Iluminarc Ilumipanel 180 User manual

Ilumipanel 180 IP Optic RGB
Quick Reference Guide

Ilumipanel 180 IP Optic RGB QRG
2
About This
Guide
The Ilumipanel 180 IP Optic RGB Quick Reference Guide (QRG) contains
the product’s connection and mounting information, as well as the menu
options and DMX values.
Disclaimer
Refer to this product’s User Manual for detailed information and
instructions. You can download the User Manual from the ILUMINARC
website: www.iluminarc.com.
Read ALL the disclaimers and Safety Notes in this document, as well as
those in the product’s User Manual before installing, operating, and
maintaining this product.
Safety Notes
•
DO NOT open the product unless instructed. It contains no
user-serviceable parts.
•DO NOT look at the light source when the product is on.
•DO NOT touch the product when operating because it may be hot.
•DO NOT leave any flammable material within 50 cm from the product
while operating or connected to the power outlet to minimize the risk of
fire.
•DO NOT mount the product overhead without using a safety cable.
•DO NOT submerge this product (IP66). Regular outdoor operation is
fine.
•DO NOT operate the product if you see damage on the housing, lenses,
or cables. Have an authorized technician replace the damaged parts.
•DO NOT connect the product to a dimmer or rheostat.
•ONLY connect the product to a grounded and protected circuit.
What Is
Included
•One Ilumipanel 180 IP Optic RGB
•One Power Input Cable (bare-ended)
•One Data Input/Output Cable (bare-ended)
•One Warranty Card
•
One Quick Reference Guide

Ilumipanel 180 IP Optic RGB QRG
3
Features
•1, 3, 4, 6, or 7-channel DMX RGB LED wash product
•Operating modes:
1-channel: Dimmer
3-channel: RGB control
4-channel: Dimmer, RGB control
6-channel: RGB control per module (two modules)
7-channel: Dimmer, RGB control, color macros, strobe, dimmer
speed
•Five distinct dimming curves
•Dual Vector Array LED panel positioning
•High-power 5 W (700~1,000 mA) RGB LEDs
•IP66 with 316 stainless steel hardware
•GORE valve
• Cast and extruded aluminum with Integrated Cooling Enhancement
Options
•
Ilumicode addresser (for product configuration)
•The RDM2go, which includes a built in Ilumicode addresser along
with many other useful features is now available.
•The Ilumicode addresser is required for product configuration
(sold separately).

Ilumipanel 180 IP Optic RGB QRG
4
AC Power
This product has an auto-ranging power supply that works with an input
voltage range of 100~240 VAC, 50/60 Hz.
Power Wiring
To provide power, you have two options:
•Connect the bare-ended, IP66-rated power cable from the product
to an IP66-rated power connector.
•Use an IP66- rated junction box. If so, make sure to use IP66-
rated
conduit.
Iluminarc recommends always using conduit for underground wiring of
any kind.
Power
Cable Table
Connection Wire (US) Wire (Europe) IP66 Pin
AC Live
Black
Brown
1
AC Neutral
White
Blue
2
AC Ground
Green/Yellow
Green/Yellow
3
AC Power Junction
Box Wiring

Ilumipanel 180 IP Optic RGB QRG
5
DMX
Connection
This product provides a DMX 512 connection by using bare-ended,
IP66-rated signal cable. This cable comes connected to the product.
Signal Wiring
To provide the signal, you have two options:
•Connect the bare-ended, IP6- rated signal cable from the product
to two IP66-rated signal connectors (DMX In and DMX Out).
•Use an IP66-rated junction box. If so, make sure to use
IP66-rated conduit.
The signal cable must match or exceed the ele
c
trical characteristics of
the Belden 9841 cable for EIA RS
-485 applications. You can
also use CAT
5, CAT
5e, or CAT 6.
DMX
Junction Box
Wiring
DMX Cable Table
Connection DMX In DMX Out IP66 Pin
Ground
Shield
Shield
1
Data -
Black
Green
2
Data +
White
Red
3

Ilumipanel 180 IP Optic RGB QRG
6
Ilumicon and
DMX
Controllers
To control/operate the Ilumipanel 180 IP Optic RGB, use either an Ilumicon
or a DMX controller. Use the standard DMX connection as shown in the
section, DMX Junction Box Wiring, to connect this product to any standard
DMX controller.
For more information, refer to the Ilumipanel 180 IP Optic RGB User
Manual.
Ilumicode
Configuration
To configure the Ilumipanel 180 IP Optic RGB, use the Ilumicode
addresser.
Ilumicode
Connections
The following diagram shows how to connect the Ilumicode to the product.
This connection will control multiple products at the same time. In addition,
all connected products will be assigned to the same DMX address.
To assign individual DMX addresses to each product, connect the Ilumicode
unit to each product individually. In addition, disconnect the DMX output of
the product being configured if other products are connected to it.
You must hardwire the Ilumicode directly to the Ilumipanel 180 IP
Optic
RGB when programming the product.
Ilumicode
Connection
Diagram
ILUMINARC suggests connecting no more than 20 products in this mode,
keeping the total distance to less than 60 m (197 ft). For greater, you may
need to use an optically isolated signal amplifier.

Ilumipanel 180 IP Optic RGB QRG
7
Mounting
Before mounting this product, read the Safety Notes at the beginning of the
Ilumipanel 180 IP Optic RGB User Manual and follow the mounting
procedures.
Mounting Diagram
Mounting Points

Ilumipanel 180 IP Optic RGB QRG
8
Ilumicode
Control Panel
Description
Button Function
<POWER>
Turns the Ilumicode unit on.
<MENU>
Scrolls through the main level or exits from the current menu
or function.
NOTE: Press and hold to turn the unit off.
<ENTER>
Enables the currently displayed menu or sets the currently
selected value into the selected function.
<UP>
Navigates upwards through the menu options and increases the
numeric value when in a function.
<DOWN>
Navigates downwards through the menu options and decreases
the numeric value when in a function.
Start Address
To ensure full access to all channels in each DMX mode, the highest
recommended DMX addresses are as follows:
Mode Address Mode Address Mode Address
ARC FULL
506
AR1.D
509
SPECIAL 1
507
ARC1
510
SOLID
512

Ilumipanel 180 IP Optic RGB QRG
9
Menu Options
Main Level
Programming Levels
Description
DMX 001~512 N/A Sets the DMX starting address
PERSON
ARC 1
N/A
3-channel: RGB control
ARC 1 + D
4-channel: RGB control +
dimmer
ARC FULL
7-channel: RGB control +
dimmer
REMOTE
Allows using the ILUMICON
unit
SOLID
1-channel: dimmer
SPECIAL 1
6-channel RGB per module
CALIB
WHITE (1~11) RED
GREN
BLUE 0~255
Determines the white balance
for the color macros
RGBTOW
Determines the white balance
when RGBTOW is active
DIMMER
OFF
N/A
Dimmer works in linear mode
DIM 1
Dimmer works in non-linear
mode, from fast to slow
DIM 2
DIM 3
DIM 4
STATIC
RED
0~255 Configures the static color and
effect
GREN
BLUE
STRB
0~20
SETTINGS
COLOR
OFF
Maximum output, unbalanced
white
RGBTOW
White output is as per CALIB >
RGB settings
UC
Output matches that of
product’s previous versions
RESET NO/YES
Resets unit to factory default
settings

Ilumipanel 180 IP Optic RGB QRG
10
DMX Values
ARC FULL
Channel Function Value Percent/Setting
1
Dimmer
000 ó255
0~100%
2
Red
000 ó255
0~100%
3
Green
000 ó255
0~100%
4
Blue
000 ó255
0~100%
5 Color Macros
000
ó
010
011 ó030
031 ó050
051 ó070
071 ó090
091 ó110
111 ó130
131 ó150
151 ó170
171 ó200
201 ó205
206 ó210
211 ó215
216 ó220
221 ó225
226 ó230
231 ó235
236 ó240
241 ó245
246 ó250
251 ó255
No Function
R: 100% G: 0~100% B: 0%
R: 100~0% G: 100% B: 0%
R: 0% G: 100% B: 0~100%
R: 0% G: 100~0% B: 100%
R: 0~100% G: 0% B: 100%
R: 100% G: 0% B: 100~0%
R: 100% G: 0~100% B: 0~100%
R: 100~0% G: 100~0% B: 100%
R: 100% G: 100% B: 100%
White 1
White 2
White 3
White 4
White 5
White 6
White 7
White 8
White 9
White 10
White 11
6 Strobe
000 ó009
010 ó255
No Function
Slow~Fast
7 Dimmer Speed
000 ó009
010 ó029
030 ó069
070 ó129
130 ó189
190 ó255
Uses Ilumicode Settings
Off
Speed 1 (Fastest)
Speed 2
Speed 3
Speed 4 (Slowest)