Infineon AIROC CYW20829 User manual

Application note
Please read the sections “Important notice” and “Warnings” at the end of this document
002-38518 Rev. **
www.infineon.com
2023-09-12
r e s t r i c t e d
AN238518
Achieving long range transmission using
AIROC™ CYW20829 Bluetooth® LE SoC
About this document
Scope and purpose
This application note explains the detailed test setup for long range transmission using the AIROC™ CYW20829
Bluetooth® LE SoC. The firmware used in this application is provided as a code example with the
ModusToolbox™software development kit.
Intended audience
This application note is intended for those who wants to integrate the Bluetooth® LE long range feature on
CYW20829.

Application note
2
002-38518 Rev. **
2023-09-12
r e s t r i c t e d
Achieving long range transmission using AIROC™ CYW20829 Bluetooth® LE
SoC
Table of contents
Table of contents
About this document....................................................................................................................... 1
Table of contents............................................................................................................................ 2
1Introduction .......................................................................................................................... 3
1.1 AIROC™ CYW20829 Bluetooth LE SoC.....................................................................................................3
2Long Range Application .......................................................................................................... 4
2.1 Bluetooth Spec for PHY...........................................................................................................................5
2.2 LE Coded PHY Implementation...............................................................................................................6
2.3 LE Coded PHY Packet Format .................................................................................................................6
3Hardware Setup..................................................................................................................... 7
3.1 CYW20829 Evaluation Board...................................................................................................................7
3.2 LE-LR Test Setup......................................................................................................................................8
3.2.1 External Antenna................................................................................................................................9
3.2.2 User Buttons.......................................................................................................................................9
3.2.3 Display Shield.....................................................................................................................................9
4Software and Tools................................................................................................................10
4.1 ModusToolbox.......................................................................................................................................10
4.2 Code Examples......................................................................................................................................10
4.3 LE LR Central Applicatioin.....................................................................................................................10
4.4 LE LR Peripheral Applicatioin................................................................................................................11
4.5 Build and Flash the Firmware...............................................................................................................11
5Testing and Results ...............................................................................................................12
5.1 Test Procedure ......................................................................................................................................12
5.2 Noise Interference.................................................................................................................................13
5.3 Antenna Orientation..............................................................................................................................13
5.4 Antenna Radiation.................................................................................................................................14
5.5 Power Estimation..................................................................................................................................14
5.6 Range vs RSSI Value ..............................................................................................................................16
5.7 Bluetooth Range Estimator...................................................................................................................16
References....................................................................................................................................17
Revision history.............................................................................................................................18
Disclaimer.....................................................................................................................................19

Application note
3
002-38518 Rev. **
2023-09-12
r e s t r i c t e d
Achieving long range transmission using AIROC™ CYW20829
Bluetooth® LE SoC
Introduction
1Introduction
The AIROC™CYW20829 has best-in-class RF link budget with an integrated power amplifier providing
10 dBm of transmit output power and receive sensitivity of -98 dBm for LE 1 Mbps and -106 dBm for LE long
range 125 Kbps. The long range claims up to 2.3 KM.
1.1 AIROC™ CYW20829 Bluetooth® LE SoC
CYW20829 is a dual-core Arm® M33 device where one M33 core reserved as a Bluetooth® controller, and the
other M33 core for customer applications. The CPU subsystem provides 256-KB RAM, XIP interface for external
flash, and a rich set of peripherals to enable a diverse set of applications.
The AIROC™CYW20829 is supported by the ModusToolbox™ development environment, which enables
developers to accelerate time-to-market for Bluetooth®-enabled IoT solutions.

Application note
4
002-38518 Rev. **
2023-09-12
r e s t r i c t e d
Achieving long range transmission using AIROC™ CYW20829
Bluetooth® LE SoC
Long range application
2Long range application
Figure 1 illustrates the block diagram of the long-range application using the CYW20829 Bluetooth® LE SoC. The
application includes a combination of peripheral and central devices. The LE long-range peripheral configures
the device as Bluetooth® LE GATT Server, and the LE long-range central application configures the device as
Bluetooth® LE GATT Client.
CYW20829
External Flash Radio Subsystem
BTSTACK
LE-LR Application
(Central/Client)
Custom
GATT
UART/
I2C/SPI
GPIO
USER
BUTTON DISPLAY
Board
Antena
E1
CYW20829
External FlashRadio Subsystem
BTSTACK
LE-LR Application
(Peripheral/
Server)
Custom
GATT
UART/
I2C/SPI GPIO
USER
BUTTON
DISPLAY
Board
Antena
E1
CYW920829M2EVK-02 CYW920829M2EVK-02
Figure 1 Block diagram
The peripheral device implements a custom GATT Server profile that includes the following services:
•Hello Sensor custom service
•Device Information service
•Battery level service
The Hello Sensor service includes a custom Notify characteristic, which sends a notification or indication to the
peer client device upon connection.
The application uses a UART to send debug messages on a UART terminal emulator. The peripheral device
starts to advertise its presence using LE-LR PHY when a button press is detected. Similarly, central device scans
for the peripheral device upon button press. After an LE connection is established, the central device registers
for notifications by using the CCCD handle of the Notify characteristic. Because the CCCD handle of the Notify
characteristic requires write authentication, an attempt to enable notification/indication triggers the pairing
process at the central side. After the pairing process completes, the peer device's link keys and addresses are
stored in the device's flash memory and, therefore, bonded. The user button on the peripheral board is
configured to trigger an interrupt on the falling edge. When this button is pressed, the device switches the
coding algorithm between S=2 and S=8 and notify using the modified coding algorithm.

Application note
5
002-38518 Rev. **
2023-09-12
r e s t r i c t e d
Achieving long range transmission using AIROC™ CYW20829
Bluetooth® LE SoC
Long range application
2.1 Bluetooth® spec for PHY
The Bluetooth® technology is a full protocol stack. The bottom layer of this stack is called the Physical Layer
and is normally referred to as PHY.
Bluetooth® 5 adds two new PHY variants to the PHY specification, compared to the previous version. Each PHY
variant has its own particular characteristics and is designed with specific objectives. The three PHYs, LE 1M, LE
2M, and LE Coded, are referenced in specifications.
LE 1M is the PHY used in Bluetooth® 4 and earlier versions. It uses Gaussian Frequency Shift Keying (GFSK) and
has a symbol rate of 1 Msps. Higher up the stack, this correlates to a bit rate of 1 Mbps since one symbol
corresponds to one data bit. LE 1M continues to be available for use in Bluetooth® 5 and in fact, its support is
mandatory.
The new LE 2M PHY allows the physical layer to operate at 2 Msps and thus enables higher data rates than LE
1M. Its support in a Bluetooth® chip is optional.
The LE Coded PHY allows the range to be quadrupled (approximately), compared with Bluetooth® 4, and this is
achieved without increasing the required transmission power.
Physical Layer (PHY)
Link Layer Direct Test Mode
Host Controller Interface
Logical Link Control & Adaption Protocol
Attribute Protocols Security Manager
Generic Attribute Profiles
Generic Access Profiles
Applications
CONTROLLER
HOST
APPS
Figure 2 Bluetooth® architecture diagram

Application note
6
002-38518 Rev. **
2023-09-12
r e s t r i c t e d
Achieving long range transmission using AIROC™ CYW20829
Bluetooth® LE SoC
Long range application
2.2 LE Coded PHY implementation
The LE Coded PHY can be used with two different coding schemes: S=2 and S=8. The Pattern Mapper converts
each bit from the convolutional FEC encoder into P symbols, where the value of P depends on the coding
scheme used. If S=2, there is no change (i.e. P=1). If S=8, each bit from the FEC encoder produces 4 output bits
(i.e. P=4) from the Pattern Mapper. The specifics are described in this section.
The choice of the coding scheme, S=2 or S=8, with the LE Coded PHY has two consequences. When two symbols
represent 1 bit, the PHY data rate is 500 Kbps; for S = 8 (where 8 represents 1 bit), the PHY data rate is 125 Kbps.
Due to the requirement for redundant data to support the FEC algorithm at the receiver end, it also impacts the
number of symbols, which must be transmitted and hence reduces the overall data rate. Specifically, one bit
which passed through both the FEC Encoder and the Pattern Mapper becomes 2 bits when S=2 or 8 bits when
S=8. The following table explains this.
2.3 LE Coded PHY packet format
The packet format defined for the LE Coded PHY is shown in Figure 3.
Preamble Access Address CI TERM1 PDU, N bytes CRC TERM2
FEC block1 FEC block2
S=8 coding S=2 or S=8 coding
Figure 3 Packet format
Each packet consists of the Preamble, FEC block 1, and FEC block 2.
•The Preamble is not coded.
•The FEC block 1 consists of three fields: Access Address, Coding Indicator (CI), and TERM1. CI determines
which coding scheme is used for FEC block 2.
•The FEC block 2 consists of three fields: PDU, CRC, and TERM2. These shall use either the S=2 or S=8 coding
scheme depending on the value of the CI.
The entire packet is transmitted with 1 Msym/s modulation..
Input
Output with S=2
Output with S=8
Data rate
0
0
0011
125 kb/s or 500 kb/s
1
1
1100
125 kb/s or 500 kb/s

Application note
7
002-38518 Rev. **
2023-09-12
r e s t r i c t e d
Achieving long range transmission using AIROC™ CYW20829
Bluetooth® LE SoC
Hardware setup
3Hardware setup
3.1 CYW20829 evaluation board
The CYW20829 M.2 board (CYW920829M2IPA2) consists of the 56-pin silicon target device on a custom pinout
M.2 card that is interfaced with the base board (CYW9BTM2BASE3-01). The CYW20829 silicon pins should be
brought out to the base board through the M.2 connector, featuring the peripherals such as UART, I2C, to be
used with sensors and displays. The board is powered using a USB micro type B cable. Refer to the
CYW920829M2EVK-02 kit user guide for more information.
Figure 4 Evaluation board

Application note
8
002-38518 Rev. **
2023-09-12
r e s t r i c t e d
Achieving long range transmission using AIROC™ CYW20829
Bluetooth® LE SoC
Hardware setup
3.2 LE-LR test setup
Two evaluation boards are used to set up the LE-LR demo. The CYW920829M2EVK-02 board is used with
CYW920829M2IPA1 (M.2 Card), which uses the PCB-based antenna.
CYW920829M2EVK-02 CYW920829M2EVK-02
SERIAL MONITOR
USB Micro B Board Antenna
Peripheral (Server)
Central (Client)
Laptop
Figure 5 Test setup
Figure 5 shows the setup block. Both the evaluation kits are connected to the laptop over a 2-meter long USB
cable. The boards are mounted on the 2-meter long pipe. The boards are powered using the same USB
connector and the serial logs are captured in the laptop with a serial monitor. One board is configured as a
server (peripheral) and the other is configured as a client (central). The optional display shield is used on the
client side to show the connection details and RSSI values on the OLED screen. The user buttons on the EVK are
used to initiate the connection between the two boards. Refer to section 5for the test sequence. Figure 6 shows
the actual setup.
Figure 6 Test setup

Application note
9
002-38518 Rev. **
2023-09-12
r e s t r i c t e d
Achieving long range transmission using AIROC™ CYW20829
Bluetooth® LE SoC
Hardware setup
3.2.1 External antenna
The external antenna is one of the preferred options to use in the long-range application. To use the external
antenna, switch the capacitor (C25) on the CYW920829M2IPA1 (M.2 Card) towards the external antenna path, as
shown in Figure 7.
Figure 7 Antenna switching
3.2.2 User buttons
The user button (SW2) on the EVK is used for the following:
•Initiate the advertisement on the server side and initiate the scanning on client side
•Switch the coding scheme between S=2 and S=8 after the connection is established.
Reset button (SW1) is used to re initiate the application on central & peripheral side.
3.2.3 Display shield
The display shield is optional and can be used to show the coding scheme, RSSI values, and connection status
etc. The user can enable or disable the display shield in the firmware setting (makefile).

Application note
10
002-38518 Rev. **
2023-09-12
r e s t r i c t e d
Achieving long range transmission using AIROC™ CYW20829
Bluetooth® LE SoC
Software and tools
4Software and tools
This section explains the required software tools to create and build the long-range application for testing.
4.1 ModusToolbox™
ModusToolbox™ software is a modern, extensible development environment supporting a wide range of
Infineon microcontroller devices. It provides a flexible set of tools and a diverse, high-quality collection of
application-focused software. These include configuration tools, low-level drivers, libraries, and operating
system support, most of which are compatible with Linux-, macOS-, and Windows-hosted environments.
Refer to the Eclipse IDE for ModusToolbox™ user guide for more details.
4.2 Code examples
ModusToolbox™ code examples can be found through the GitHub code example page. The following two
example codes are required to run the LE-LR application:
•mtb-example-btstack-freertos-le-lr-central
•mtb-example-btstack-freertos-le-lr-peripheral
Import these examples using the Project Creator tool, as shown in Figure 8, to create an application and use it
directly with ModusToolbox™ tools.
Figure 8 Importing examples
4.3 LE LR central application
This is a GATT client application designed to connect and access the services of the server device (Hello Sensor)
using the LE-LR PHY. This application has the following features:
•LE Stack registration for various events
•Connecting to the peripheral
•Processing the notification from the server.
•Scan and connect to the peer over the LE Coded PHY
•Switch between S=2/S=8 PHY coding algorithms

Application note
11
002-38518 Rev. **
2023-09-12
r e s t r i c t e d
Achieving long range transmission using AIROC™ CYW20829
Bluetooth® LE SoC
Software and tools
For more details, refer to the central application’s README.md.
4.4 LE LR peripheral application
This is a GATT server application designed to obtain the sensor data (simulated) and connect to the client
application using the LE-LR PHY.
•LE Stack registration for various events
•Connecting to the client
•Sending the notification data.
•Connect over LE Coded PHY
For more details, refer to the peripheral application’s README.md.
4.5 Build and flash the firmware
The LE-LR application can be built within ModusToolbox™or the ModusShell cmd line. The binary is generated
in the build folder. The firmware can be loaded into the Eval kits using KitProg3 or using an external SWD with
Cypress Programmer. Refer to the Cypress Programmer user guide for more details.
Figure 9 Console serial output

Application note
12
002-38518 Rev. **
2023-09-12
r e s t r i c t e d
Achieving long range transmission using AIROC™ CYW20829
Bluetooth® LE SoC
Testing and results
5Testing and results
Testing is performed at Newport Beach, CA, to get a clear line of sight, and less environment radio noise.
5.1 Test procedure
1. Connect the board to the laptop and download the firmware
2. Press SW1 (Reset) on both the peripheral and central devices to initialize the application
3. Wait for some time for the applications to start and print log messages on the console.
4. Press SW2 on the peripheral device to start the advertisement
5. Press SW2 on the client device to start discovering the server and connects to it
6. Once the connection is established, the logs start printing RSSI values and time counter values. If the
display is used, the details are showed on the display as well.
7. Take any one board to move far away; the distance is calculated to be around 2.3 KM
8. If there is a disconnection in between, the client tries to re-establish the connection with server.
Figure 10 Distance range in Google map
LE-LR Path
2.29KM

Application note
13
002-38518 Rev. **
2023-09-12
r e s t r i c t e d
Achieving long range transmission using AIROC™ CYW20829
Bluetooth® LE SoC
Testing and results
5.2 Noise interference
Noise and interference are the largest contributors to poor range in a long-range testing environment. In the
real world, increased noise means your Bluetooth® devices may disconnect at ranges far shorter than
advertised. To improve SNR, it is important to reduce the noise and interference during testing. To reduce
interference, make sure to test in the morning and walk away from people to reduce the impact of noise.
Maintain a line of sight, or LoS, connection between the peripheral and central devices at all times.
People often carry multiple devices that operate on the 2.4-GHz band, such as their smartphones,
smartwatches, and wireless earbuds. Just as a building’s walls may inhibit Bluetooth® range, other physical
objects, such as beach umbrellas or lifeguard towers, also contribute to multipath, and may absorb radio
frequency energy. Multipath occurs when radio signals propagate between two antennas via multiplate paths.
Multipath is undesirable, as it can lead to interference and distortion of a wanted signal. In the real world, LoS
between devices may not be plausible. We actively monitored the Received Signal Strength Indicator (RSSI), of
the receiver and adjusted the walking path along the beach during testing to keep the RSSI higher than the
maximum S8 Coded PHY sensitivity. The maximum output power of the CYW20829 MCU is 10 dBm using the
internal power amplifier, and the Coded PHY helps to improve the maximum sensitivity of to -106 dBm. The
Link budget is the sum of the absolute value of all gains and losses of a radio frequency system in decibels. In
an ideal environment, the maximum link budget is |10 dBm| output power + |-106 dBm| sensitivity = 116 dB.
5.3 Antenna orientation
Antenna directivity is a measure of the amount of radiated energy moving in a particular direction, while
antenna gain takes both an antenna’s directivity and efficiency. Antennas do not radiate with the same power
in all directions, as shown in Figure 11. To determine the directions in which the kit radiates the strongest, the
antenna gain of the CYW920829M2EVK-02 kit is measured.. Different Bluetooth® antenna radiate most optimally
in different directions, which influence the directions in which the boards face during testing. Since the
directivity of an antenna when transmitting is identical to the directivity of an antenna when receiving, both the
boards were placed facing each other, taking into consideration the maximum antenna gain (see Figure 6). The
CYW920829M2EVK-02 kit is considered a “directional” antenna, as the radiation pattern is strongest in one
particular angular direction.
Figure 11 Board antenna orientation

Application note
14
002-38518 Rev. **
2023-09-12
r e s t r i c t e d
Achieving long range transmission using AIROC™ CYW20829
Bluetooth® LE SoC
Testing and results
5.4 Antenna radiation
The antenna radiation is tested across different frequencies. Figure 12 shows the radiation pattern for
difference frequencies with maximum antenna gain orientation.
Figure 12 Board antenna radiation
5.5 Power estimation
The power consumption for the LE-LR application is calculated during the connected state between the central
and peripheral devices. Figure 13 shows the current measurements for 1-minute duration.
Figure 13 Current measurement

Application note
15
002-38518 Rev. **
2023-09-12
r e s t r i c t e d
Achieving long range transmission using AIROC™ CYW20829
Bluetooth® LE SoC
Testing and results
The current measurement is performed at different ranges and the values are shown in the following table:
Device mode
VPA Avg. current
VBAT Avg. current
VDDIO Avg.
current
Total current
RSSI
Peripheral
3.72 mA
227.68 µA
41.446 µA
3.989 mA
-55 dBm
Central
250.27 µA
111.68 µA
2.671 µA
362 µA
-55 dBm

Application note
16
002-38518 Rev. **
2023-09-12
r e s t r i c t e d
Achieving long range transmission using AIROC™ CYW20829
Bluetooth® LE SoC
Testing and results
5.6 Range vs RSSI value
The RSSI values are captured at every second along with transmission data. The distance versus the RSSI values
are plotted in Figure 14 (the distance values in the horizontal axis are in meters).
Figure 14 Range vs RSSI
5.7 Bluetooth® range estimator
The Bluetooth® range estimator tool from Bluetooth® SIG used to estimate the range of Bluetooth® with
parameters.
0
51.4
258.4
528.1
817.3
1141
1463
1699
1925
0 500 1000 1500 2000 2500
-45
-65
-86
-88
-90
-92
-94
-101
-107
Range vs RSSI

Application note
17
002-38518 Rev. **
2023-09-12
r e s t r i c t e d
Achieving long range transmission using AIROC™ CYW20829
Bluetooth® LE SoC
References
References
[1] GitHub code examples for ModusToolbox ™ software
[2] AIROC™ CYW20829 Datasheet
[3] ModusToolbox™software
[4] Bluetooth® Sig Spec

Application note
18
002-38518 Rev. **
2023-09-12
r e s t r i c t e d
Achieving long range transmission using AIROC™ CYW20829
Bluetooth® LE SoC
Revision history
Revision history
Document revision
Date
Description of changes
**
2023-09-12
Initial version

Important notice
Warnings
Edition 2023-09-12
Published by
Infineon Technologies AG
81726 Munich, Germany
© 2023 Infineon Technologies AG.
All Rights Reserved.
Do you have a question about this
document?
Email: [e-mail]
Document reference
002-38518 Rev. **
The information contained in this application note
is given as a hint for the implementation of the
product only and shall in no event be regarded as a
description or warranty of a certain functionality,
condition or quality of the product. Before
implementation of the product, the recipient of this
application note must verify any function and other
technical information given herein in the real
application. Infineon Technologies hereby
disclaims any and all warranties and liabilities of
any kind (including without limitation warranties of
non-infringement of intellectual property rights of
any third party) with respect to any and all
information given in this application note.
The data contained in this document is exclusively
intended for technically trained staff. It is the
responsibility of customer’s technical departments
to evaluate the suitability of the product for the
intended application and the completeness of the
product information given in this document with
respect to such application.
Due to technical requirements products may contain
dangerous substances. For information on the types
in question please contact your nearest Infineon
Technologies office.
Except as otherwise explicitly approved by Infineon
Technologies in a written document signed by
authorized representatives of Infineon Technologies,
Infineon Technologies’ products may not be used in
any applications where a failure of the product or any
consequences of the use thereof can reasonably be
expected to result in personal injury.
Trademarks
All referenced product or service names and trademarks are the property of their respective owners.
Disclaimer