Ikon IK82 User manual

TAPWARE RANGEHOODS COOKTOPS WASTE DISPOSALS KITCHEN/LAUNDRY SINKS BATHROOM BASINS
Rangehood Installation and User Manual
Model: IK82

-2-
INTRODUCTION OF DEVICE
3110 3120 3130 3131
3140-3141 3150-3151-3155 3160
3158
3170
250
262
46
426
500
Min 635 Max 1015
598,798,898
500
20
400
20
80
600
40
500
598,798,898
250
262
Min 635 Max 1015
20
400
600
2080
500
598,898
250
262
Min 675 Max 1055
83
20
400
600
2080
500
598,898
250
262
Min 675 Max 1055
83
20
400
600
2080
80
500
598,898
250
262
Min 675 Max 1055
20
400
600
2080
20
57,66
460,600
598,898
410
500
Min (90) 635 (60) 630
Min (90) 1215 (60) 1210
600 400
20
80
250
262
25
80
400
500
20
500
598,898
250
262
420
Min (90) 600 (60) 535
Max (90) 980 (60) 915
412
62,126
46
500
250
Min 640 Max 1020
600,700,800,900
20
400
600
2080
262
426
500
60
500
600,700,800,900
250
262
Min 655 Max 1035
2080
600
400
20
3110 3120 3130 3131
3140-3141 3150-3151-3155 3160
3158
3170
1) Internal Chimney
2) External Chimney
3) Control Panel
4) Cooker Lighting
5) Aluminum Cassette Filter
6) Tempered Glass
1
2
3
4
5
6
1
2
3
4
5
1
2
3
4
5
1
2
3
4
5
1
2
3
4
5
1
2
3
4
5
6
1
2
3
4
5
6
1
2
3
4
5
6
1
2
3
4
5
FUSE
ELECTRONIC CIRCUIT
CAPASITOR
5 µf/400 V
M
FUSE
800m³/h 5 Speed
FUSE 5µF
10 10
10
M
CAP
CAP
N M1 M2 M3 M4
M5
LAMP
500 m³/h 3 Speed
FUSE
CONTROL PANEL
ELECTRONIC CIRCUIT
M
5µF
BROWN
YELLOW/GREEN
BLUE
M
CAP
CAP
N M1 M2 M3 M4
M5
BUTTON BOX
INPUT : 220 - 240 V AC / 50 Hz
ELECTRONIC CIRCUIT
M
WHITE
WHITE
LAMP
BLACK
BLUE RED
WHITE
BROWN
YELLOW/GREEN
BLUE
800 m³/h 3 Speed
CONTROL PANEL
LAMP
WHITE
WHITE
BLACK
WHITE
BLUE
RED
BROWN
BROWN
YELLOW/GREEN
BLUE
INPUT : 220 - 240 V AC / 50 Hz
INPUT : 220 - 240 V AC / 50 Hz
CONTROL PANEL
CAPASITOR
800 m³/h 3 Speed -12V
WHITE
BLACK
BLUE RED
BROWN
TRANSFORMER
220 V 12 V
WHITE
WHITE
LAMP
12 V
BROWN
YELLOW/GREEN
BLUE
LAMP
BLACK
GREY
YELLOW
WHITE
BLUE
BROWN
RED
GREY
GREY
BROWN
YELLOW/GREEN
BLUE
WHITE WHITE
WHITE
WHITE
ELECTRONIC CIRCUIT
BUTTON BOX
INPUT : 220 - 240 V AC / 50 Hz
LAMP
WHITE
WHITE
WHITE
WHITE
BLACK
GREY
YELLOW
WHITE
BLUE
BROWN
RED
GREY
ELECTRONIC CIRCUIT
800m³/h 5 Speed LCD

-3-
*Before you take pot, fry-pan etc. from the
hob, put their lids on.
*Do not leave hot oil on the hob. Pots that
have hot oil in them may cause selfignition.
*Pay attention to curtains and covers during
cooking of meals like frying because oil may
flare up.
*Make sure that filters are changed in
convenience. Filters that are not changed at
appropriate time has risk of causing fire due
to oil that will be gathered on them.
*Do not use filter materials that are not flame
resistant instead of filter.
*Do not operate your product without
aluminum filter; do not remove filters when
the product is on.
*In case of flame, cut power of the product
and the cooking appliances. (Cut power of
the product by plugging it off the socket).
*Your product may cause fire risk if cleaning
is not applied periodically.
*Cut power of the product before
maintenance process. (Cut power of the
device by unplugging it)
*When chimney hood and the appliances
working with energy other than electricity
are operated at the same time, negative
pressure in the room should not be more
than 4 Pa (4 x 10 bar)
*If there is an appliance working with fuel or
gaseous fuel at the same place with your
hood, this appliance's exhaust should be
isolated from its volume totally and the
appliance should be hermetic type.
*When chimney connection is applied to
your product, use ducts of 150mm or
120mm diameter. Duct connection should
be as short as possible and should include
few bends.
*This product is designed for usage at
home.
*Your products usage voltage is 220-240
Volts~50Hz
*Grounded plug is used at your product's
electric network cable. This cable should
definitely be plugged in a grounded socket.
*All electrical networks should be set by a
qualified electrician.
*Installation applied by unauthorized
people may cause the product to operate at
low performance, damage of the product
and accidents.
*Power supply cable should not be exposed
to press or smash during montage. Network
cordon should not be placed near the
cookers; it may cause fire if it melts.
*Do not plug into the socket before
installation of the product is completed.
*Keep the plug at a reachable place so that
you can unplug it in case of any danger.
*Do not touch the lamps when they are on
for long time. Lamps may hurt your hand as
they will be hot.
*Kitchen cooker hoods are designed for
usage during normal and home-style
cooking. If it is used for other purposes,
failure risk occurs and it will be out of
warranty.
*Follow applicable rules and directions for
passing out outlet air. (This warning is not
valid for usage without chimney.)
*Flaming foods should not be cooked under
the product.
*Start your product after you put pot, fry-pan
etc. on the hob . Oth erwise hig h
temperature may cause some parts of your
product to get deformed.
-5
WARNINGS AND SAFETY PRECAUTIONS
-18-
If the product does not work:
Before you contact the technical service:
Make sure that the product is plugged in and the electric fuse of the electric wiring is running. Do
not take any action that will damage the product. Before you contact with technical service, check
your cooker hood according to Table 1. If the problem goes on, contact the seller or the most
authorized service.
Check electric connection(Voltage of the
electric network should be between 220-240V,
cooker hood should be connected to grounded
Check motor switch (Motor switch should be at
on position)
Check motor switch (Motor switch should be at
on position)
Check aluminum filter(Aluminum Cassette
Filter should be washed once a month at
normal conditions.)
Check lamps(Lamps should be firm.)
Check outlet (Outlet should be open) Check Carbon Filter (Carbon filter should be
replaced with a new one each 2-3 months at the
models with Carbo n F i l t e r at normal
conditions)
Cooker-hood does not work
Illumination Lamp does not work
Cooker-hoods air suction is weak
Cooker-hood does not direct air out
(at places without chimney)
In order to use the cooker hood efficiently;
*Use ducts of 150/120mm diameter and as few bends as possible when you make the chimney
connection.
*Pay attention to aluminum filters' cleaning periods and changing periods of carbon filters.
*Use the product at middle speed if high suction power is not necessary.
* In order to ensure that ventilation occurs correctly, windows of the kitchen should be kept

-4-
*Keep package materials away from
children as they may be dangerous for
them.
*Be sure that your child does not play with
the product. Do not allow kids to use your
product.
*If power supply cable is damaged, this
cable should be changed by its producer or
its service agency or a personnel who is a
specialist at the same level in order to
prevent a dangerous situation.
Warning about Transportation and Carriage
*All the materials used at package of your product are suitable for recycling.
*Please comply with the signs on the product's box during transportation.
*Hold the holders placed at sides of the box in order to carry your product.
If you need transportation;
*Keep the original box.
*Carry your product in its original box; comply with the carrying signs on the product's box.
If there is no original package;
*Do not put heavy material on the chimney hood.
*Keep the external surface from bash.
*Pack your product to avoid damages.
Installation, taking off your product from its package:
*Check if there is any deformation on your product.
*Transportation damages and failures should immediately be reported to the transportation
responsible.
*If you notice any damage please report to the seller.
*Do not allow children to play with packing material!!!
*In case of flame, cut power of the cooker
hood and the cooking appliances, cover the
flame. Never use water in order to
extinguish it.
Use “MAX 6 A” fuse at cooker hood
installment for your security.
“CAUTION: Accessible parts may become hot when used with cooking appliances”
''The appliance is not to be used by children or persons with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have
been given supervision or instruction''
-17-
MAINTENANCE
*Disconnect electricity connection before maintenance and
cleaning process.
*Aluminum cassette filter holds the dust and the oil in the air.
*Metal filter should be washed once in a month with hot and
soaped water or, if possible, at dishwasher (60C).
*Take off aluminum cassette filter pressing on springy
latches on end point. After cleaning, do not replace before it
dries.
*Outer surface of the cooker hood should be wiped with a
wet cloth that is wetted with water or alcohol.
*Please avoid contact of electronic parts with water or
similar materials.
*Using Inox cleaning and maintenance products available in
the market will help your product to perform longer.
Warning: Aluminum filters may be washed in the
dishwasher. Color of aluminum filters may change after
several washings. This is normal and it is not necessary to
change the filters.
Efficient Ventilation
In order to ensure correct ventilation, keep your kitchen windows closed.
IMPORTANT NOTE
Please pay attention when the product is operated at the same time with a product which operates
using air and fuel (for instance; heater, water heater etc. which operates using gas, diesel fuel,
coal or wood), since cooker hood may affect burning negatively as it directs the air out.
This warning is not valid for usage without chimney.
Washable Aluminum
Cassette Filter

-5-
Standard Accessories
Plastic Outlet (Figure 1)
Plastic outlet mounted to air outlet of the cooker hood
Min.65 cm
Min.75 cm
Place of the Product:
After installation of your product, distance between
range hood and electrical hob should be at least 65
cm and gas hobs at least 75cm. Figure 2
Installation, taking off your product from its package:
*Check if there is any deformation on your product.
*Transportation damages and failures should immediately be reported to the transportation
responsible.
*If you notice any damage please report to the seller.
*Do not allow children to play with packing material!!!
Installing Hanging Bar
There are 2 L shaped hanging bars in to install your product,
provided with screws. Fix bars on product body via M5 x 35
screws into M5 turn screws (Figure 3).
M5 x 35 Ysb
Screws
Hanging bar
-16-
Figure 1
Figure 2
Figure 3
Usage of 3 Speed Digital Control
Peel protective papers out from the inox devices after assembly.
Speed Choice
The device has 3 degrees of ventilation. According to the cooking and frying steam, you can
choose low-middle-high ventilation levels. Buttons on the front panel are used for turning the
device on. The models with eletronic controllers have automatic timers. 15 minutes automatic
timer is turned on, when pressed any of the buttons, which starts the motor up, more than 2
seconds. When timer starts, display will signal and after 15 minutes motor will automaticly stop.
Please turn on hob and hood at the same time to activate circulation. This will provide positive
effect on vacuum power. Let the device run for a while after cooking process is finalised, thus the
remaining smell and steam will be absorbed.
2nd Speed 3rd Speed Lamp Button
Cleaning Periods of Aluminum Filter
Filter should be cleaned when “C” signal appears on the Display or each 2-3 weeks (in accordance
with the usage frequency). After cleaning and replacing filters to their places, button should be
pressed for more than 3 seconds (when the product is off) in order to remove the “C” signal. “E”
signal will appear on Display and product will start working at normal position. If you want to
continue using your product without removing “C” signal, active speed will appear for 1 second
when you press
button, then “C” signal will appear once more and the motor will continue operating.
Illumination
The product has 2 lamps and one lamp button to operate illumination. Press lamp button in
order to start illumination.

-6-
Installing Plastic Outlet
Install plastic outlet to top of motor cabin via 3,5x9,5 screws
(Figure 4).
3,5 x 9,5 RYSB
Screws
Ø 8 mm
Ø 6 mm
Drilling Mounting Holes
Attach mounting schemeon the wall and drill holes on points
marked as A,B,C via Ø8 mm driller. To install chimney part, use
Ø6 mm driller by taking reference of min./max. height
dimensions .
WARNING : During drilling the hanging holes , please pay attention to the diameter of the
holes to be used for hanging the hood.
If the diameters of hanging holes are not as pointed , the hood can not be assembled properly.
Hood Hanging
Holes
Ø 8 mm
Outlet Connection
Holes
Ø 6 mm
A
B
C
D
E
Nailing Dowels
Nail Ø10 mm dowels into A,B,C holes drilled as Ø8 mm.
Place Ø6 mm dowels on two holes, drilled as Ø6 mm
(Figure 5)
3120-3170 models / for 80-90cm models, drill holes on
points marked as G,H and nail Ø10 mm dowels into it.
10 mm Plastic
dowel
6 mm Plastic
dowel
PROGRAMMABLE OPTIONS
Programmable options can be set when motor and lamp is closed and not set.
1-Back light brightness settings: When – button is pushed for approximately 5 seconds blue
color percentage appears on the screen (for example: b 00). When V- button is pushed once more
red color percentage will appear on the screen. (for example: r100) When V- button is pushed
once more green color percentage will appear on the screen. (for example: g10). Pressing Tmr+
and Tmr- buttons (pressing for longer time it can be set fast) the color whose percentage appears
on the screen can be set between 0 and 100. New color is set pressing – button for 5 seconds
(beep sound is heard) and settings mode will be left. In order to leave settings mode without
setting an option, on/off or lamp buttons can be pushed.
2-Back light option: Back light is always at on position. Keeping + button pressed for 5 seconds
(beep sound will be heard) when motor and lamp is off and not set (that is when the chimney hood
is not operating) back light can be set so that it will be off. In order to set back light to be on
constantly + button should be pressed for approximately 5 seconds.
Blue (%) Red (%) Green (%) Color
Light Turquoise
Light Green
Green
Blue
Purple
Red
Colourless screen
Orange
-15-
Figure 4
Figure 5
G
H
TECHNICAL SPECIFICATIONS
Feeding Voltage 220-240 V 50Hz
Motor Isolation Class
Isolation Class
F
CLASS I

-7-
A
B
C
D
E
Chimney Fixing Bar Screws;
Drill holes on the wall via Ø6 mm driller. Fix the chimney fixing
bar via 3,9 x 22 Ysb screws on Ø6 mm plastic dowels.
Drill holes on the wall via Ø10 mm driller. Fix 2 pcs of 5,5 x 60
Ysb screws on A,B points on Ø10 mm plastic dowels.
The distance between the wall and screw top should be 5mm.
Figure 6
5,5 x 60 Ysb
Screw
3,9 x 22 Ysb
Screw
Placing Range Hood on The Wall
Hang L shaped hanging bars on A and B points (Figure 7)
A
B
DE
DE
A
B
Note: You may fine tune parallelism by easing M5 screws on
the top.
Motor
on/off
Lamp
on/off
Timer
step
-14-
5 Speed LCD Control Usage
On/Off Button: ( ) This button starts and stops the motor. Starting speed of the motor is 2nd
speed.
–Button: Decreases speed. Speed can be reduced till 1st speed. When you press this button
longer, 1 speed level is decreased each half seconds.
+ Button: Increases speed. Speed can be increased up to 5th Speed. When you press this button
longer, 1 speed level is increased each half seconds. When the cooker hood is set to 5th speed,
motor will operate at 5th speed for 15 minutes then will continue operating at 2nd speed. 5th
speed is turbo speed.
Timer - Button: ( ) It is used for setting the time that timer will start operating decreasing the
time. Timer decreases 1 level at each press; if the button is pushed longer level will decrease fast.
Timer + Button:( ) It is used for setting the time that timer will start operating increasing the time.
Timer increases 1 level at each press; if the button is pushed longer level will increase fast.
Cooker-hood has timer function for two different
usages:
1-Timer for stopping the cooker-hood: If the timer is set when the motor is operating, cooker-hood
will stop, lamp will be off and buzzer will ring for 5 seconds when timer period is over.
2-Timer for alarm: If the timer is set when the motor is not operating, alarm timer will have been
started. When the timer is over, buzzer will ring for 15 seconds; even though motor is operated or
the lamps are set to on position when the timer is operating, motor will not stop operating and lamp
will not be off. When timer is not set, timer clock shows the real time.
Clock: Clock on LCD screen shows actual time. Two points between the hour and the minute
flashes each 1 second. In order to set hour, Tmr+ ( ) and Tmr- buttons are pushed at the same
time. Hour and minute flashe for 5 seconds. During flashing, pressing Tmr+ ( ) or Tmr- ( )
button minute will operate changing clock. During flashing, hour can be set using Tmr- or Tmr+
buttons, time can be set. (Settings will be reset in case of electricity cut or failure)
Filter Cleaning Warning : Filter cleaning icon appear on the screen after the cooker hood is
operated for 60 hours and it flashes each second to remind to wash aluminum filter. Pressing
on/off button for 3 seconds, filter time can be reset and filter icon can be removed.
HOW TO USE BLUE LIGHT
When the product is powered on, the blue light at the middle panel will be on. In order to turn
off the blue light, you should keep the lamp buton pushed for 5 seconds. When the light is off,
if you push lamp buton for 5 seconds, blue light will be on. During that position, blue light will
be always on, when the product is off.
Tighten the Hanging Screws:
Tighten screws after hanging to fix your product via
screwdriver. You may use the M5x40Ysb screws to have fine
tune parallelism of hood. Figure 8
Figure 6
Figure 7
Figure 8
G
H

-8-
C
C
-13-
Illumination
The product has 2 lamps and one lamp button to operate illumination. Press lamp button in
order to start illumination.
Usage of 5 Speed Digital Control
Usage
Remove protective folio on the inox product after installation.
Speed Selection The product has 5 speeds of ventilation level. One of 1,2,3,4,5 speeds is
selected in accordance with steam of cooking or fry. Motor is started pressing control button
on the front panel. Speed is increased pressing button, and decreased by pressing button.
Automatic timer (TIMER) is available at the models with electronic remote control. When you press
button more than 2 seconds, timer function will be on for 15 minutes. When the timer is on,
Display will signal and the motor will be off automatically 15 minutes later. Please use the cooker
and the product at the same time to enable circulation. Doing so, air suction power will be affected
positively. We recommend you to operate your product for few minutes more after the cooking is
completed to enable absorption rest of smell and steam.
Cleaning Periods of the Aluminum Filters:
Filters should be cleaned when C signal appears on Display or (according to usage) each 2-3
weeks. In order to remove C signal, after the filters are cleaned and replaced to their place, press
button more than 3 seconds (when the product is at off position). Letter “E” will appear on
Display and the product will operate as normal. If you would like to continue using the product
without deleting C signal, when you press the button active speed will appear for
1 second, then C signal will appear once more and the motor will continue operating.
NOTE: C signal will appear after usage of the product for 60 hours.
Tighten the Hanging Screws:
Fix product onto wall from point C with 5,5x60 Ysb screw in
order to ensure your product is safely installed. Figure 9
Installing Aluminum Flexible Pipe:
Connect aluminum flexible pipe to outlets on the product and
kitchen wall.
Please make sure that this connection is strong enough not
to break when the hood is on in the highest level. Figure 11
Figure 9
Figure 11
Fix product onto wall from point G,H with 5,5x60 screws
in order to ensure your product is safely installed. Figure 10
G - H
3120-3170 models / for 80-90cm models;
Figure 10

-9-
D
E
External
chimney
Internal
chimney
3,5 x 9,5 RYSB
Nickel Screw
-12-
Usage of 3 Speed Digital Control
Peel protective papers out from the inox devices after assembly.
Speed Choice
The device has 3 degrees of ventilation. According to the cooking and frying steam, you can
choose low-middle-high ventilation levels. Buttons on the front panel are used for turning the
device on. The models with eletronic controllers have automatic timers. 15 minutes automatic
timer is turned on, when pressed any of the buttons, which starts the motor up, more than 2
seconds. When timer starts, display will signal and after 15 minutes motor will automaticly stop.
Please turn on hob and hood at the same time to activate circulation. This will provide positive
effect on vacuum power. Let the device run for a while after cooking process is finalised, thus the
remaining smell and steam will be absorbed.
2nd Speed 3rd Speed Lamp Button
Cleaning Periods of Aluminum Filter
Filter should be cleaned when “C” signal appears on the Display or each 2-3 weeks (in accordance
with the usage frequency). After cleaning and replacing filters to their places, button should be
pressed for more than 3 seconds (when the product is off) in order to remove the “C” signal. “E”
signal will appear on Display and product will start working at normal position. If you want to
continue using your product without removing “C” signal, active speed will appear for 1 second
when you press
button, then “C” signal will appear once more and the motor will continue operating.
Illumination
The product has 2 lamps and one lamp button to operate illumination. Press lamp button in
order to start illumination.
Installing the External Chimney:
Place internal chimney into external chimney. Place
chimneys to motor box and push it downward. Make
sure that the connection between the body and motor
box is so tight.Figure 12
Installing internal chimney
Pull internal chimney upwards through the external
chimney. Fix the chimney with 3,5 x 9,5 nickel
covered screws.Figure 13
After complete the installing the hood, please check all the connections before operate it.
Please take off the protective folio from you product.
Figure 12
Figure 13
Touch Button Explanation
Speed Choice : Your device has 3 speed level. Depending on the cooking and frying steam , you
should run the device with low- medium or high Speed.The device turned on with the control button
on the front panel. In the models with the electronic control there is a TIMER function.
Tımer
If you press one of the control buttons for more than 2 seconds , the LED illumination will blink for a
moment as a sign of turnin on of the TIMER. After 15 minutes the engine will stop automatically
Lamp
1.Speed 2.Speed 3.Speed
Illumination
The product has 2 lamps and one lamp button to operate illumination. Press lamp button in order to
start illumination.

-10-
Replacing the Lamps
Cut off the connection of the cooker hood with electricity. Take off the aluminum cassette filter. Take
off the failed lamp and replace it with a new one that is of the same rating. (Please wait for the lamps
to cool as they might hurt your hand.)
Replacing 50W Halogen Lamp
In order to change halogen lamps, take the lamp downwards
pushing back of lamp holder downwards and then turning it a
little bit anti-clockwise take it off downwards. Figure 14
Replacing 20 W Lamps
In order to replace halogen lamps, hold one lamp, as shown in
and turn it to left tor right. Bring the lamp pin in the same line
with socket and pull towards yourself.Remove glass cover as
shown in Picture with an object, which would not scratch
product's surface . To remove pull the faulty lamp down, and
replace with a new one. Figure 15
Functions of the Product
Your hood is compatible for use with our without chimney.
Usage with chimney
The product should be connected to a chimney that will direct the air out during usage with chimney. In
order to achieve best performance, pay attention that the duct system follows the shortest way for
connection to the chimney. Your product is produced as it will be appropriate for usage with chimney.
Attention!!!
Outlet of the product should not be connected to air canals that have other smoke as well.
Active Carbon Filter
To provide air recirculation where product's chimney air outlet cannot be connected to exterior, it
is necessary to use active carbon filter with your product. You may purchase this accessory from
authorized sellers and after sales services
-11-
Carbon Filter Usage
Your product is compatible with two types of carbon filters.
You may see following information on how to use carbon filters.
Before installing or replacing carbon filter, first you should cut your product's power off.Carbon
filters should be replaced with a new one each 3-5 months because it is used at kitchens that does
not have chimney outlet.
Carbon filter should never be washed.
Grease filters should be installed on the product even when carbon filter is not in use. Do not use
your product without grease filter.
Replacing Carbon Filter
It is necessary to install 2 carbon filters to your product.
To place the carbon filter, place your filter on connection channels on motor and turn it
clockwise.In order to remove filter, turn it anti-clockwise. Figure 17
Changing Aluminum Cassette Carbon Filter
In order to take the carbon filter off, pull it towards yourself holding the upper latch. Figure 18
Figure 15
Figure 14
Figure 17
Figure 18
Replacing bulb
In order to change the bulb, turn it anti-clockwise and take it off.
Replace it with a new one in the same value by turning it in
clockwise. Figure 16
Figure 16