73
Figure 7-2: Main Board Layout Diagram (Solder Side).............................................................74

IVS-100-BT Advanced Auto Data Server
Page xi
List of Tables
Table 1-1: Model Variations...........................................................................................................2
Table 1-2: Technical Specifications..............................................................................................7
Table 2-1: Packing List.................................................................................................................12
Table 2-2: Optional Items.............................................................................................................13
Table 3-1: HDMI Connector Pinouts ...........................................................................................23
Table 3-2: LAN Connector Pinouts.............................................................................................23
Table 3-3: OBD-II Connector Pinouts .........................................................................................24
Table 3-4: RS-232 COM Port (COM1, COM2) Pinouts ...............................................................27
Table 3-5: RS-422/485 & GPIO Connector Pinouts....................................................................28
Table 3-6: USB 3.0 Port Pinouts..................................................................................................28
Table 3-7: Video Connector Pinouts...........................................................................................29
Table 3-8: VGA Connector Pinouts.............................................................................................30
Table 3-9: Power State and Ignition System..............................................................................32
Table 4-1: BIOS Navigation Keys................................................................................................35
Table 7-1: Peripheral Interface Connectors...............................................................................75
Table 7-2: 5 V SATA Power Connector Pinouts ........................................................................75
Table 7-3: Audio Connector (AUDIO1) Pinouts .........................................................................76
Table 7-4: Battery Connector (BT1) Pinouts..............................................................................76
Table 7-5: LPC Debug Card Connector (DBG_PORT1) Pinouts ..............................................76
Table 7-6: PCIe Mini Card Slot (MINI_PCIE1) Pinouts...............................................................77
Table 7-7: PCIe Mini Card Slot (MINI_PCIE2) Pinouts...............................................................78
Table 7-8: PCIe Mini Card Slot (MINI_PCIE3) Pinouts...............................................................79
Table 7-9: PCIe Mini Card Slot (MINI_PCIE4) Pinouts...............................................................80
Table 7-10: Power Button and LED Connector (PWR_BTN1) Pinouts....................................81
Table 7-11: Programmer Connectors (JOBD1, MCU1) Pinouts ...............................................81
Table 7-12: Reset Button Connector (RST_BTN1) Pinouts......................................................81
Table 7-13: SATA Drive Connector (S_ATA1) Pinouts .............................................................82
Table 7-14: SPI Flash Connector (JSPI1) Pinouts.....................................................................82
Table 7-15: USB 2.0 Connector (JUSB1) Pinouts......................................................................82
Table 7-16: Rear Panel Connectors............................................................................................83

IVS-100-BT Advanced Auto Data Server
Page xii
BIOS Menus
BIOS Menu 1: Main.......................................................................................................................36
BIOS Menu 2: Advanced..............................................................................................................37
BIOS Menu 3: ACPI Configuration..............................................................................................38
BIOS Menu 4: Super IO Configuration........................................................................................39
BIOS Menu 5: Serial Port n Configuration Menu.......................................................................39
BIOS Menu 6: Hardware Monitor.................................................................................................43
BIOS Menu 7: Power Management .............................................................................................44
BIOS Menu 8: SMS/RTC Wake Settings .....................................................................................46
BIOS Menu 9: Serial Port Console Redirection.........................................................................47
BIOS Menu 10: CPU Configuration.............................................................................................50
BIOS Menu 11: IDE Configuration...............................................................................................51
BIOS Menu 12: USB Configuration.............................................................................................52
BIOS Menu 13: Chipset................................................................................................................53
BIOS Menu 14: North Bridge .......................................................................................................54
BIOS Menu 15: Intel IGD Configuration......................................................................................54
BIOS Menu 16: South Bridge.......................................................................................................56
BIOS Menu 17: Security...............................................................................................................57
BIOS Menu 18: Boot.....................................................................................................................58
BIOS Menu 19: Exit.......................................................................................................................60

IVS-100-BT Advanced Auto Data Server
Page 1
Chapter
1
1 Introduction

IVS-100-BT Advanced Auto Data Server
Page 2
1.1 Overview
Figure 1-1: IVS-100-BT Advanced Auto Data Server
The IVS-100-BT is an embedded system designed for in-car use. At the heart of the
system is the Intel® Atom™ E3826 processor, offering low power in a powerful package.
The IVS-100-BT supports HDMI and VGA display outputs and 802.11b/g/n wireless
networking capability. It also offers Global Position System (GPS), On-Board Diagnostic
System (OBD) technology and 3G mobile telecommunications network connection
(optional).
Other peripherals include four USB 3.0 ports, two GbE ports, one RS-422/485 and GPIO
connector, two RS-232 COM ports, optional video capture port and audio line-in and
line-out jacks.
1.2 Model Variations
The model variations of the IVS-100-BT are listed below.
Model CPU 2 GB DDR3L Memory Preinstalled
IVS-100-BT-E3/2G-R10 1.46 GHz Intel® Atom™ E3826 Yes
IVS-100-BT-R10 1.46 GHz Intel® Atom™ E3826 No
Table 1-1: Model Variations

IVS-100-BT Advanced Auto Data Server
Page 3
1.3 Features
All of the IVS-100-BT models feature the following:
Advanced auto data server with 1.46 GHz Intel® Atom™ E3826 CPU
2 GB DDR3L memory preinstalled
Built-in GPS
Optional Wi-Fi, Bluetooth and 3G network
Supports vehicle power
Optional 4-channel software compression video capture card
One SDHC card slot for data storage
Two 10/100/1000 Mbps Ethernet ports
VGA and HDMI output ports
Two SIM card slots
Two RS-232 COM ports
One RS-422/485 and GPIO connector
Four USB 3.0 ports
Audio line-in and line-out
Four RFID connectors for optional UHF RFID antenna
Supports vehicle bus protocol (OBD-II/J1939/FMS)
RoHS compliant
1.4 Front Panel
The following are found on the front panel.
1 x DC power input connector
2 x Gigabit Ethernet RJ-45 ports
1 x GPS antenna connector (COM3, COM5)
1 x HDMI connector
1 x 3G antenna connector (optional)
1 x Line-out jack
1 x Line-in jack
1 x OBD-II connector (COM4)
1 x Power button
2 x RS-232 COM ports (COM1, COM2) (DB-9)

IVS-100-BT Advanced Auto Data Server
Page 4
1 x RS-422/485 (COM6) and GPIO connector
1 x VGA connector
1 x Video capture connector (optional)
2 x Wi-Fi and Bluetooth antenna connectors (optional)
4 x UHF RFID antenna connectors (optional)
4 x USB 3.0 ports
Figure 1-2: Front Panel

IVS-100-BT Advanced Auto Data Server
Page 5
1.5 Side Panel
The left side panel has an SDHC card slot for SD storage card installation (Figure 1-3).
Figure 1-3: Side View
1.6 Bottom Panel
The bottom panel has VESA mounting screw holes for mounting.
Figure 1-4: Bottom View

IVS-100-BT Advanced Auto Data Server
Page 6
1.7 System Specifications
The IVS-100-BT technical specifications are listed in Table 1-2.
System
CPU 1.46 GHz Intel® Atom™ E3826 (dual-core, 1MB cache, TDP=7W)
Memory 2 x 204-pin 1067 MHz DDR3L SO-DIMM slots (preinstalled with 2 GB
memory for IVS-100-BT-E3/2G-R10)
Storage
1 x 2.5” SATA 6Gb/s HDD/SSD bay
1 x SDHC card slot (system max. 32 GB)
1 x mSATA slot (SATA 3Gb/s)
OS Windows® Embedded Standard 7 E
Communication
Ethernet 2 x GbE RJ-45
Wireless LAN PCIe Mini, 802.11b/g/n, 1T1R Wi-Fi module (optional)
Bluetooth Bluetooth v2.0 (integrated with WWAN)
WWAN+Bluetooth PCIe Mini, WCDMA/HSDPA/HSUPA+Bluetooth module (optional)
2 x SIM card slots (support Bluetooth voice)
GPS On-board GPS module
Data Collection
RFID 4 x UHF RFID connectors for optional UHF RFID antenna
Video Capture Optional 4-channel software compression video capture card
(max. 8 channels)
Connectors and Buttons
Antenna Connectors
1 x GPS antenna connector
1 x WWAN antenna connector (optional)
4 x UHF RFID antenna connectors (optional)
2 x Wi-Fi and Bluetooth antenna connectors (optional)
I/O Ports
1 x 9 V ~ 30 V DC power input connector with ACC control
2 x Gigabit Ethernet RJ-45 ports
1 x HDMI connector
1 x Line-in jack
1 x Line-out jack
1 x OBD-II connector (COM4)
1 x Power button with LED

IVS-100-BT Advanced Auto Data Server
Page 7
2 x RS-232 COM port (COM1, COM2) (DB-9)
1 x RS-422/485 (COM6) and GPIO connector (DB-15)
1 x SDHC card slot
1 x Video capture connector (optional)
1 x VGA connector (resolution: up to 2560x1600@60Hz)
4 x USB 3.0 ports
Power
Power Input 9 V ~ 30 V DC input with ACC control
Cigarette lighter power or ACC power
Environmental and Physical Specifications
Mounting VESA 100 mm x 100 mm
Dimensions (WxDxH) 200.0 mm x 155.0 mm x 76.6 mm
Weight (Net/Gross) 2.1 kg/3.6 kg
Operating
Temperature -20ºC ~ 60ºC (with air flow)
Storage Temperature -30ºC ~ 70ºC
Humidity 5% ~ 95% (non-condensing)
Operating Shock Half-sine wave shock 5 G, 11 ms, 3 shocks per axis
Operating Vibration MIL-STD-810F 514.5C-2 (with SSD)
Safety CE, FCC, e-MARK
Table 1-2: Technical Specifications

IVS-100-BT Advanced Auto Data Server
Page 8
1.8 Dimensions
The dimensions are shown below.
Figure 1-5: Dimensions (unit: mm)