iLive ICP102B User manual

For Warranty Information and the most up-to-date version of this User’s Guide, go to www.iliveelectronics.com Customer Service: 1-888-999-4215
Copyright © 2012 Digital Products International (DPI, Inc.) All other trademarks appearing herein are the property of their respective owners. Specications are subject to change without notice.
Plug the included AC/DC power adapter into
the DCPOWERINPUT on the dock and
an AC power outlet to power the dock.
LINE IN
DC IN 5V
FM ANT
USER’SGUIDE
V:1024-0113-12
ICP102B Clock Radio for iPod and iPhone
Warning: Changes or modications to this unit not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
• The apparatus shall not be exposed to dripping or splashing and that no objects lled with
liquids, such as vases, shall be placed on apparatus.
L’appareilnedoitpasêtreexposéauxécoulementsouauxéclaboussuresetaucunobjetne
contenantdeliquide,telqu’unvase,nedoitêtreplacésurl’objet.
• Main plug is used as disconnect device and it should remain readily operable during intended
use. In order to disconnect the apparatus from the mains completely, the mains plug should
be disconnected form the mains socket outlet completely.
Laprisedusecteurnedoitpasêtreobstruéeoudoitêtrefacilementaccessiblependantson
utilisation.Pourêtrecomplètementdéconnectédel’alimentationd’entrée,laprisedoitêtre
débranchéedusecteur.
• Battery shall not be exposed to excessive heat such as sunshine, re or the like.
Lespilesnedoiventpasêtreexposéesàdefortechaleur,telqu’àlalumièredusoleil,aufeu
ouautreschosesdesemblable.
• Caution marking is located at the rear or bottom of the apparatus.
Attentionmarquageestsituésurlepaneauarrièreouinférieurdel’unité.
• The marking information is located at the rear or bottom of apparatus.
Lemarquageestsituésurlepaneauarrièreouinférieurdel’unité.
1. Read these Instructions.
2. Keep these Instructions.
3. Heed all Warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as
radiators, heat registers, stoves, or other apparatus
(including ampliers) that produce heat.
9. Do not defeat the safety purpose of the polarized
or grounding - type plug. A polarized plug has two
blades with one wider than the other. A grounding
type plug has two blades and a third grounding
prong. The wide blade or the third prong are
provided for your safety. When the provided plug
does not t into your outlet, consult an electrician
for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or
pinched particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus.
11. Only use attachments/accessories
specied by the manufacturer.
12. Use only with a cart, stand, tripod, bracket, or table
specied by the manufacturer, or sold with the
apparatus. When a cart is used, use caution when
moving the cart/apparatus combination to avoid injury
from tip-over. Unplug this apparatus during lightning
storms or when unused for long periods of time.
13. Refer all servicing to qualied
service personnel. Servicing
is required when the apparatus
has been damaged in any way,
such as power-supply cord or
plug is damaged, liquid has been
spilled or objects have fallen
into the apparatus, the apparatus
has been exposed to rain or
moisture, does not operate
normally, or has been dropped.
• CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE
BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
• WARNING:To reduce the risk of re or electric shock, do
not expose this apparatus to rain or moisture.
• AVERTISSEMENT: Pour réduire le risque d’incendie ou de choc
électrique, ne pas exposer cet appareil sous la pluie et l’humidité.
• CAUTION: Use of controls or adjustments or performance of procedures
other than those specied may result in hazardous radiation exposure.
• WARNING: Changes or modications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
• WARNING: Do not place the unit on top of any soft, porous, or sensitive surfaces to avoid
damaging the surface. Use a protective barrier between the unit and surface to protect the surface.
• WARNING: Use of this unit near uorescent lighting may cause interference
regarding use of the remote. If the unit is displaying erratic behavior move
away from any uorescent lighting, as it may be the cause.
• WARNING: Shock hazard - Do Not Open.
• AVIS:RISQUEDECHOCÉLECTRIQUE-NEPASOUVRIR
Mains plug is used as disconnect device and it should remain readily operable during
intended use. In order to disconnect the apparatus from the mains completely, the
mains plug should be disconnected form the mains socket outlet completely.
Laprisedusecteurestutilisépourdéconnecterlesystème.
Laprisedusecteurnedoitpasêtreobstruéeoudoitêtrefacilement
accessiblependantsonutilisation.Pourêtrecomplètementdéconnectéde
l’alimentationd’entrée,laprisedoitêtredébranchéedusecteur.
Do not mix old and new batteries.
Do not mix alkaline, standard (carbon-zinc), or rechargeable (ni-cad, ni-mh, etc) batteries.
Nomezclebateríasviejasynuevas.
Nomezclebateríasalcalinas,estándar(carbono-zinc)orecargables(ni-cad,ni-mh,etc.).
WARNING: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-
SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE
PERSONNEL.
ATTENTION
RISQUE D' ÉLECTROCUTION
NE PAS OUVRIR
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and maintenance
(servicing) instructions in the literature
accompanying the appliance.
This symbol indicates that this product
incorporates double insulation between hazardous
mains voltage and user accessible parts.
The lightning ash with arrowhead symbol,
within an equilateral triangle, is intended to alert
the user to the presence of uninsulated “dangerous
voltage” within the product’s enclosure that may
be of sufcient magnitude to constitute a risk of
electric shock to persons.
IMPORTANT SAFETY INSTRUCTIONS
Introduction and Setup
FCC Warnings
Power
The battery backup is intended for
short power outages only. The clock
radio’s primary functions cannot run
off of the battery backup alone.
Requires 2, AAA-size, batteries (not included)
OPEN
Battery Backup
Additional Warnings
WARNINGS AND PRECAUTIONS
M
S
POWER SOURCE / TIME SYNC
CLK / ALA 1 / 2
– TUNE +
DIMMER
VOLUME
SNOOZE
OPEN
LINE IN
DC IN 5V
FM ANT
Volume
Press to adjust
the volume.
Source/TimeSync
Press to switch
between iPod,
FM Radio, and
Line In modes.
Press and hold
to sync the time
from a docked
iPod or iPhone.
M/Clk/Ala1/2
In FM Radio mode,
press to begin saving
the current radio
station as a preset.
Press and hold to
autosave preset
channels.
In Off mode, press
and hold to begin
setting the clock.
Press to begin
setting the alarm.
iPodDock
Tune+/-
Press to tune the radio
in FM Radio Mode.
Press and hold to
search for the next
available frequency.
Power
Press to turn the
unit on or off.
Dimmer/Play/Pause
Press and hold to
adjust the brightness
of the display.
Press to play or
pause a docked
iPod or iPhone.
In FM Radio Mode,
press to cycle through
preset radio stations.
Snooze/Sleep
Press to set the sleep timer.
Press to delay the alarm.
LineIn
FMAntennaWire

For Warranty Information and the most up-to-date version of this User’s Guide, go to www.iliveelectronics.com Customer Service: 1-888-999-4215
Copyright © 2012 Digital Products International (DPI, Inc.) All other trademarks appearing herein are the property of their respective owners. Specications are subject to change without notice.
1. Press the Power button
to turn the unit off.
2. Press and hold the M/Clk/Ala1/2
button until the display begins to
blink, then release the button.
3. Press the Tun+/-button to adjust the hour.
4. Press the M/Clk/Ala1/2button.
5. Press the Tun+/-button to
adjust the minute.
6. Press the M/Clk/Ala1/2button
to nish setting the time.
1. Press the Power button
to turn the unit off.
2. Press the M/Clk/Ala1/2button
to select Alarm 1 or Alarm 2.
3. To begin setting the selected alarm,
press and hold the M/Clk/Ala1/2
button until the display begins to
blink, then release the button.
4. Press the Tun+/-button to adjust the hour.
5. Press the M/Clk/Ala1/2button.
6. Press the Tun+/-button to
adjust the minute.
7. Press the M/Clk/Ala1/2 buttons to switch
between FM Radio, iPod, Buzzer, or Off.
The display will indicate the
following: IPod-iPod, bU-Buzzer,
rAd-FM Radio, oFF-Alarm Off
8. Once the set alarm time is reached,
the alarms will sound.
To set the other alarm, follow
the above steps and choose
the alarm not currently set.
1. Connect the iPod or iPhone to
the connector inside the Dock
for iPod and iPhone.
2. When the dock is plugged in,
using AC power, the docked
iPod or iPhone will charge.
Clock and Sleep Timer
Alarm
iPod and iPhone
Setting the Clock
1. Press the Power button
to turn the unit on.
2. Press the Snooze/Sleep button
repeatedly to set the sleep timer
( 90, 80, 70, 60, 50, 40, 30,
20, 10, 5, 3 min or OFF ).
3. Once the set sleep time has expired
the unit will automatically power off.
Setting the Sleep Timer
Setting the Alarm
After the alarm sounds:
Press the Snooze/Sleep button to
delay the alarm for several minutes.
OR
Press the Power button to turn the alarm off
until the set alarm time is reached again.
Snooze and Alarm Reset
Docking an iPod or iPhone
1. Follow the instructions for
Docking an iPod or iPhone.
2. Press the Source/TimeSync
button to switch to iPod mode.
3. Press the Play/Pause button to begin
playing the docked iPod or iPhone.
Playing a Docked iPod or iPhone
1. Follow the instructions for
Docking an iPod or iPhone.
Note: Auto time sync will not work
with some older model iPods.
2. Upon initial use, the clock will
automatically sync to the time of
the docked iPod or iPhone.
3. After initial use, press and hold the
Source/TimeSync button to sync the
time from the connected iPod or iPhone.
Auto Time Sync
To download this User’s Guide in English,
Spanish, or French, or to get answers to
frequently asked questions, visit the support
section at: www.iliveelectronics.com
Para descargar este Manual del
Usuario en inglés, español y francés, o
para obtener respuestas a preguntas
frecuentes, visite la sección de apoyo
en www.iliveelectronics.com
Pour télécharger ce guide de l’utilisateur
en anglais, espagnol ou français, ou pour
obtenir des réponses à des questions
fréquemment posées, consultez la rubrique
d’assistance sur www.iliveelectronics.com
International Support
Requires a 3.5mm audio cable (not included)
1. Connect a 3.5mm audio cable to the
LineIn on the unit and an audio output
on an MP3 player or other audio source.
2. Press the Source/TimeSync
button to switch to Line In mode.
The display will show “AU”.
3. Use the native controls on the
connected MP3 player or other audio
source to play and control audio
played through the clock radio.
1. Press the Powerbutton
to turn the unit on.
2. Press the Source/TimeSyncbutton
to switch to FM Radio mode.
3. Press the Tun+andTun-buttons to
adjust the radio to the desired frequency.
4. Press and hold the Tun+and
Tun-buttons to search for the
next available frequency.
5. Press the Vol+/- buttons
to adjust the volume.
6. Press the Powerto turn the radio off.
Adjust the position of the FM wire
antenna to improve FM radio reception.
1. Follow the instructions for
Tuning the FM Radio.
2. Tune to the desired station.
3. Press the M/Clk/Ala1/2 button.
4. Press the Tun+/-buttonsto
choose the preset number.
5. Press the M/Clk/Ala1/2button
to save the station as a preset.
Up to 20 stations may be
saved as presets.
1. Follow the instructions for Tuning the
Radio and Saving a Station as a Preset.
2. Press the Play/Pausebutton to cycle
through preset radio stations.
1. Follow the instructions for
Tuning the Radio.
2. Press and hold the M/
Clk/Ala1/2button.
3. The unit will scan for an available station,
and save it as a preset. It will then scan
for the next available station, and set
that as the next preset, continuing until
up to 20 stations are saved as presets.
Line In
Using the Line In
Radio
Tuning the FM Radio
Saving a Station as a Preset
Autosaving Preset Radio Stations
Tuning Preset Radio Stations
To get information on which iPod, iPhone,
or iPad products are compatible with this
product, go to www.iliveelectronics.com.
For Warranty Information and the most
up-to-date version of this User’s Guide,
go to www.iliveelectronics.com.
Compatibility
Warranty
Table of contents
Other iLive Clock Radio manuals

iLive
iLive INTELLI SET IC600B User manual

iLive
iLive ICP200B User manual

iLive
iLive ICP232B User manual

iLive
iLive IC109 User manual

iLive
iLive ICP360 User manual

iLive
iLive ICP601B User manual

iLive
iLive ICP310B User manual

iLive
iLive IKBC384S User manual

iLive
iLive ICP122W User manual

iLive
iLive ICP360 User manual