Ikon IK40 User manual

Installation and User Manual
For models:
IK40, IK41, IK73, IK74, IK77 & IK78
MODEL
COOKER HOOD
INSTRUCTIONS MANUAL
1170 - 1172 1171
1170 - 1171
1172 - 1173
1173
MODEL
COOKER HOOD
INSTRUCTIONS MANUAL
1170 - 1172 1171
1170 - 1171
1172 - 1173
1173
IK40 & IK41
IK73, IK74, IK77 & IK78

-2-
INTRODUCTION OF DEVICE
1170 - 1172 1171
530
310
135
238
30
500
270
199
245
790
310
135
238
30
750
270
199
245
1170 - 1171
60 cm
1170 - 1171
90 cm
247
260
295
598
568.5
270
32
237
1172
60 cm
247
260
295
898
853
270
32
327
1172
90 cm
11
2
33
2
1) Control Panel
2) Cooker Lighting
3) Aluminum Cassette Filter
1173
1
2
3
247
261
310
506
530
21
252.5
247
730
790
47
250
261
295
1173-60
1173-90
IK40 IK41
IK78
IK73 & IK77
IK74 & IK78
IK73 example
310
-2-
INTRODUCTION OF DEVICE
1170 - 1172
1171
530
310
135
238
30
500
270
199
245
790
310
135
238
30
750
270
199
245
1170 - 1171
60 cm
1170 - 1171
90 cm
247
260
295
598
568.5
270
32
237
1172
60 cm
247
260
295
898
853
270
32
327
1172
90 cm
1
1
2
3
3
2
1) Control Panel
2) Cooker Lighting
3) Aluminum Cassette Filter
1173
1
2
3
247
261
310
506
530
21
252.5
247
730
790
47
250
261
295
1173-60
1173-90
IK40 example

-3-
*Before you take pot, fry-pan etc. from the
hob, put their lids on.
*Do not leave hot oil on the hob. Pots that
have hot oil in them may cause selfignition.
*Pay attention to curtains and covers during
cooking of meals like frying because oil may
flare up.
*Make sure that filters are changed in
convenience. Filters that are not changed at
appropriate time has risk of causing fire due
to oil that will be gathered on them.
*Do not use filter materials that are not flame
resistant instead of filter.
*Do not operate your product without
aluminum filter; do not remove filters when
the product is on.
*In case of flame, cut power of the product
and the cooking appliances. (Cut power of
the product by plugging it off the socket).
*Your product may cause fire risk if cleaning
is not applied periodically.
*Cut power of the product before
maintenance process. (Cut power of the
device by unplugging it)
*When chimney hood and the appliances
working with energy other than electricity
are operated at the same time, negative
pressure in the room should not be more
than 4 Pa (4 x 10 bar)
*If there is an appliance working with fuel or
gaseous fuel at the same place with your
hood, this appliance's exhaust should be
isolated from its volume totally and the
appliance should be hermetic type.
*When chimney connection is applied to
your product, use ducts of 150mm or
120mm diameter. Duct connection should
be as short as possible and should include
few bends.
*This product is designed for usage at
home.
*Your products usage voltage is 220-240
Volts~50Hz
*Grounded plug is used at your product's
electric network cable. This cable should
definitely be plugged in a grounded socket.
*All electrical networks should be set by a
qualified electrician.
*Installation applied by unauthorized
people may cause the product to operate at
low performance, damage of the product
and accidents.
*Power supply cable should not be exposed
to press
or smash during montage. Network
cordon should not be placed near the
cookers; it may cause fire if it melts.
*Do not plug into the socket before
installation of the product is completed.
*Keep the plug at a reachable place so that
you can unplug it in case of any danger.
*Do not touch the lamps when they are on
for long time. Lamps may hurt your hand as
they will be hot.
*Kitchen cooker hoods are designed for
usage during normal and home-style
cooking. If it is used for other purposes,
failure risk occurs and it will be out of
warranty.
*Follow applicable rules and directions for
passing out outlet air. (This warning is not
valid for usage without chimney.)
*Flaming foods should not be cooked under
the product.
*Start your product after you put pot, fry-pan
etc. on the hob. Otherwise high
temperature may cause some parts of your
product to get deformed.
-5
WARNINGS AND SAFETY PRECAUTIONS

-4-
*Keep package materials away from
children as they may be dangerous for
them.
*Be sure that your child does not play with
the product. Do not allow kids to use your
product.
*If power supply cable is damaged, this
cable should be changed by its producer or
its service agency or a personnel who is a
specialist at the same level in order to
prevent a dangerous situation.
Warning about Transportation and Carriage
*All the materials used at package of your product are suitable for recycling.
*Please comply with the signs on the product's box during transportation.
*Hold the holders placed at sides of the box in order to carry your product.
If you need transportation;
*Keep the original box.
*Carry your product in its original box; comply with the carrying signs on the product's box.
If there is no original package;
*Do not put heavy material on the chimney hood.
*Keep the external surface from bash.
*Pack your product to avoid damages.
Installation, taking off your product from its package:
*Check if there is any deformation on your product.
*Transportation damages and failures should immediately be reported to the transportation
responsible.
*If you notice any damage please report to the seller.
*Do not allow children to play with packing material!!!
*In case of flame, cut power of the cooker
hood and the cooking appliances, cover the
flame. Never use water in order to
extinguish it.
Use “MAX 6 A” fuse at cooker hood
installment for your security.
“CAUTION: Accessible parts may become hot when used with cooking appliances”
''The appliance is not to be used by children or persons with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have
been given supervision or instruction''
-13-
FUSE
ELECTRONIC CIRCUIT
CAPASITOR
5 µf/400 V
M
FUSE
800m³/h 5 Speed
FUSE
10 10
10
M
CAP
CAP
N M1 M2 M3 M4
M5
LAMP
500 m³/h 3 Speed
FUSE
CONTROL PANEL
ELECTRONIC CIRCUIT
M
INPUT : 220 - 240 V AC / 50 Hz
WHITE
WHITE
LAMP
BLACK
BLUE RED
WHITE
BROWN
YELLOW/GREEN
BLUE
800 m³/h 3 Speed
CONTROL PANEL
LAMP
WHITE
WHITE
BLACK
WHITE
BLUE
RED
BROWN
BROWN
YELLOW/GREEN
BLUE
INPUT : 220 - 240 V AC / 50 Hz
LAMP
BLACK
GREY
YELLOW
WHITE
BLUE
BROWN
RED
GREY
GREY
BROWN
YELLOW/GREEN
BLUE
WHITE WHITE
WHITE
WHITE
ELECTRONIC CIRCUIT
BUTTON BOX
5µF
YELLOW-GREEN
(1)
(2)
(3)
YELLOW/GREEN
Eco 3 Speed

-12-
Standard Accessories
Plastic Outlet (Figure 1)
Plastic outlet mounted to air outlet of the cooker hood
Min.65 cm
Min.75 cm
Place of the Product:
After installation of your product, distance between
range hood and electrical hob should be at least 65
cm and gas hobs at least 75cm. Figure 2
Installation, taking off your product from its package:
*Check if there is any deformation on your product.
*Transportation damages and failures should immediately be reported to the transportation
responsible.
*If you notice any damage please report to the seller.
*Do not allow children to play with packing material!!!
Figure 1
Figure 2
Figure 3
Screwing the plastic vent.
Before installing the hood into the cabinet, screw the
plastic vent.
3,5 x 9,5 RYSB
Screws
COOKER HOOD MOUNTING
If the product does not work:
Before you contact the technical service:
Make sure that the product is plugged in and the electric fuse of the electric wiring is running. Do
not take any action that will damage the product. Before you contact with technical service, check
your cooker hood according to Table 1. If the problem goes on, contact the seller or the most
authorized service.
Check electric connection(Voltage of the
electric network should be between 220-240V,
cooker hood should be connected to grounded
Check motor switch (Motor switch should be at
on position) Check motor switch (Motor switch should be at
on position) Check aluminum filter(Aluminum Cassette Filter should be washed once a month at normal conditions.)
Check lamps(Lamps should be firm.)
Check outlet (Outlet should be open) Check Carbon Filter (Carbon filter should be replaced with a new one each 2-3 months at the
models with Carbon Filter at normal
conditions)
Cooker-hood does not work
Illumination Lamp does not work
Cooker-hoods air suction is weak
Cooker-hood does not direct air out
(at places without chimney)
In order to use the cooker hood efficiently;
*Use ducts of 150/120mm diameter and as few bends as possible when you make the chimney
connection.
*Pay attention to aluminum filters' cleaning periods and changing periods of carbon filters.
*Use the product at middle speed if high suction power is not necessary.
* In order to ensure that ventilation occurs correctly, windows of the kitchen should be kept
-5-
Min 65cm
Max 75cm

-6-
Ø 3 mm
WARNING : During drilling the hanging holes , please pay attention to the diameter of the
holes to be used for hanging the hood.
If the diameters of hanging holes are not as pointed , the hood can not be assembled properly.
Installation of the aluminum duct
Connect one end of the aluminum vent to the previously
mounted plastic vent.
Connect the other end of the aluminum vent to kitchen
chimney. Make sure that said two connection are not
disconnected under maximum hood speed (Figure 4).
Figure 4
Drilling suspension holes
For Model 1170 - 1171- -1173 / 60
By using a Ø3mm driller, drill points marked as A, B, C, D
in mounting scheme.
For Model 1170 - 1171 - 1173 / 90
By using a Ø3mm driller, drill points marked as A, B, C, D,
E, F in mounting scheme.
For Model 1172 - 60
By using a Ø3mm driller, drill points marked as A, B, C,
D,E,F in mounting scheme.
For Model 1172 - 90
By using a Ø3mm driller, drill points marked as A, B, C,
D,E,F,G,H in mounting scheme.
Mounting into cabinet
Place the hood into the cabinet (Picture 5).
Align holes drilled according to mounting scheme and
holes on the product panel, and fix the product.
(Figure 6).
Mounting
holes
MAINTENANCE
*Disconnect electricity connection before maintenance and
cleaning process.
*Aluminum cassette filter holds the dust and the oil in the air.
*Metal filter should be washed once in a month with hot and
soaped water or, if possible, at dishwasher (60C).
*Take off aluminum cassette filter pressing on springy
latches on end point. After cleaning, do not replace before it
dries.
*Outer surface of the cooker hood should be wiped with a
wet cloth that is wetted with water or alcohol.
*Please avoid contact of electronic parts with water or
similar materials.
*Using Inox cleaning and maintenance products available in
the market will help your product to perform longer.
Warning: Aluminum filters may be washed in the
dishwasher. Color of aluminum filters may change after
several washings. This is normal and it is not necessary to
change the filters.
Efficient Ventilation
In order to ensure correct ventilation, keep your kitchen windows closed.
IMPORTANT NOTE
Please pay attention when the product is operated at the same time with a product which operates
using air and fuel (for instance; heater, water heater etc. which operates using gas, diesel fuel,
coal or wood), since cooker hood may affect burning negatively as it directs the air out.
This warning is not valid for usage without chimney.
Washable Aluminum
Cassette Filter
-11-

-7-
Replacing the Lamps
Cut off the connection of the cooker hood with electricity. Take off the aluminum cassette filter.
Take off the failed lamp and replace it with a new one that is of the same rating. (Please wait for the
lamps to cool as they might hurt your hand.)
Replacing 50W Halogen Lamp
In order to change halogen lamps, take the lamp downwards
pushing back of lamp holder downwards and then turning it a
little bit anti-clockwise take it off downwards. Figure 14
Functions of the Product
Your hood is compatible for use with our without chimney.
Usage with chimney
The product should be connected to a chimney that will direct the air out during usage with
chimney. In order to achieve best performance, pay attention that the duct system follows the
shortest way for connection to the chimney. Your product is produced as it will be appropriate for
usage with chimney.
Attention!!!
Outlet of the product should not be connected to air canals that have other smoke as well.
Active Carbon Filter
To provide air recirculation where product's chimney air outlet cannot be connected to exterior,
it is necessary to use active carbon filter with your product. You may purchase this accessory
from authorized sellers and after sales services
Figure 14
Replacing bulb
In order to change the bulb, turn it anti-clockwise and take it off.
Replace it with a new one in the same value by turning it in
clockwise. Figure 16
Figure 16
-10-
Illumination
The product has 2 lamps and one lamp button to operate illumination. Press lamp button in
order to start illumination.
Usage of 5 Speed Digital Control
Usage
Remove protective folio on the inox product after installation.
Speed Selection The product has 5 speeds of ventilation level. One of 1,2,3,4,5 speeds is
selected in accordance with steam of cooking or fry. Motor is started pressing control button
on the front panel. Speed is increased pressing button, and decreased by pressing button.
Automatic timer (TIMER) is available at the models with electronic remote control. When you press
button more than 2 seconds, timer function will be on for 15 minutes. When the timer is on,
Display will signal and the motor will be off automatically 15 minutes later. Please use the cooker
and the product at the same time to enable circulation. Doing so, air suction power will be affected
positively. We recommend you to operate your product for few minutes more after the cooking is
completed to enable absorption rest of smell and steam.
Cleaning Periods of the Aluminum Filters:
Filters should be cleaned when C signal appears on Display or (according to usage) each 2-3
weeks. In order to remove C signal, after the filters are cleaned and replaced to their place, press
button more than 3 seconds (when the product is at off position). Letter “E” will appear on
Display and the product will operate as normal. If you would like to continue using the product
without deleting C signal, when you press the button active speed will appear for
1 second, then C signal will appear once more and the motor will continue operating.
NOTE: C signal will appear after usage of the product for 60 hours.
TECHNICAL SPECIFICATIONS
Feeding Voltage 220-240 V 50Hz
Motor Isolation Class
Isolation Class
F
CLASS I
Replacing Lamps
Unplug power cord of your cooker hood.
1W LED LAMBA (Figure 16)
*Open the split extraction plate/glass.
*Take off the aluminium casette filter. (There are on the left and
right back edges covers which you can use for changing the
lamps on the edges. Take this covers off)
*Disconnect cables of LED lights.
*Push onto light to remove them.
*Remove tape between lamp and product body.
*Remove protective tape of new lamp before placing
-7-
Replacing the Lamps
Cut off the connection of the cooker hood with electricity. Take off the aluminum cassette filter.
Take off the failed lamp and replace it with a new one that is of the same rating. (Please wait for the
lamps to cool as they might hurt your hand.)
Replacing 50W Halogen Lamp
In order to change halogen lamps, take the lamp downwards
pushing back of lamp holder downwards and then turning it a
little bit anti-clockwise take it off downwards. Figure 14
Functions of the Product
Your hood is compatible for use with our without chimney.
Usage with chimney
The product should be connected to a chimney that will direct the air out during usage with
chimney. In order to achieve best performance, pay attention that the duct system follows the
shortest way for connection to the chimney. Your product is produced as it will be appropriate for
usage with chimney.
Attention!!!
Outlet of the product should not be connected to air canals that have other smoke as well.
Active Carbon Filter
To provide air recirculation where product's chimney air outlet cannot be connected to exterior,
it is necessary to use active carbon filter with your product. You may purchase this accessory
from authorized sellers and after sales services
Figure 14
Replacing bulb
In order to change the bulb, turn it anti-clockwise and take it off.
Replace it with a new one in the same value by turning it in
clockwise. Figure 16
Figure 16
-10-
Illumination
The product has 2 lamps and one lamp button to operate illumination. Press lamp button in
order to start illumination.
Usage of 5 Speed Digital Control
Usage
Remove protective folio on the inox product after installation.
Speed Selection The product has 5 speeds of ventilation level. One of 1,2,3,4,5 speeds is
selected in accordance with steam of cooking or fry. Motor is started pressing control button
on the front panel. Speed is increased pressing button, and decreased by pressing button.
Automatic timer (TIMER) is available at the models with electronic remote control. When you press
button more than 2 seconds, timer function will be on for 15 minutes. When the timer is on,
Display will signal and the motor will be off automatically 15 minutes later. Please use the cooker
and the product at the same time to enable circulation. Doing so, air suction power will be affected
positively. We recommend you to operate your product for few minutes more after the cooking is
completed to enable absorption rest of smell and steam.
Cleaning Periods of the Aluminum Filters:
Filters should be cleaned when C signal appears on Display or (according to usage) each 2-3
weeks. In order to remove C signal, after the filters are cleaned and replaced to their place, press
button more than 3 seconds (when the product is at off position). Letter “E” will appear on
Display and the product will operate as normal. If you would like to continue using the product
without deleting C signal, when you press the button active speed will appear for
1 second, then C signal will appear once more and the motor will continue operating.
NOTE: C signal will appear after usage of the product for 60 hours.
TECHNICAL SPECIFICATIONS
Feeding Voltage 220-240 V 50Hz
Motor Isolation Class
Isolation Class
F
CLASS I
Replacing Lamps
Unplug power cord of your cooker hood.
1W LED LAMBA (Figure 16)
*Open the split extraction plate/glass.
*Take off the aluminium casette filter. (There are on the left and
right back edges covers which you can use for changing the
lamps on the edges. Take this covers off)
*Disconnect cables of LED lights.
*Push onto light to remove them.
*Remove tape between lamp and product body.
*Remove protective tape of new lamp before placing
-7-
Replacing the Lamps
Cut off the connection of the cooker hood with electricity. Take off the aluminum cassette filter.
Take off the failed lamp and replace it with a new one that is of the same rating. (Please wait for the
lamps to cool as they might hurt your hand.)
Replacing 50W Halogen Lamp
In order to change halogen lamps, take the lamp downwards
pushing back of lamp holder downwards and then turning it a
little bit anti-clockwise take it off downwards. Figure 14
Functions of the Product
Your hood is compatible for use with our without chimney.
Usage with chimney
The product should be connected to a chimney that will direct the air out during usage with
chimney. In order to achieve best performance, pay attention that the duct system follows the
shortest way for connection to the chimney. Your product is produced as it will be appropriate for
usage with chimney.
Attention!!!
Outlet of the product should not be connected to air canals that have other smoke as well.
Active Carbon Filter
To provide air recirculation where product's chimney air outlet cannot be connected to exterior,
it is necessary to use active carbon filter with your product. You may purchase this accessory
from authorized sellers and after sales services
Figure 14
Replacing bulb
In order to change the bulb, turn it anti-clockwise and take it off.
Replace it with a new one in the same value by turning it in
clockwise. Figure 16
Figure 16
-10-
Illumination
The product has 2 lamps and one lamp button to operate illumination. Press lamp button in
order to start illumination.
Usage of 5 Speed Digital Control
Usage
Remove protective folio on the inox product after installation.
Speed Selection The product has 5 speeds of ventilation level. One of 1,2,3,4,5 speeds is
selected in accordance with steam of cooking or fry. Motor is started pressing control button
on the front panel. Speed is increased pressing button, and decreased by pressing button.
Automatic timer (TIMER) is available at the models with electronic remote control. When you press
button more than 2 seconds, timer function will be on for 15 minutes. When the timer is on,
Display will signal and the motor will be off automatically 15 minutes later. Please use the cooker
and the product at the same time to enable circulation. Doing so, air suction power will be affected
positively. We recommend you to operate your product for few minutes more after the cooking is
completed to enable absorption rest of smell and steam.
Cleaning Periods of the Aluminum Filters:
Filters should be cleaned when C signal appears on Display or (according to usage) each 2-3
weeks. In order to remove C signal, after the filters are cleaned and replaced to their place, press
button more than 3 seconds (when the product is at off position). Letter “E” will appear on
Display and the product will operate as normal. If you would like to continue using the product
without deleting C signal, when you press the button active speed will appear for
1 second, then C signal will appear once more and the motor will continue operating.
NOTE: C signal will appear after usage of the product for 60 hours.
TECHNICAL SPECIFICATIONS
Feeding Voltage 220-240 V 50Hz
Motor Isolation Class
Isolation Class
F
CLASS I
Replacing Lamps
Unplug power cord of your cooker hood.
1W LED LAMBA (Figure 16)
*Open the split extraction plate/glass.
*Take off the aluminium casette filter. (There are on the left and
right back edges covers which you can use for changing the
lamps on the edges. Take this covers off)
*Disconnect cables of LED lights.
*Push onto light to remove them.
*Remove tape between lamp and product body.
*Remove protective tape of new lamp before placing
-7-
Replacing the Lamps
Cut off the connection of the cooker hood with electricity. Take off the aluminum cassette filter.
Take off the failed lamp and replace it with a new one that is of the same rating. (Please wait for the
lamps to cool as they might hurt your hand.)
Replacing 50W Halogen Lamp
In order to change halogen lamps, take the lamp downwards
pushing back of lamp holder downwards and then turning it a
little bit anti-clockwise take it off downwards. Figure 14
Functions of the Product
Your hood is compatible for use with our without chimney.
Usage with chimney
The product should be connected to a chimney that will direct the air out during usage with
chimney. In order to achieve best performance, pay attention that the duct system follows the
shortest way for connection to the chimney. Your product is produced as it will be appropriate for
usage with chimney.
Attention!!!
Outlet of the product should not be connected to air canals that have other smoke as well.
Active Carbon Filter
To provide air recirculation where product's chimney air outlet cannot be connected to exterior,
it is necessary to use active carbon filter with your product. You may purchase this accessory
from authorized sellers and after sales services
Figure 14
Replacing bulb
In order to change the bulb, turn it anti-clockwise and take it off.
Replace it with a new one in the same value by turning it in
clockwise. Figure 16
Figure 16
-10-
Illumination
The product has 2 lamps and one lamp button to operate illumination. Press lamp button in
order to start illumination.
Usage of 5 Speed Digital Control
Usage
Remove protective folio on the inox product after installation.
Speed Selection The product has 5 speeds of ventilation level. One of 1,2,3,4,5 speeds is
selected in accordance with steam of cooking or fry. Motor is started pressing control button
on the front panel. Speed is increased pressing button, and decreased by pressing button.
Automatic timer (TIMER) is available at the models with electronic remote control. When you press
button more than 2 seconds, timer function will be on for 15 minutes. When the timer is on,
Display will signal and the motor will be off automatically 15 minutes later. Please use the cooker
and the product at the same time to enable circulation. Doing so, air suction power will be affected
positively. We recommend you to operate your product for few minutes more after the cooking is
completed to enable absorption rest of smell and steam.
Cleaning Periods of the Aluminum Filters:
Filters should be cleaned when C signal appears on Display or (according to usage) each 2-3
weeks. In order to remove C signal, after the filters are cleaned and replaced to their place, press
button more than 3 seconds (when the product is at off position). Letter “E” will appear on
Display and the product will operate as normal. If you would like to continue using the product
without deleting C signal, when you press the button active speed will appear for
1 second, then C signal will appear once more and the motor will continue operating.
NOTE: C signal will appear after usage of the product for 60 hours.
TECHNICAL SPECIFICATIONS
Feeding Voltage 220-240 V 50Hz
Motor Isolation Class
Isolation Class
F
CLASS I
Replacing Lamps
Unplug power cord of your cooker hood.
1W LED LAMBA (Figure 16)
*Open the split extraction plate/glass.
*Take off the aluminium casette filter. (There are on the left and
right back edges covers which you can use for changing the
lamps on the edges. Take this covers off)
*Disconnect cables of LED lights.
*Push onto light to remove them.
*Remove tape between lamp and product body.
*Remove protective tape of new lamp before placing
(IK40 & IK41)
(IK73, IK74, IK77 & IK78)

-8-
Carbon Filter Usage
The product you use has 2 different carbon filter usage feature.Usage of both carbon
filters is as stated below. Cut off power of the product before you change the carbon
filter.Carbon filter should be replaced with a new one each 3-5 months because it is
used at kitchens that does not have chimney outlet.Carbon filter should never be
washed.Oil filters should be montaged on the product even though carbon filter is
used or not. Do not use your product without oil filter.
Changing Carbon Filter
2 Carbon filters should be used at the product.In order to place the carbon filter,
locating the canals on the motor cover and the canals on the carbon filter on the same
level turn it clockwise.In order to take it off, turn it anti-clockwise. Figure 6
-9-
Usage of 3 Speed Digital Control
Peel protective papers out from the inox devices after assembly.
Speed Choice
The device has 3 degrees of ventilation. According to the cooking and frying steam, you can
choose low-middle-high ventilation levels. Buttons on the front panel are used for turning the
device on. The models with eletronic controllers have automatic timers. 15 minutes automatic
timer is turned on, when pressed any of the buttons, which starts the motor up, more than 2
seconds. When timer starts, display will signal and after 15 minutes motor will automaticly stop.
Please turn on hob and hood at the same time to activate circulation. This will provide positive
effect on vacuum power. Let the device run for a while after cooking process is finalised, thus the
remaining smell and steam will be absorbed.
2nd Speed 3rd Speed Lamp Button
Cleaning Periods of Aluminum Filter
Filter should be cleaned when “C” signal appears on the Display or each 2-3 weeks (in accordance
with the usage frequency). After cleaning and replacing filters to their places, button should be
pressed for more than 3 seconds (when the product is off) in order to remove the “C” signal. “E”
signal will appear on Display and product will start working at normal position. If you want to
continue using your product without removing “C” signal, active speed will appear for 1 second
when you press
button, then “C” signal will appear once more and the motor will continue operating.
Illumination
The product has 2 lamps and one lamp button to operate illumination. Press lamp button in
order to start illumination.
Usage of the Control Panel
Speed Selection
You device has 3 levels of ventilation . Depending on the cooking and frying steam , you should
run the device with low- medium or high speed. To run the device , on the front panel there are
motor switch and lamp switch. Please select the desired ventilation speed.
Slider Positions
Illumination
There are two lamps and one switch that controls the illumination on the device. To turn the lamps
on please pres on to the indicated position.
00
(only on rangehoods with motors)
The product you use has carbon lters. Useage of both carbon lters is as stated
below. Cut o󰀨 power of the product before you change the carbon lter. Carbon lter
should be replaced with a new one each 3-5 months because it is used at kitchens
that do not have chimney outlets. Carbon lter should never be washed. Oil lters
should be montaged on the product even if carbon lter is used or not. Do not use
your product with oil lter.

-8-
Carbon Filter Usage
The product you use has 2 different carbon filter usage feature.Usage of both carbon
filters is as stated below. Cut off power of the product before you change the carbon
filter.Carbon filter should be replaced with a new one each 3-5 months because it is
used at kitchens that does not have chimney outlet.Carbon filter should never be
washed.Oil filters should be montaged on the product even though carbon filter is
used or not. Do not use your product without oil filter.
Changing Carbon Filter
2 Carbon filters should be used at the product.In order to place the carbon filter,
locating the canals on the motor cover and the canals on the carbon filter on the same
level turn it clockwise.In order to take it off, turn it anti-clockwise. Figure 6
-9-
Usage of 3 Speed Digital Control
Peel protective papers out from the inox devices after assembly.
Speed Choice
The device has 3 degrees of ventilation. According to the cooking and frying steam, you can
choose low-middle-high ventilation levels. Buttons on the front panel are used for turning the
device on. The models with eletronic controllers have automatic timers. 15 minutes automatic
timer is turned on, when pressed any of the buttons, which starts the motor up, more than 2
seconds. When timer starts, display will signal and after 15 minutes motor will automaticly stop.
Please turn on hob and hood at the same time to activate circulation. This will provide positive
effect on vacuum power. Let the device run for a while after cooking process is finalised, thus the
remaining smell and steam will be absorbed.
2nd Speed 3rd Speed Lamp Button
Cleaning Periods of Aluminum Filter
Filter should be cleaned when “C” signal appears on the Display or each 2-3 weeks (in accordance
with the usage frequency). After cleaning and replacing filters to their places, button should be
pressed for more than 3 seconds (when the product is off) in order to remove the “C” signal. “E”
signal will appear on Display and product will start working at normal position. If you want to
continue using your product without removing “C” signal, active speed will appear for 1 second
when you press
button, then “C” signal will appear once more and the motor will continue operating.
Illumination
The product has 2 lamps and one lamp button to operate illumination. Press lamp button in
order to start illumination.
Usage of the Control Panel
Speed Selection
You device has 3 levels of ventilation . Depending on the cooking and frying steam , you should
run the device with low- medium or high speed. To run the device , on the front panel there are
motor switch and lamp switch. Please select the desired ventilation speed.
Slider Positions
Illumination
There are two lamps and one switch that controls the illumination on the device. To turn the lamps
on please pres on to the indicated position.
00
-8-
Carbon Filter Usage
The product you use has 2 different carbon filter usage feature.Usage of both carbon
filters is as stated below. Cut off power of the product before you change the carbon
filter.Carbon filter should be replaced with a new one each 3-5 months because it is
used at kitchens that does not have chimney outlet.Carbon filter should never be
washed.Oil filters should be montaged on the product even though carbon filter is
used or not. Do not use your product without oil filter.
Changing Carbon Filter
2 Carbon filters should be used at the product.In order to place the carbon filter,
locating the canals on the motor cover and the canals on the carbon filter on the same
level turn it clockwise.In order to take it off, turn it anti-clockwise. Figure 6
-9-
Usage of 3 Speed Digital Control
Peel protective papers out from the inox devices after assembly.
Speed Choice
The device has 3 degrees of ventilation. According to the cooking and frying steam, you can
choose low-middle-high ventilation levels. Buttons on the front panel are used for turning the
device on. The models with eletronic controllers have automatic timers. 15 minutes automatic
timer is turned on, when pressed any of the buttons, which starts the motor up, more than 2
seconds. When timer starts, display will signal and after 15 minutes motor will automaticly stop.
Please turn on hob and hood at the same time to activate circulation. This will provide positive
effect on vacuum power. Let the device run for a while after cooking process is finalised, thus the
remaining smell and steam will be absorbed.
2nd Speed 3rd Speed Lamp Button
Cleaning Periods of Aluminum Filter
Filter should be cleaned when “C” signal appears on the Display or each 2-3 weeks (in accordance
with the usage frequency). After cleaning and replacing filters to their places, button should be
pressed for more than 3 seconds (when the product is off) in order to remove the “C” signal. “E”
signal will appear on Display and product will start working at normal position. If you want to
continue using your product without removing “C” signal, active speed will appear for 1 second
when you press
button, then “C” signal will appear once more and the motor will continue operating.
Illumination
The product has 2 lamps and one lamp button to operate illumination. Press lamp button in
order to start illumination.
Usage of the Control Panel
Speed Selection
You device has 3 levels of ventilation . Depending on the cooking and frying steam , you should
run the device with low- medium or high speed. To run the device , on the front panel there are
motor switch and lamp switch. Please select the desired ventilation speed.
Slider Positions
Illumination
There are two lamps and one switch that controls the illumination on the device. To turn the lamps
on please pres on to the indicated position.
00
(IK40 & IK41)
-7-
Replacing the Lamps
Cut off the connection of the cooker hood with electricity. Take off the aluminum cassette filter.
Take off the failed lamp and replace it with a new one that is of the same rating. (Please wait for the
lamps to cool as they might hurt your hand.)
Replacing 50W Halogen Lamp
In order to change halogen lamps, take the lamp downwards
pushing back of lamp holder downwards and then turning it a
little bit anti-clockwise take it off downwards. Figure 14
Functions of the Product
Your hood is compatible for use with our without chimney.
Usage with chimney
The product should be connected to a chimney that will direct the air out during usage with
chimney. In order to achieve best performance, pay attention that the duct system follows the
shortest way for connection to the chimney. Your product is produced as it will be appropriate for
usage with chimney.
Attention!!!
Outlet of the product should not be connected to air canals that have other smoke as well.
Active Carbon Filter
To provide air recirculation where product's chimney air outlet cannot be connected to exterior,
it is necessary to use active carbon filter with your product. You may purchase this accessory
from authorized sellers and after sales services
Figure 14
Replacing bulb
In order to change the bulb, turn it anti-clockwise and take it off.
Replace it with a new one in the same value by turning it in
clockwise. Figure 16
Figure 16
-10-
Illumination
The product has 2 lamps and one lamp button to operate illumination. Press lamp button in
order to start illumination.
Usage of 5 Speed Digital Control
Usage
Remove protective folio on the inox product after installation.
Speed Selection The product has 5 speeds of ventilation level. One of 1,2,3,4,5 speeds is
selected in accordance with steam of cooking or fry. Motor is started pressing control button
on the front panel. Speed is increased pressing button, and decreased by pressing button.
Automatic timer (TIMER) is available at the models with electronic remote control. When you
press
button more than 2 seconds, timer function will be on for 15 minutes. When the timer is on,
Display will signal and the motor will be off automatically 15 minutes later. Please use the cooker
and the product at the same time to enable circulation. Doing so, air suction power will be affected
positively. We recommend you to operate your product for few minutes more after the cooking is
completed to enable absorption rest of smell and steam.
Cleaning Periods of the Aluminum Filters:
Filters should be cleaned when C signal appears on Display or (according to usage) each 2-3
weeks. In order to remove C signal, after the filters are cleaned and replaced to their place, press
button more than 3 seconds (when the product is at off position). Letter “E” will appear on
Display and the product will operate as normal. If you would like to continue using the product
without deleting C signal, when you press the button active speed will appear for
1 second, then C signal will appear once more and the motor will continue operating.
NOTE: C signal will appear after usage of the product for 60 hours.
TECHNICAL SPECIFICATIONS
Feeding Voltage 220-240 V 50Hz
Motor Isolation Class
Isolation Class
F
CLASS I
Replacing Lamps
Unplug power cord of your cooker hood.
1W LED LAMBA (Figure 16)
*Open the split extraction plate/glass.
*Take off the aluminium casette filter. (There are on the left and
right back edges covers which you can use for changing the
lamps on the edges. Take this covers off)
*Disconnect cables of LED lights.
*Push onto light to remove them.
*Remove tape between lamp and product body.
*Remove protective tape of new lamp before placing
-7-
Replacing the Lamps
Cut off the connection of the cooker hood with electricity. Take off the aluminum cassette filter.
Take off the failed lamp and replace it with a new one that is of the same rating. (Please wait for the
lamps to cool as they might hurt your hand.)
Replacing 50W Halogen Lamp
In order to change halogen lamps, take the lamp downwards
pushing back of lamp holder downwards and then turning it a
little bit anti-clockwise take it off downwards. Figure 14
Functions of the Product
Your hood is compatible for use with our without chimney.
Usage with chimney
The product should be connected to a chimney that will direct the air out during usage with
chimney. In order to achieve best performance, pay attention that the duct system follows the
shortest way for connection to the chimney. Your product is produced as it will be appropriate for
usage with chimney.
Attention!!!
Outlet of the product should not be connected to air canals that have other smoke as well.
Active Carbon Filter
To provide air recirculation where product's chimney air outlet cannot be connected to exterior,
it is necessary to use active carbon filter with your product. You may purchase this accessory
from authorized sellers and after sales services
Figure 14
Replacing bulb
In order to change the bulb, turn it anti-clockwise and take it off.
Replace it with a new one in the same value by turning it in
clockwise. Figure 16
Figure 16
-10-
Illumination
The product has 2 lamps and one lamp button to operate illumination. Press lamp button in
order to start illumination.
Usage of 5 Speed Digital Control
Usage
Remove protective folio on the inox product after installation.
Speed Selection The product has 5 speeds of ventilation level. One of 1,2,3,4,5 speeds is
selected in accordance with steam of cooking or fry. Motor is started pressing control button
on the front panel. Speed is increased pressing button, and decreased by pressing button.
Automatic timer (TIMER) is available at the models with electronic remote control. When you press
button more than 2 seconds, timer function will be on for 15 minutes. When the timer is on,
Display will signal and the motor will be off automatically 15 minutes later. Please use the cooker
and the product at the same time to enable circulation. Doing so, air suction power will be affected
positively. We recommend you to operate your product for few minutes more after the cooking is
completed to enable absorption rest of smell and steam.
Cleaning Periods of the Aluminum Filters:
Filters should be cleaned when C signal appears on Display or (according to usage) each 2-3
weeks. In order to remove C signal, after the filters are cleaned and replaced to their place, press
button more than 3 seconds (when the product is at off position). Letter “E” will appear on
Display and the product will operate as normal. If you would like to continue using the product
without deleting C signal, when you press the button active speed will appear for
1 second, then C signal will appear once more and the motor will continue operating.
NOTE: C signal will appear after usage of the product for 60 hours.
TECHNICAL SPECIFICATIONS
Feeding Voltage 220-240 V 50Hz
Motor Isolation Class
Isolation Class
F
CLASS I
Replacing Lamps
Unplug power cord of your cooker hood.
1W LED LAMBA (Figure 16)
*Open the split extraction plate/glass.
*Take off the aluminium casette filter. (There are on the left and
right back edges covers which you can use for changing the
lamps on the edges. Take this covers off)
*Disconnect cables of LED lights.
*Push onto light to remove them.
*Remove tape between lamp and product body.
*Remove protective tape of new lamp before placing
-7-
Replacing the Lamps
Cut off the connection of the cooker hood with electricity. Take off the aluminum cassette filter.
Take off the failed lamp and replace it with a new one that is of the same rating. (Please wait for the
lamps to cool as they might hurt your hand.)
Replacing 50W Halogen Lamp
In order to change halogen lamps, take the lamp downwards
pushing back of lamp holder downwards and then turning it a
little bit anti-clockwise take it off downwards. Figure 14
Functions of the Product
Your hood is compatible for use with our without chimney.
Usage with chimney
The product should be connected to a chimney that will direct the air out during usage with
chimney. In order to achieve best performance, pay attention that the duct system follows the
shortest way for connection to the chimney. Your product is produced as it will be appropriate for
usage with chimney.
Attention!!!
Outlet of the product should not be connected to air canals that have other smoke as well.
Active Carbon Filter
To provide air recirculation where product's chimney air outlet cannot be connected to exterior,
it is necessary to use active carbon filter with your product. You may purchase this accessory
from authorized sellers and after sales services
Figure 14
Replacing bulb
In order to change the bulb, turn it anti-clockwise and take it off.
Replace it with a new one in the same value by turning it in
clockwise. Figure 16
Figure 16
-10-
Illumination
The product has 2 lamps and one lamp button to operate illumination. Press lamp button in
order to start illumination.
Usage of 5 Speed Digital Control
Usage
Remove protective folio on the inox product after installation.
Speed Selection The product has 5 speeds of ventilation level. One of 1,2,3,4,5 speeds is
selected in accordance with steam of cooking or fry. Motor is started pressing control button
on the front panel. Speed is increased pressing button, and decreased by pressing button.
Automatic timer (TIMER) is available at the models with electronic remote control. When you press
button more than 2 seconds, timer function will be on for 15 minutes. When the timer is on,
Display will signal and the motor will be off automatically 15 minutes later. Please use the cooker
and the product at the same time to enable circulation. Doing so, air suction power will be affected
positively. We recommend you to operate your product for few minutes more after the cooking is
completed to enable absorption rest of smell and steam.
Cleaning Periods of the Aluminum Filters:
Filters should be cleaned when C signal appears on Display or (according to usage) each 2-3
weeks. In order to remove C signal, after the filters are cleaned and replaced to their place, press
button more than 3 seconds (when the product is at off position). Letter “E” will appear on
Display and the product will operate as normal. If you would like to continue using the product
without deleting C signal, when you press the button active speed will appear for
1 second, then C signal will appear once more and the motor will continue operating.
NOTE: C signal will appear after usage of the product for 60 hours.
TECHNICAL SPECIFICATIONS
Feeding Voltage 220-240 V 50Hz
Motor Isolation Class
Isolation Class
F
CLASS I
Replacing Lamps
Unplug power cord of your cooker hood.
1W LED LAMBA (Figure 16)
*Open the split extraction plate/glass.
*Take off the aluminium casette filter. (There are on the left and
right back edges covers which you can use for changing the
lamps on the edges. Take this covers off)
*Disconnect cables of LED lights.
*Push onto light to remove them.
*Remove tape between lamp and product body.
*Remove protective tape of new lamp before placing
IK73, IK74, IK77, IK78

-7-
Replacing the Lamps
Cut off the connection of the cooker hood with electricity. Take off the aluminum cassette filter.
Take off the failed lamp and replace it with a new one that is of the same rating. (Please wait for the
lamps to cool as they might hurt your hand.)
Replacing 50W Halogen Lamp
In order to change halogen lamps, take the lamp downwards
pushing back of lamp holder downwards and then turning it a
little bit anti-clockwise take it off downwards. Figure 14
Functions of the Product
Your hood is compatible for use with our without chimney.
Usage with chimney
The product should be connected to a chimney that will direct the air out during usage with
chimney. In order to achieve best performance, pay attention that the duct system follows the
shortest way for connection to the chimney. Your product is produced as it will be appropriate for
usage with chimney.
Attention!!!
Outlet of the product should not be connected to air canals that have other smoke as well.
Active Carbon Filter
To provide air recirculation where product's chimney air outlet cannot be connected to exterior,
it is necessary to use active carbon filter with your product. You may purchase this accessory
from authorized sellers and after sales services
Figure 14
Replacing bulb
In order to change the bulb, turn it anti-clockwise and take it off.
Replace it with a new one in the same value by turning it in
clockwise. Figure 16
Figure 16
-10-
Illumination
The product has 2 lamps and one lamp button to operate illumination. Press lamp button in
order to start illumination.
Usage of 5 Speed Digital Control
Usage
Remove protective folio on the inox product after installation.
Speed Selection The product has 5 speeds of ventilation level. One of 1,2,3,4,5 speeds is
selected in accordance with steam of cooking or fry. Motor is started pressing control button
on the front panel. Speed is increased pressing button, and decreased by pressing button.
Automatic timer (TIMER) is available at the models with electronic remote control. When you press
button more than 2 seconds, timer function will be on for 15 minutes. When the timer is on,
Display will signal and the motor will be off automatically 15 minutes later. Please use the cooker
and the product at the same time to enable circulation. Doing so, air suction power will be affected
positively. We recommend you to operate your product for few minutes more after the cooking is
completed to enable absorption rest of smell and steam.
Cleaning Periods of the Aluminum Filters:
Filters should be cleaned when C signal appears on Display or (according to usage) each 2-3
weeks. In order to remove C signal, after the filters are cleaned and replaced to their place,
press
button more than 3 seconds (when the product is at off position). Letter “E” will appear on
Display and the product will operate as normal. If you would like to continue using the product
without deleting C signal, when you press the button active speed will appear for
1 second, then C signal will appear once more and the motor will continue operating.
NOTE: C signal will appear after usage of the product for 60 hours.
TECHNICAL SPECIFICATIONS
Feeding Voltage 220-240 V 50Hz
Motor Isolation Class
Isolation Class
F
CLASS I
Replacing Lamps
Unplug power cord of your cooker hood.
1W LED LAMBA (Figure 16)
*Open the split extraction plate/glass.
*Take off the aluminium casette filter. (There are on the left and
right back edges covers which you can use for changing the
lamps on the edges. Take this covers off)
*Disconnect cables of LED lights.
*Push onto light to remove them.
*Remove tape between lamp and product body.
*Remove protective tape of new lamp before placing
-7-
Replacing the Lamps
Cut off the connection of the cooker hood with electricity. Take off the aluminum cassette filter.
Take off the failed lamp and replace it with a new one that is of the same rating. (Please wait for the
lamps to cool as they might hurt your hand.)
Replacing 50W Halogen Lamp
In order to change halogen lamps, take the lamp downwards
pushing back of lamp holder downwards and then turning it a
little bit anti-clockwise take it off downwards. Figure 14
Functions of the Product
Your hood is compatible for use with our without chimney.
Usage with chimney
The product should be connected to a chimney that will direct the air out during usage with
chimney. In order to achieve best performance, pay attention that the duct system follows the
shortest way for connection to the chimney. Your product is produced as it will be appropriate for
usage with chimney.
Attention!!!
Outlet of the product should not be connected to air canals that have other smoke as well.
Active Carbon Filter
To provide air recirculation where product's chimney air outlet cannot be connected to exterior,
it is necessary to use active carbon filter with your product. You may purchase this accessory
from authorized sellers and after sales services
Figure 14
Replacing bulb
In order to change the bulb, turn it anti-clockwise and take it off.
Replace it with a new one in the same value by turning it in
clockwise. Figure 16
Figure 16
-10-
Illumination
The product has 2 lamps and one lamp button to operate illumination. Press lamp button in
order to start illumination.
Usage of 5 Speed Digital Control
Usage
Remove protective folio on the inox product after installation.
Speed Selection The product has 5 speeds of ventilation level. One of 1,2,3,4,5 speeds is
selected in accordance with steam of cooking or fry. Motor is started pressing control button
on the front panel. Speed is increased pressing button, and decreased by pressing button.
Automatic timer (TIMER) is available at the models with electronic remote control. When you press
button more than 2 seconds, timer function will be on for 15 minutes. When the timer is on,
Display will signal and the motor will be off automatically 15 minutes later. Please use the cooker
and the product at the same time to enable circulation. Doing so, air suction power will be affected
positively. We recommend you to operate your product for few minutes more after the cooking is
completed to enable absorption rest of smell and steam.
Cleaning Periods of the Aluminum Filters:
Filters should be cleaned when C signal appears on Display or (according to usage) each 2-3
weeks. In order to remove C signal, after the filters are cleaned and replaced to their place, press
button more than 3 seconds (when the product is at off position). Letter “E” will appear on
Display and the product will operate as normal. If you would like to continue using the product
without deleting C signal, when you press the button active speed will appear for
1 second, then C signal will appear once more and the motor will continue operating.
NOTE: C signal will appear after usage of the product for 60 hours.
TECHNICAL SPECIFICATIONS
Feeding Voltage 220-240 V 50Hz
Motor Isolation Class
Isolation Class
F
CLASS I
Replacing Lamps
Unplug power cord of your cooker hood.
1W LED LAMBA (Figure 16)
*Open the split extraction plate/glass.
*Take off the aluminium casette filter. (There are on the left and
right back edges covers which you can use for changing the
lamps on the edges. Take this covers off)
*Disconnect cables of LED lights.
*Push onto light to remove them.
*Remove tape between lamp and product body.
*Remove protective tape of new lamp before placing
Placement of remote motor (IK73 & IK74)
Remote motor power pack must be tted with an Ikon remote motor, failure to do this will void
the warranty.
IK15 remote motor is recommended where the distance of extraction is less than 5 meters
(deduct a meter per bend)
Remote motor can be mounted up to 6 meters from the hood. It is recommended that the
motor is either insulated or mounted to reduce vibration.
-8-
Carbon Filter Usage
The product you use has 2 different carbon filter usage feature.Usage of both carbon
filters is as stated below. Cut off power of the product before you change the carbon
filter.Carbon filter should be replaced with a new one each 3-5 months because it is
used at kitchens that does not have chimney outlet.Carbon filter should never be
washed.Oil filters should be montaged on the product even though carbon filter is
used or not. Do not use your product without oil filter.
Changing Carbon Filter
2 Carbon filters should be used at the product.In order to place the carbon filter,
locating the canals on the motor cover and the canals on the carbon filter on the same
level turn it clockwise.In order to take it off, turn it anti-clockwise. Figure 6
-9-
Usage of 3 Speed Digital Control
Peel protective papers out from the inox devices after assembly.
Speed Choice
The device has 3 degrees of ventilation. According to the cooking and frying steam, you can
choose low-middle-high ventilation levels. Buttons on the front panel are used for turning the
device on. The models with eletronic controllers have automatic timers. 15 minutes automatic
timer is turned on, when pressed any of the buttons, which starts the motor up, more than 2
seconds. When timer starts, display will signal and after 15 minutes motor will automaticly stop.
Please turn on hob and hood at the same time to activate circulation. This will provide positive
effect on vacuum power. Let the device run for a while after cooking process is finalised, thus the
remaining smell and steam will be absorbed.
2nd Speed 3rd Speed Lamp Button
Cleaning Periods of Aluminum Filter
Filter should be cleaned when “C” signal appears on the Display or each 2-3 weeks (in accordance
with the usage frequency). After cleaning and replacing filters to their places, button should be
pressed for more than 3 seconds (when the product is off) in order to remove the “C” signal. “E”
signal will appear on Display and product will start working at normal position. If you want to
continue using your product without removing “C” signal, active speed will appear for 1 second
when you press
button, then “C” signal will appear once more and the motor will continue operating.
Illumination
The product has 2 lamps and one lamp button to operate illumination. Press lamp button in
order to start illumination.
Usage of the Control Panel
Speed Selection
You device has 3 levels of ventilation . Depending on the cooking and frying steam , you should
run the device with low- medium or high speed. To run the device , on the front panel there are
motor switch and lamp switch. Please select the desired ventilation speed.
Slider Positions
Illumination
There are two lamps and one switch that controls the illumination on the device. To turn the lamps
on please pres on to the indicated position.
00
(IK40 & IK41)
IK73, IK74, IK77, IK78

-6-
Ø 3 mm
WARNING : During drilling the hanging holes , please pay attention to the diameter of the
holes to be used for hanging the hood.
If the diameters of hanging holes are not as pointed , the hood can not be assembled properly.
Installation of the aluminum duct
Connect one end of the aluminum vent to the previously
mounted plastic vent.
Connect the other end of the aluminum vent to kitchen
chimney. Make sure that said two connection are not
disconnected under maximum hood speed (Figure 4).
Figure 4
Drilling suspension holes
For Model 1170 - 1171- -1173 / 60
By using a Ø3mm driller, drill points marked as A, B, C, D
in mounting scheme.
For Model 1170 - 1171 - 1173 / 90
By using a Ø3mm driller, drill points marked as A, B, C, D,
E, F in mounting scheme.
For Model 1172 - 60
By using a Ø3mm driller, drill points marked as A, B, C,
D,E,F in mounting scheme.
For Model 1172 - 90
By using a Ø3mm driller, drill points marked as A, B, C,
D,E,F,G,H in mounting scheme.
Mounting into cabinet
Place the hood into the cabinet (Picture 5).
Align holes drilled according to mounting scheme and
holes on the product panel, and fix the product.
(Figure 6).
Mounting
holes
MAINTENANCE
*Disconnect electricity connection before maintenance and
cleaning process.
*Aluminum cassette filter holds the dust and the oil in the air.
*Metal filter should be washed once in a month with hot and
soaped water or, if possible, at dishwasher (60C).
*Take off aluminum cassette filter pressing on springy
latches on end point. After cleaning, do not replace before it
dries.
*Outer surface of the cooker hood should be wiped with a
wet cloth that is wetted with water or alcohol.
*Please avoid contact of electronic parts with water or
similar materials.
*Using Inox cleaning and maintenance products available in
the market will help your product to perform longer.
Warning: Aluminum filters may be washed in the
dishwasher. Color of aluminum filters may change after
several washings. This is normal and it is not necessary to
change the filters.
Efficient Ventilation
In order to ensure correct ventilation, keep your kitchen windows closed.
IMPORTANT NOTE
Please pay attention when the product is operated at the same time with a product which operates
using air and fuel (for instance; heater, water heater etc. which operates using gas, diesel fuel,
coal or wood), since cooker hood may affect burning negatively as it directs the air out.
This warning is not valid for usage without chimney.
Washable Aluminum
Cassette Filter
-11-

-12-
Standard Accessories
Plastic Outlet (Figure 1)
Plastic outlet mounted to air outlet of the cooker hood
Min.65 cm
Min.75 cm
Place of the Product:
After installation of your product, distance between
range hood and electrical hob should be at least 65
cm and gas hobs at least 75cm. Figure 2
Installation, taking off your product from its package:
*Check if there is any deformation on your product.
*Transportation damages and failures should immediately be reported to the transportation
responsible.
*If you notice any damage please report to the seller.
*Do not allow children to play with packing material!!!
Figure 1
Figure 2
Figure 3
Screwing the plastic vent.
Before installing the hood into the cabinet, screw the
plastic vent.
3,5 x 9,5 RYSB
Screws
COOKER HOOD MOUNTING
If the product does not work:
Before you contact the technical service:
Make sure that the product is plugged in and the electric fuse of the electric wiring is running. Do
not take any action that will damage the product. Before you contact with technical service, check
your cooker hood according to Table 1. If the problem goes on, contact the seller or the most
authorized service.
Check electric connection(Voltage of the
electric network should be between 220-240V,
cooker hood should be connected to grounded
Check motor switch (Motor switch should be at
on position) Check motor switch (Motor switch should be at
on position) Check aluminum filter(Aluminum Cassette Filter should be washed once a month at normal conditions.)
Check lamps(Lamps should be firm.)
Check outlet (Outlet should be open) Check Carbon Filter (Carbon filter should be replaced with a new one each 2-3 months at the
models with Carbon Filter at normal
conditions)
Cooker-hood does not work
Illumination Lamp does not work
Cooker-hoods air suction is weak
Cooker-hood does not direct air out
(at places without chimney)
In order to use the cooker hood efficiently;
*Use ducts of 150/120mm diameter and as few bends as possible when you make the chimney
connection.
*Pay attention to aluminum filters' cleaning periods and changing periods of carbon filters.
*Use the product at middle speed if high suction power is not necessary.
* In order to ensure that ventilation occurs correctly, windows of the kitchen should be kept
-5-

-4-
*Keep package materials away from
children as they may be dangerous for
them.
*Be sure that your child does not play with
the product. Do not allow kids to use your
product.
*If power supply cable is damaged, this
cable should be changed by its producer or
its service agency or a personnel who is a
specialist at the same level in order to
prevent a dangerous situation.
Warning about Transportation and Carriage
*All the materials used at package of your product are suitable for recycling.
*Please comply with the signs on the product's box during transportation.
*Hold the holders placed at sides of the box in order to carry your product.
If you need transportation;
*Keep the original box.
*Carry your product in its original box; comply with the carrying signs on the product's box.
If there is no original package;
*Do not put heavy material on the chimney hood.
*Keep the external surface from bash.
*Pack your product to avoid damages.
Installation, taking off your product from its package:
*Check if there is any deformation on your product.
*Transportation damages and failures should immediately be reported to the transportation
responsible.
*If you notice any damage please report to the seller.
*Do not allow children to play with packing material!!!
*In case of flame, cut power of the cooker
hood and the cooking appliances, cover the
flame. Never use water in order to
extinguish it.
Use “MAX 6 A” fuse at cooker hood
installment for your security.
“CAUTION: Accessible parts may become hot when used with cooking appliances”
''The appliance is not to be used by children or persons with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have
been given supervision or instruction''
-13-
FUSE
ELECTRONIC CIRCUIT
CAPASITOR
5 µf/400 V
M
FUSE
800m³/h 5 Speed
FUSE
10 10
10
M
CAP
CAP
N M1 M2 M3 M4
M5
LAMP
500 m³/h 3 Speed
FUSE
CONTROL PANEL
ELECTRONIC CIRCUIT
M
INPUT : 220 - 240 V AC / 50 Hz
WHITE
WHITE
LAMP
BLACK
BLUE RED
WHITE
BROWN
YELLOW/GREEN
BLUE
800 m³/h 3 Speed
CONTROL PANEL
LAMP
WHITE
WHITE
BLACK
WHITE
BLUE
RED
BROWN
BROWN
YELLOW/GREEN
BLUE
INPUT : 220 - 240 V AC / 50 Hz
LAMP
BLACK
GREY
YELLOW
WHITE
BLUE
BROWN
RED
GREY
GREY
BROWN
YELLOW/GREEN
BLUE
WHITE WHITE
WHITE
WHITE
ELECTRONIC CIRCUIT
BUTTON BOX
5µF
YELLOW-GREEN
(1)
(2)
(3)
YELLOW/GREEN
Eco 3 Speed