Inficon Micro GC Fusion User manual

1 of 4
Micro GC Fusion
®
Rack Mount Instruction Sheet
INSTRUCTION SHEET
IPN 074-683-P1A
Introduction
This document indicates the necessary materials and proper procedure when installing
the 4-module Micro GC Fusion into a rack.
NOTE: The Rack Mount Kit (952-4100-G1) is intended for the 4-module
Micro GC Fusion chassis only.
Rack Mount Kit (952-4100-G1)
PN Description Quantity
952-4005-P2 . . . Bracket-Rack Mount, Right. . . . . . . . . . . . . . . . . . . . . . . . . . . 1
952-4006-P2 . . . Bracket-Rack Mount, Left . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
070-2026 . . . . . . Handle 6.375 LG 2-leg 10-32 THD SS ROHS . . . . . . . . . . . . 2
090-076 . . . . . . . Screw 10-32 x 0.500 LG Button SOC HD SS . . . . . . . . . . . . . 4
070-2028 . . . . . . Washer, Countersink #10 hole 0.593 OD SS . . . . . . . . . . . . . 8
070-2027 . . . . . . Nut, Retainer G-Type 10-32 THD Steel/ZN RoHS . . . . . . . . . 8
090-062 . . . . . . . Screw, 10-32 x 0.375 Lg Phil Flat Head SS . . . . . . . . . . . . . . 6
090-077 . . . . . . . Screw, 10-32 x 0.750 Lg Phil Oval Head SS . . . . . . . . . . . . . 8
NOTE: PN 070-2026 and 090-076 are preassembled on PN 952-4005-P2 and
952-4006-P2 at the factory.
Required Tools
Phillips-head screw driver
3 mm hex driver
Installing the Rack Mount Kit
1Ensure the instrument is powered down and all connections are removed (including
power supply, Ethernet cable and carrier gas lines).
2Remove the rubber feet from the bottom of Micro GC Fusion by removing the hex
screw located at the center of the foot. (See Figure 1.)
NOTE: If needed, properly store the rubber feet and screws for future
bench top installation.
Figure 1 Remove rubber feet from Micro GC Fusion

2 of 4
IPN 074-683-P1A
Micro GC Fusion Rack Mount Instruction Sheet
3Install brackets (PN 952-4005-P2 and 952-4006-P2) onto the 19 in. rack prior to
attaching Micro GC Fusion when access is available below. Rack mount brackets
shall be installed onto the unit prior to rack installation if underside access is not
available.
3a Attach four retainer nuts to the left bracket (952-4006-P2) in the four hole
locations. (See Figure 2.)
Figure 2 Attach retainer nuts
3b Place the left bracket (PN 952-4006-P2) on the rack, as shown in Figure 3 and
line up the holes with the retainer nuts.
Figure 3 Line up the bracket with the retainer nuts

3 of 4
IPN 074-683-P1A
Micro GC Fusion Rack Mount Instruction Sheet
3c Thread the oval head screw (PN 090-077) through washer (PN 070-2028) as
shown in Figure 4, then screw the bracket into the retainer nut.
Figure 4 Screw bracket into retainer nut
3d Repeat step 3c to finish securing the remaining retainer nuts on the left bracket.
3e To attach the right bracket (PN 952-4005-P2), repeat steps 3a through 3d.
4Once both brackets are secure, gently place Micro GC Fusion onto the rack mount
brackets. (See Figure 5.)
Figure 5 Micro GC Fusion set on mounting brackets
5Line up the holes on the bottom of the unit to the holes in the brackets. (See Figure 6.)
Figure 6 Align unit with bracket holes

www.inficon.com [email protected]
Due to our continuing program of product improvements, specifications are subject to change without notice.
All trademarks are the property of their respective owners.
4 of 4
IPN 074-683-P1A ©2017 INFICON
Micro GC Fusion Rack Mount Instruction Sheet
6Secure the instrument on the brackets with the provided flat Phillips-head screws
(PN 090-062). (See Figure 7.)
Figure 7 Use screws to attach unit to brackets
7Micro GC Fusion is now attached to the rack. (See Figure 8.)
Figure 8 Rack mounted Micro GC Fusion