iNels RF KEY-40/W User manual

WIRELESS LIGHT DIMMER
KEY FOB
Combination of iNELS switching element for universal use. It can be used to control
electrical appliances, lights, sockets, garage doors, etc.
EN

Content
The individual elements in the iNELS set are paired and their functions are preset.
iNELS kit with key fob enables the basic function of controlling electrical appliances - ON / OFF.
The appliances can be controlled independently by a key fob.
Controller – key fob RF KEY-40/W, RF KEY-40/B
ON function of
switching unit no. 1
OFF function of
switching unit no. 1
ON function of
switching unit no. 2
OFF function of
switching unit no. 2
EAN 8595188183109 (key fob - black + Universal dimmer, 1-channel)
EAN 8595188183116 (key fob - white + Universal dimmer, 1-channel)
EAN 8595188183123 (key fob - black + 2 x Universal dimmer, 1-channel)
EAN 8595188183130 (key fob - white + 2 x Universal dimmer, 1-channel)
Universal dimmer, 1-channel
RFDEL-71B-SL
The settings of the wall controllers can be changed - see detailed manuals of iNELS elements.

+
123
RF KEY 40
+
RF KEY 40/B – key fob , black
RF KEY 40/W – key fob , white
Detailed manual
Characteristics
• Key fob-sized remote control - used to control, lights, gate, garage door, shitters, etc.
• 4 buttons, each of which allows you to control an unlimited number of components.
• Replaceable battery (3 V CR 2032 - included in the package) with a service life of approx. 5 years (depen-
ding on the frequency of use).
Insertion and replacement of a battery RF KEY-40
Safe handling
When handling a device unboxed it is important to avoid contact with liquids. Never place the device
on the conductive pads or objects, avoid unnecessary contact with the components of the device.
Use a coin to open the key fob and
remove the front cover. Carefully tap
the device out of the bottom cover.
Slide the CR2032 battery into the
battery holder. Observe the polarity.
Insert the device into the bottom
cover. Attach the front of the cover
and click.
Controller – key fob
RF KEY-40/W, RF KEY-40/B

RF KEY-40
Supply voltage:
Battery life:
Transmission indication:
Number of buttons:
Communication Protocol:
Frequency:
Signal transmission method:
Range:
Other data
Operating temperature:
Operating position:
Colour design
Protection:
Pollution degree:
Dimensions:
Weight:
Related standards:
3 Vbattery CR2032
about 5 years depending on the frequency of use
red LED
4
RFIO2
868.5 MHz
one-way addressed message
in the open up to 200 m
-10 ... +50 °C (14 ... 122 °F)
any
white, black
IP20
2
64 x 25 x 10 mm
16 g
EN 60669, EN 300 220, EN 301489,
No 426/2000 Coll.
Technical parameters
Attention
When you install iNELS RF Control system, you have to keep a minimal distance of 1 cm (0.4“) between each
unit. Between the individual commands must be an interval of at least 1s.

RFDEL-71B-SL
Installation options
mounting in an installation box mounting into the ceiling light cover Under ceiling mounted
Detailed manual
Universal dimmer, 1-channel
RFDEL-71B-SL
Characteristics
• The universal built-in dimmer is used to regulate light sources.
• They can be combined with detectors, controllers, iNELS RF Control or system components.
• 7 light functions - smooth increase or decrease with time setting 2s-30 min. + additional function
SWITCH OFF
• Thanks to setting the min.brightness you will eliminate flashing of the LED and ESL light sources
• The universal dimmer may be controlled by up to 25 channels (1 channel represents 1 button).
• Connection of the existing button on the control input “S“ enables combination of wireless control
with classic (wired) control.
• The programming button on the controller is also used for manual control of the output.
• For components labelled as iNELS RF Control2(RFIO2), it is possible to set the repeater function
via the RFAF/USB service device.
• Range up to 200 m (in open space), if the signal is insucient between the controller and unit,
use the signal repeater RFRP-20 or protocol component RFIO2that support this feature.

RFDEL-71B-SLTechnical parametres
230 V AC / 50 Hz
5 VA
0.5 W
+10/ -15 %
4 - wire, with NEUTRAL
R, L, C, LED, ESL
2 x MOSFET
300 W *
868.5 MHz
up to 200 m
button PROG (ON/OFF), external button
-15 ... + 45 °C
-30 ... +70°C
any
IP30 under normal conditions
III.
2
screwless terminals
0.2-1.5 mm2
43 x 44 x 22 mm
30 g
EN 60730, EN 63044, EN 300 220, EN 301 489
Supply voltage:
Apparent power:
Dissipated power:
Supply voltage tolerance:
Connection:
Dimmed load:
Output:
Contactless:
Load capacity:
Control:
RF command from the transmitter:
Range in open space:
Manual control:
Other data:
Operating temperature:
Storage temperature:
Operating position:
Protection:
Overvoltage category:
Contamination degree:
Connection:
Connecting conductor:
Dimensions:
Weight:
Related standards:
* loadability of power factor cos φ=1

60 - 90 % 80 - 95 % 20 - 60 % 0 - 10 % 80- 90 %
x
RFRP-20
LED, ESL, R
L
N
L
L
N
C
L
N
Compatibility
The device can be combined with all system components, controls and devices of iNELS RF Control and
iNELS RF Control2.
The detector can be assigned an iNELS RF Control2(RFIO2) communication protocol.
Connection
coil transformer electronic transformer
Radiofrequency signal penetration through various construction materials
brick walls wooden structures
with plaster boards reinforced concrete metal partitions common glass
Range up to 200 m in open space, if the signal is insucient between the controller and unit, use the signal
repeater RFRP-20 or protocol component RFIO2that supports this feature.

Instruction manual is designated for mounting and also for the usage of the device. It is always a part of its pac-
king. Installation and connection can be carried out only by a person with adequate professional qualification
with understanding this instruction manual and functions of the device, and while observing all valid regulations.
Trouble-free function of the device also depends on transportation, storing and handling. In case you notice any
sign of damage, deformation, malfunction or missing part, do not install this device and return it to its seller.
It is necessary to treat this product and its parts as electronic waste after its lifetime is terminated. Before
starting installation, make sure that all wires, connected parts or terminals are de-energized. While mounting
and servicing observe safety regulations, norms, directives and professional, and export regulations for working
with electrical devices. Do not touch parts of the device that are energized – life threat. Due to transmissivity
of RF signal, observe correct location of RF components in a building where the installation is taking place. RF
Control is designated only for mounting in interiors. Devices are not designated for installation into exteriors
and humid spaces. The must not be installed into metal switchboards and into plastic switchboards with metal
door – transmissivity of RF signal is then impossible. RF Control is not recommended for pulleys etc. – radio-
frequency signal can be shielded by an obstruction, interfered, battery of the transceiver can get flat etc. and
thus disable remote control.
Warning
Designed & manufactured by:
ELKO EP, s.r.o. Palackého 493, 769 01 Holešov, Všetuly, Czech republic
www.elkoep.com, Hotline: [phone]