iLiving ILG8MF72-430 User manual

1
72 Inches BLDC Mobile Fan
MODEL: ILG8MF72-430
Owner’s Manual
PLEASE READ AND
SAVE THESE INSTRUCTIONS

2
TABLE OF CONTENTS
Important Instructions………………………………………. 3-4
Specifications and Wiring Diagram………………………... 5
Parts of the FAN ……………………….………………… 6
Unpacking & Installation Instructions……………… ......… 7-11
Operating Instructions……………………….………....… 12-13
Maintenance and Cleaning………………………………. 13-14
Troubleshooting……………………………………………. 14
Warranty……………………………………………............. 15

3
IMPORTANT INSTRUCTIONS
CAUTION: Please read and save these instructions. Read carefully before attempting
to assemble, install, operate or maintain the product described. Do not use the fan if
any part is damaged or missing. Automatic reset safety device in motor. To reduce
risk of injury disconnect power supply before servicing.
Protect yourself and others by observing all safety information. Failure to comply
with instructions could result in personal injury and/or property damage!
Retain instructions for future reference.
WARNING: To reduce the risk of fire or electric shock, do
not use this fan with any solid-state speed control device.
This appliance has a grounded plug. To reduce the risk of
fire or electric shock, this plug is intended to fit in an
outlet only one way. If the plug does not fit into the outlet,
contact a qualified electrician. Do not attempt to bypass
this safety feature.
WARNING: To Reduce The Risk Of Fire, Electric Shock Or Injury To Persons, Do Not Use
Replacement Parts That Have Not Been Recommended By The Manufacturer (e.g. Parts
Made At Home Using A 3D Printer).
General Safety Information
NOTE: To comply with UL507, BLDC Mobile Fan is not to be used in
unattended areas.
1. Ensure that the power source conforms to the electrical requirements of the fan.
2. Where a two-prong wall receptacle is encountered, it must be replaced with a
properly grounded three prong receptacle installed in accordance with the United
States National Electrical Code (NEC) and all applicable local codes and ordinances.
This work must be done by a qualified electrician, using copper wire only.
3. Where possible, avoid the use of extension cords. If they must be used, minimize
the risk of overheating by ensuring that they are UL Listed and of the proper gauge
and length. Never use a single extension cord to operate more than one fan.
4. Do not kink the cord or allow it to contact oil, grease, chemicals, hot surfaces, or
sharp or abrasive objects.
5. This fan is to be operated ONLY with its OSHA compliant guards in place to prevent
persons and/or objects from contacting the revolving propeller. Any other use voids
warranty and may create unsafe conditions.
6. Fan is intended for general air circulation ONLY. It must NOT be used in potentially

4
dangerous locations such as flammable, explosive, chemical-laden. Do not attach
ductwork to the fan.
7. Always unplug fan before removing guard, as motor may restart unexpectedly.
8. Do not operate any fan with a damaged cord or plug. Discard fan or return to an
authorized service facility for examination and/or repair.
9. Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or
similar coverings. Do not route cord under furniture or appliances. Arrange cord
away from traffic area and where it will not be tripped over.
10. Disconnect the fan when moving it from one location to another.
11. Make sure the fan is on a stable, flat surface while it is in operation.
12. Disconnect the fan when removing the guards for cleaning.
13. Do not use in Outdoors.
1. Use of a three-prong to two-prong adapter is not recommended.
Improper connection may create the risk of electrocution. Use of such
adapters is prohibited in Canada.
2. Do not depend on any switch as the sole means of disconnecting
power when installing or servicing the fan. Failure to do so may result in
fatal electrical shock.
3. Do not insert fingers or foreign objects into the fan. Do not block or
tamper with the fan in any manner while it is in operation.
4. Do not touch motor. May be hot enough to cause injury.
5. Unplug prior to servicing unit.
6. To reduce the risk of fire or electric shock, do not use this fan with any
speed control device.
SAVE THESE INSTRUCTIONS

5
SPECIFICATION AND WIRING DIAGRAM
Wiring Diagram
CAUTION: There is no user maintenance part inside Control BOX or
Motor except regular cleaning as following description. All other
servicing or maintenance should be performed by qualified service
personnel.
Specification
Model
ILG8MF72-430
Size(Feet)
6
Voltage (V)
120
Frequency (Hz)
60
AMPS (A)
6
Wattage (W)
450
Max Speed (RPM)
300
Net Weight (lbs)
397

6
PARTS OF THE FAN
Note: The big fan has been fully assembled except the Tilt Knob(SP-M72-9),
Handle(SP-M72-10) , Caster Assembly-L/-R(SP-M72-7)&(SP-M72-8) and the
Control Box(SP-M72-6).
NO.
PART
QTY
DESCRIPTION
NO.
PART
QTY
DESCRIPTION
1
SP-M72- 1
8
Grill
7
SP-M72-7
2
Caster Assembly-L
2
SP-M72-2
1
Logo Cover
8
SP-M72-8
2
Caster Assembly-R
3
SP-M72-3
6
Fan Blade
9
SP-M72-9
2
Tilt knob
4
SP-M72-4
1
Frame Tubing
10
SP-M72-10
4
Handle
5
SP-M72-5
1
Side Grill
6
SP-M72-6
1
Control Box
1
2
3
4
5
6
9
7
8
10

7
UNPACKING &
INSTALLATION INSTRUCTION
Loosen all the screws from
the horizontal fence on the
front and back side.
Loosen all the screws from the fixed
board on the left and right side.
Take off all the fixed board.
The fixed board.
Screws

8
Remove the top cover carton, then remove the carton around the fan.
Take off the control box from the fan head and take out the accessories
from the frame tubing of the fan.
Lift up the fence, and pull it out slowly.
Control box
Accessories

9
Caster Assembly Installation Instructions
1. Loosen the screws from the base of the frame tubing.
2. Insert the caster assembly (SP-M72-7)&(SP-M72-8) into the base of
the frame tubing to the end.
3. Tighten the screws from step #2 again.
Caution：There is a break on the Caster Assembly. When you finish the installation,
please lock down the break before power on the fan.
Loose this screw.
The break is Lock down.
The break is Open.

10
Loosen the screws and pull out the holding boards and vertical fences.
Lift up one side of the fan and hold on, then pull out the floor plate.
Tilt Knob & Handle Installation Instructions
1. Loosen the screws from the frame tubing, insert the Tilt
Knob(SP-M72-9) and then tighten the screws.
Loose this screw.

11
2. Align the handles(SP-M72-10) with the mounting hole on the
frame tubing and tighten them. There are 3 mounting holes on each
side, which can be selected according to your preference.
Control Box Installation Instructions
1. Loosen the screws from the mounting plate, hang up the control
box(SP-M72-6) to the mounting plate. Make sure all screws are tighten.
2. Insert the power connector to the control box(SP-M72-6).
Power Connector
from the fan.
Loosen the screws.

12
OPERATION INSTRUCTION
Control Box
1. This fan employs the latest technology of EC (electronic commutator)
and electronic control.
2. Switch On the fan, the LCD screen will light up and display “0 RPM”.
3. Speed adjustment by the adjustment knob. Speed is continuously
variable from 100 (min) to 300 (max) rpm.
4. Turn the knob in clockwise direction will speed up the fan and
counter-clockwise will slow down the fan until stop.
5. Adjust the fan speed to your desire comfortable rate. Turn the knob
slowly as the fan requires time to speed up or slow down.
PART
DESCRIPTION
1
LCD Screen
2
Overload Protection
3
Air Adjustment knob
4
Power Switch
1
2
3
4

13
CAUTION:
Rotation will always have some natural resonance frequency. This fan has
a wide spread of speed adjustment which may have encounter this
resonance at one or two speeds.
At a speed when resonance occurs, the whole fan will vibrate somewhat
vigorously and with shaking noise.
When you notice the fan is vibrating, this may be the resonance. Too
much resonance will damage the fan. Please skip this speed and you will
see the fan ceases vibrating immediately.
Resonance is nature physical phenomenon. Please skip the speed that
will cause the resonance.
MAINTENCE AND CLEANING
WARNING:Parts replacement and troubleshooting to be performed only
by qualified personnel.
WARNING:Do not depend on any switch as the sole means of
disconnecting power when installing or servicing the fan. Failure to do so
may result in fatal electrical shock.
WARNING:Unplug the fan from the wall outlet before servicing or
cleaning.
CAUTION: There is no user maintenance part except regular cleaning as
following description. All other servicing or maintenance should be
performed by qualified service personnel.
To clean the fan, use a soft damp cloth. Wipe down with a dry cloth.
Do not use cleaners that are harmful to paints or plastics.
CAUTION: Do not use gasoline, benzene, thinner, harsh cleaners, etc.,

14
which are dangerous and will damage the air circulator.
The propeller, guard, and motor should be cleaned periodically to
prevent overheating, and/or operating in an imbalanced condition.
CAUTION: If cleaning requires the removal of a guard, remove only the
front guard and re-install when finished in its originally installed position.
Do not repair propeller if it becomes damaged. The propeller is
accurately balanced at the factory and should be replaced if damaged.
Do not bend the propeller. The propeller is accurately balanced at the
factory and should be replaced if damaged.
Do not repair propeller if it becomes damaged.
Motor is permanently lubricated.
TROUBLE SHOOTING
If your fan fails to operate, please follow these Instructions:
1. Make sure the fan is plugged in and the electrical outlet is working
properly.
2. Check for any obstruction. If you find an obstruction, turn the fan
“OFF”. Unplug the fan and carefully remove the obstruction.
Plug the fan in and turn it on again. It should resume normal operation.
NOTE: IF YOU EXPERIENCE A PROBLEM WITH YOUR FAN, PLEASE DO NOT
ATTEMP TO OPEN OR REPAIR THE FAN YOURSELF. DOING SO COULD
CAUSE DAMAGE TO THE FAN AND/OR PERSONAL INJURY. Always consult
the manufacturer before further use.

15
Warranty Information
This product comes with a 1-YEAR LIMITED COMPONENT WARRANTY. If your unit
does not appear to be working properly, please contact our service center by calling
1-800-317-1688. Prior to your call, we encourage you to visit our service related
website www.ilivingusa.com for troubleshooting tips and service instructions if
needed.
Register your product at our website:
Or visit iLivingUSA.com/register-product
Feedback
Love it? Help us make the product more for you.
Let us know with a customer review.
Please visit: https://www.amazon.com/review/review-your-purchases#
At iLiving USA, we are committed to bringing top quality products to our customers.
iLIVING USA
860 Mahler Road,
Burlingame, CA 94010
Tel: [phone]
Email: [e-mail]