IKEA TORNVIKEN User manual

1
TORNVIKEN
INSTRUCTION MANUAL
Keep this information for further reference
Céline SELLIER, Master CAWEB (2021)

2
INSTRUCTION MANUAL.........................................................................................................................1
INTRODUCTION.....................................................................................................................................3
Important Safety Instructions ............................................................................................................4
Warning : fastening devices not included ..........................................................................................4
Tips before you start .........................................................................................................................5
Tips............................................................................................................................. 5
Essentials.................................................................................................................... 5
ASSEMBLY .............................................................................................................................................6
Parts listing........................................................................................................................................7
Structure..................................................................................................................... 7
Screws and fixings ...................................................................................................... 7
Step 1................................................................................................................................................8
Step 3................................................................................................................................................9
Step 3................................................................................................................................................9
Step 4..............................................................................................................................................10
Step 5..............................................................................................................................................11
Step 6..............................................................................................................................................12
Step 7..............................................................................................................................................13
Step 8..............................................................................................................................................14
Step 9..............................................................................................................................................14
Step 10............................................................................................................................................15
Step 11............................................................................................................................................16
Step 12............................................................................................................................................16
Step 13............................................................................................................................................17
Step 14............................................................................................................................................18
TIPS: BEST FASTENING DEVICE.............................................................................................................19
Step 1..............................................................................................................................................20
Step 2..............................................................................................................................................20
Summary

3
INTRODUCTION
Important information: read carefully

4
Assembly should be carried out by a qualified person: wrong
assembly may lead to the furniture falling down and causing
injury or damage
Serious or fatal crushing injuries can occur from furniture
falling down
To prevent this furniture from falling down it must be
permanently fixed to the wall with a non-included wall
attachment devices
Fastening devices for the wall are not included since
different wall materials require different types of fastening
devices
Use fastening devices suitable for the walls in your home
Assess the suitability of the wall to ensure that the
fastening devices will withstand the forces generated
For advice on suitable fastening devices, contact your local
specialized dealer
Important Safety Instructions
Warning : fastening devices not included

5
Tips
1. For ease and speed of assembly, please check that all parts
are present before you start the assembly of your furniture
2. Please ensure that you have sufficient space and people (as
indicated below) to assemble your product safely
3. Always place the product on a flat, steady and stable surface
4. We recommend that you assemble the product as near as
possible to the area in which it will be placed in use, to avoid
moving the product unnecessarily once assembled
5. Please use caution and care when lifting the product to avoid
personal injury and/or product damage
Essentials
You will need :
-A flathead screwdriver
-A crosshead screwdriver
-A carpenter’s level
2-Person Assembly
To prevent any damage, please place
the product on a protected surface
during assembly
Should anything be unclear
Do not hesitate to contact Ikea
Customer Service
Tips before you start

6
ASSEMBLY
Follow each step of the instruction carefully

7
Structure
Screws and fixings
Flat Head Socket
Screws x 4
Ikea Cam Bolt x 10
Cam Lock x 10
Wood Dowels x 22
Pan Head Self Tapping
Screws x 4
Phillips Mod Truss Self
Piercing Screws x 2
Allen Wrench x 1
Parts listing
Left side panel
Right side panel
Bottom panel
First inner panel
Second inner panel
Top panel
Support board
Back panel

8
Instructions:
Place Left Side Panel (A) and Right Side Panel (B) on a flat
covered area with the holes facing up
Insert the 10 supplied Cam Bolt into the pre-threaded holes
as shown (5 on each panel)
Screw them in by using a crosshead screwdriver
Caution:
Tighten only until snug. Do not over-tighten.
Step 1
You will need :
B
A

9
Instructions:
Insert 2 wood dowels into the Left Side Panel (A) holes
(bottom of the panel)
Carefully push the Bottom Panel (C) onto the dowels
Insert 2 wood dowels into the Bottom Panel (C) holes
Step 2
You will need :
C
Bottom Panel
A
Left Side Panel
Step 3
You will need :
A
Left Side Panel
C
Bottom Panel
D
First Inner Panel

10
Instructions:
Insert 2 wood dowels into the Left Side Panel (A) holes (top
of the panel)
Carefully push the First Inner Panel (D) onto the dowels
Insert 2 wood dowels into the First Inner Panel (D) holes
Caution:
Make sure the bevelled edges of the First Inner
Panel (D) will ultimately face the room and not
the inside of the furniture.
Instructions:
Insert the 4 Cam Locks into the large holes underneath the
Bottom Panel (C) and the First Inner Panel (D) (2 holes
under each panel)
Step 4
You will need :
4x
A
Left Side Panel
C
Bottom Panel
D
First Inner Panel

11
Please, notice the Cam Lock has a "C" -Shaped back. Insert
the Cam Lock so the opening of the "C" fits over the head
of the Cam Bolt
Use a flat screwdriver to turn the Cam Lock clockwise on
half a turn so it locks onto the head of the Cam Bolt
Caution:
Turn only until it is snug - over-tightening could cause the
Cam to bend or break.
Instructions:
Insert 3 wood dowels into the Left Side Panel (A) holes
(middle of the panel)
Carefully push the Second Inner Panel (E) onto the dowels
Insert 3 wood dowels into the Second Inner Panel (E) holes
Caution:
Make sure the bevelled edges of the Second Inner
Panel (E) will ultimately face the room and not
the inside of the furniture.
Step 5
You will need :
6x
A
Left Side Panel
D
First Inner Panel
C
Bottom Panel
E
Second Inner Panel

12
Instructions:
Insert 2 wood dowels into the Left Side Panel (A) holes (top
right of the panel)
Carefully push the Support Board (F) onto the dowels
Insert 2 wood dowels into the Support Board (F) holes
Caution:
Make sure the bevelled side of the Support
Board (F) faces the First Inner Panel (D)
Step 6
You will need :
4x
A
Left Side Panel
F
Support Board
D
First Inner Panel

13
Instructions:
Insert the Cam Lock into the large hole on the Support
Board (F) (the closest hole to the floor)
Please, notice the Cam Lock has a "C"-shaped back
Insert the Cam Lock so the opening of the "C" fits over the
head of the Cam Bolt
Use a flat screwdriver to turn the Cam Lock clockwise on
half a turn so it locks onto the head of the Cam Bolt
Caution:
Turn only until it is snug - over-tightening could cause the
Cam to bend or break.
Step 7
You will need :
1x
F
Support Board

14
Instructions:
Lift, turn and align the Right Side Panel (B) over the wood
dowels
Carefully push the Right Side Panel (D) onto the dowels
Step 8
Right Side Panel
Step 9
Right Side Panel
F
Support Board
F
Support Board
G
Back Panel

15
Instructions:
Slide the Back Panel (G) into the notches provided
Caution:
Make sure the plain side of the Back Panel (G) will
ultimately face the wall
Instructions:
Insert the Cam Locks into the large holes on the Support
Board (F), the Back Panel (G) and the Right Side Panel (B)
(5 in total as shown above)
Please, notice the Cam Locks have a "C"-shaped back
Insert the Cam Locks so the opening of the "C" fits over the
head of the Cam Bolt
Use a flat screwdriver to turn the Cam Locks clockwise on
half a turn so it locks onto the head of the Cam Bolts
Caution:
Turn only until it is snug - over-tightening could cause the
Cam to bend or break.
Step 10
You will need :
5x
Right Side Panel
F
Support Board
G
Back Panel

16
Instructions:
Insert 2 wood dowels into the Left Side Panel (A) holes
(upper edge)
Insert 2 wood dowels into the Right Side Panel (F) holes
(upper edge)
Step 11
You will need :
4x
Left Side Panel
Right Side Panel
Step 12
F
Support Board
H
Top Panel
G
Back Panel
1

17
Instructions:
Lift, turn and align the Top Panel (H) over the wood dowels
Carefully push the Top Panel (H) onto the dowels
Caution:
Make sure you turn the Top Panel (H) so that the notch (1)
is on the side of the Support Boad (F) and fits together with
the Back Panel (G)
Instructions:
Insert the 4 Flat Head Socket Screws in the provided holes
on the Top Panel (H) (1 for each corner)
Tighten the screws with the Allen Wrench
Step 13
You will need :
H
Top Panel

18
Instructions:
Insert the 4 Pan Head Screws in the provided holes on the
Back Panel (H) (1 for each corner)
Tighten the screws with the crosshead screwdriver
Caution:
Make sure you take and use Pan Head Screws.
Please, do not confuse them with Phillips Mod
Truss Screws.
Step 14
You will need :
G
Back Panel

19
TIPS: BEST FASTENING DEVICE
Please remember: fastening devices are not
included

20
Instructions:
Place a French cleat against your wall. Please note : a
French cleat is a coving with a 30–45 degree slope used to
hang cabinets or other objects
Position a carpenter’s level where you want the bottom of
the cleat on your wall, and draw a line along the level’s top
edge
Screw the French cleat to the wall with 2 Round-Head
Slotted Wood Screws and with its bevelled edge facing up
Step 1
You will need :
Step 2
You will need :