IKEA TREDANSEN User manual

TREDANSEN

English 4
Français 11
Español 19

4
English
IMPORTANT
SAFETY
INSTRUCTIONS
Read all instructions before using
the product.
DANGER
To reduce the risk of electric shock:
Always unplug this product from the
electrical outlet before cleaning.
Do not allow children to play with xed
controls. Keep remote controls away
from children.
Follow all instructions, since incorrect
installation can lead to severe injury.
This appliance can be used by children
aged from 8 years and above and
persons with reduced physical, sensory
or mental capabilities or lack of
experience and knowledge if they have
been given supervision or instruction
concerning use of the appliance in a
safe way and understand the hazards
involved by a person responsible for
their safety. Children shall not play with
the appliance.
Cleaning and user maintenance shall
not be made by children without
supervision.
SAVE THESE
INSTRUCTIONS.
This package includes one wireless
blind (1), one remote (2), one signal
repeater (3), one power supply unit (4)
and one battery pack (5).
These products are already paired to
each other, so you only need to connect
the power supply unit to the signal
repeater and then to a nearby wall
socket. Then mount the blind to your
window frame and insert the battery
pack to get started.
Blind (1)
Remote (2)
Signal repeater (3)
Power supply unit (4)
Battery pack (5)

5
Instructions for use
Connect the power supply unit into the
wall socket, insert the signal repeater
into the free slot.
When charging, only use recommended
USB cables for your device and replace
faulty cables immediately.
Remote functions
Up:
Press to raise your wireless blind.
Down:
Press to lower your wireless blind.
Pairing: Used to add IKEA Home
smart products to your system.
IMPORTANT: The signal repeater needs
to be plugged in and powered to be
able to control your blind with the
remote!
Signal repeater function
With TRÅDFRI signal repeater you can
expand the signal reach of your IKEA
Home smart products.
Using your wireless blind
To raise blind to top position:
Press the up button once (short press)
on the remote or on the blind.
To lower blind to bottom position:
Press the down button once (short
press) on the remote or on the blind.
To raise the blind:
Press and hold the up button on the
remote or on the blind.
While pressing the button, the blind
will rise. Release the button once the
desired height or maximum height is
reached.
To lower the blind:
Press and hold the down button on the
remote or on the blind.
While pressing the button, the blind
will lower. Release the button once
the desired height or the maximum
extension is reached.
Setting desired minimum height:
Only the buttons on the blind can be
used to set this level.
Move the blind to the desired height.
Afterwards, short press either the up
or down button on the blind twice to
save this position as the new minimum
height.
The blind will move slightly up and
down to conrm the setting.
Resetting minimum height:
To change the minimum height or
revert to the default minimum height
setting, rst move the blind to the top

6
position. Afterwards, press either the
up or down button on the blind twice.
The blind will move slightly up and
down to conrm the setting.
Repeat the above steps to set a new
desired minimum height.
Correcting unbalanced blind
If the blind gets stuck when lowering, it
might become unbalanced.
Raise the blind completely to level it
again.
Adding devices to your remote
Pairing: Used to add IKEA Home
smart products to your system.
> 10 s
Follow these steps to add more wireless
blinds to your system. Make sure that
your wireless blind is turned on.
1. Open the back cover of the remote
and nd the pairing button.
2.Short press both buttons on the blind.
This will wake up the device and it is
ready for pairing for 2 minutes.
3.Hold the remote close to the wireless
blind you want to add: no more than
5 cm away from (1).
4.Press and hold the pairing button on
the remote for at least 10 seconds.
5.A red LED light will illuminate on
the remote. On your wireless blind,
a white LED light will begin to dim
and ash until the devices have been
successfully paired.
Up to 10 wireless blinds can be paired
with 1 remote.
Make sure to pair one blind at a time.
If you have diculties pairing multiple
blinds, temporarily disconnect those
that have already been paired by
disconnecting the battery pack inside
the blind. This will help with the pairing
process.
Changing the remote’s battery
When the remote is used regularly and
as intended, the battery will last for
approximately 2 years.
When it’s time to replace the battery,

7
a red LED light will ash when you use
the remote.
Open the rear cover and replace the
battery with a new CR2032 battery.
WARNING!
Risk of explosion if battery is replaced
by an incorrect battery type. Dispose
of used batteries according to the
instructions.
Charging the battery pack
The included battery pack for wireless
blind can be charged through the signal
repeater unit.
Use the included USB cable for
charging.
Upon normal use, the battery pack
should be charged every 6 months.
A LED indicator on the battery pack will
display the status.
LED indicator status:
Charging in progress: LED on.
Charging complete: LED o.
Error: LED ashes.
Factory reset your devices
After resetting the signal repeater,
you must pair the remote to the signal
repeater and then pair the remote to
the wireless blind again.
Signal repeater:
Push a pin into the pinhole on bottom
of the signal repeater for at least 5
seconds.
Remote:
Press the pairing button 4
times within 5 seconds. A red
LED light will ash, indicating
that it has been reset.
Wireless blind:
Press and hold both buttons for 5
seconds.
A white LED light will ash 4 times,
indicating the blind has been reset.
Good to know
• The power supply unit can be used
to charge the wireless blind’s battery
pack.
• USB cable length and quality
inuences the charging speed and
performance.

8
• Devices may become warm during
charging. This is completely normal
and they will gradually cool down
again after they are fully charged.
• Unplug the power supply unit from
the wall socket before cleaning and
when it is not in use.
• The battery pack should not be left
discharged for a longer period of
time.
• The battery pack should not be
charged while in contact with
ammable materials like textiles.
• This battery pack can only be used
with IKEA products.
IMPORTANT!
Wireless blind package:
• The included devices are for
indoor use only and can be used in
temperatures ranging from 0ºC to
40ºC (32ºF to 104ºF).
• Storage temperature: -20°C to 25°C
(4°F to 77°F).
• Do not leave any device in direct
sunlight or near any heat source,
since it may overheat.
• The range between the transmitter
and the receiver is measured in open
air.
• Dierent building materials and
placement of the units can aect the
wireless connectivity range.
WARNING:
Power supply unit:
• The wall socket must be located near
the equipment and must be easily
accessible.
• If any device is damaged, it should not
be used and should immediately be
disposed of.
• Do not subject the units to wet, moist
or excessively dusty environments
since this can cause damage to the
units.
• Never use a damaged or faulty USB
cable for charging, since this can
damage the product and harm your
device.
• Recommended precautionary
measures and technical data, see the
back of the power supply unit.
WARNING
Battery pack:
• Do not modify, disassemble, open,
drop, crush, puncture, or shred the
battery.
• Do not expose the battery to rain or
water.
• Risk of res and burns. Do not subject
the battery to a temperature over
60°C (140ºF) and do not incinerate the
battery.
• Keep the battery away from open
ames or sunlight to prevent heat
build-up.
• Keep the battery away from high
voltage devices.
• This product is not a toy, keep away
from children. Ensure that all persons
who use this product read and follow
these warnings and instructions.
• Do not short-circuit the battery or its
cells.
• In the event of a battery cell leaking,
do not allow the liquid to come in
contact with the skin or eyes.

9
Product servicing
Do not attempt to repair these products
yourself, since opening or removing
covers may expose you to dangerous
voltage points or other risks.
Technical data
Type: E2103
TREDANSEN
E1746 wireless
signal repeater
E1766 Open/Close
remote
Input: 7.2V DC, 2.0A 5.0V DC, 1.0A 3.0V, CR2032
battery
Range: 10 m in open air
For indoor use only
Operating
frequency: 2400-2483.5 MHz
Output power: 9.6 dBm (EIRP) 9.6 dBm (EIRP) 7.3 dBm (EIRP)
Power supply unit
Type: ICPSW5-5NA-1
Input: 100-240 VAC, 50/60 Hz, 0.2A
Output: 5.0V DC
Max total load: 1.0A, 5.0W
Battery pack
Model: BRAUNIT battery pack
Type: ICBL7.2-18-USB-A1
Capacity: 2600mAh/18.72Wh
Input:
5.0V DC, 1.0A (Micro USB)
8.4V DC, 2.0A (4 pin connector)
Output: 7.2V DC, 2.0A
Rechargeable Li-Ion battery cell
inside.
Indoor use only
RF EXPOSURE INFORMATION
According to RF exposure regulations,
under normal operations the end user
shall refrain from being closer than 20
cm from the device.
Manufacturer: IKEA of Sweden AB
Address:
Box 702, SE-343 81 Älmhult, SWEDEN
License rights and limitations
NO RIGHTS OR LICENSES, EXPRESS
NO RIGHTS OR LICENSES, EXPRESS OR
IMPLIED, ARE GRANTED TO USE THIRD-
PARTY DEVICES IN COMBINATION
WITH THESE PRODUCTS IN A WIRELESS
MESH NETWORK, OR TO USE THIRD-
PARTY SERVICES TO ACCESS, MONITOR
OR CONTROL THESE PRODUCTS IN
A WIRELESS MESH NEWORK VIA THE
INTERNET OR ANOTHER EXTERNAL
WIDE AREA NETWORK.
For use pursuant to U.S. Patent Nos.:
US 6,914,893
US 7,697,492
US 8,964,708

10
This device complies with Part 15 of the
FCC Rules.
This device contains licence-exempt
transmitter(s)/receiver(s) that comply
with Innovation Science and Economic
Development Canada's licence-exempt
RSS standard(s).
Operation is subject to the following
two conditions:
(1) this device may not cause harmful
interference, and
(2) this device must accept any
interference received, including
interference that may cause
undesired operation of the device.
WARNING:
Any changes or modications to this
unit not expressly approved by the
party responsible for compliance could
void the user’s authority to operate the
equipment.
NOTE:
This equipment has been tested and
found to comply with the limits for
a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits
are designed to provide reasonable
protection against harmful interference
in a residential installation.
This equipment generates, uses and
can radiate radio frequency energy
and, if not installed and used in
accordance with the instructions, may
cause harmful interference to radio
communications. However, there is no
guarantee that interference will not
occur in a particular installation.
If this equipment does cause harmful
interference to radio or television
reception, which can be determined
by turning the quipment o and on,
the user is encouraged to try to correct
the interference by one or more of the
following measures:
• Reorient or relocate the receiving
antenna.
• Increase the separation between the
equipment and receiver.
• Connect the equipment into an outlet
on a circuit dierent from that to
which the receiver is connected.
• Consult the dealer or an experienced
radio/TV technician for help.
The crossed-out wheeled bin symbol
indicates that the item should be
disposed of separately from household
waste. The item should be handed in
for recycling in accordance with local
environmental regulations for waste
disposal. By separating a marked item
from household waste, you will help
reduce the volume of waste sent to
incinerators or land-ll and minimize
any potential negative impact on
human health and the environment. For
more information, please contact your
IKEA store.