Infineon PSoC 4100S Max pioneer kit User manual

www.cypress.com/CY8CKIT-041S-MAX
Quick start guide
PSoC™ 4100S Max pioneer kit
CY8CKIT-041S-MAX
Kit contents
1. PSoC™ 4100S Max pioneer board
2. Capacitive sensing expansion board
3. USB Type-A to Micro-B cable
4. Six jumper wires (five inches each)
5. 40-pin FFC cable (two inches)
6. Quick start guide (this document)

Quick start guide
PSoC™ 4100S Max pioneer board
connected to PC
Before you start
1. Ensure that jumper J10 is in 5V
position and that jumper J11 is
populated.
2. Connect the board to your PC
using the provided USB cable.
3. Observe that the Power LED and
KitProg3 status LED turn ON.
Note: This demo does not require
driver installation, but driver
installation may occur in the
background.
Finger touch on the CAPSENSE™ button
Test the basic operation
1. Press the XRES switch (SW1) to
reset the device.
2. Touch a CAPSENSE™ button.
Observe that the corresponding
LED turns ON.
3. Remove the finger from the
button. Observe that the LED
turns OFF.
4. To evaluate additional features
of this kit, see the code example,
CE231079 – PSoC™ 4: MSC
CAPSENSE™ CSX button tuning.
See the PSoC™ 4100S Max
pioneer kit guide for more code
examples.

Quick start guide
PSoC™ 4100S Max pioneer board details
1 Power LED (D2)
2 KitProg3 USB connector (J8)
3 KitProg3 status LED (D3)
4 PSoC™ 5LP-based KitProg3 programmer
and debugger (CY8C5868LTI-LP039, U2)
5 KitProg3 programming mode
selection button (SW3)
6 Voltage regulator (U3)
7 Power selection jumper (J10)
8 PSoC™ 4100S Max MCU current
measurement header (J11)
9 Reset button (SW1)
10 Arduino UNO R3-compatible
power header (J1)
11 PSoC™ 4100S Max MCU 10-pin SWD
program and debug header (J12)
12 Arduino UNO R3-compatible I/O
headers (J2, J3, J4)
13 User button (SW2)
14 CAPSENSE™ buttons (CSB1, CSB2)
15 User LEDs (D1, D4, D5)
16 40-pin FFC connector for capacitive
sensing expansion board (J9)
17 Thermistor (TH1)
18 PSoC™ 4100S Max MCU
(CY8C4149AZI-S598, U1)
19 PSoC™ 4100S Max MCU extended I/O
header (J6)*
20 External power supply connector (J5)*
* Not populated; footprint only
1
2
3
4
5
7
8
9 10
6
11 12 13 14
15
16
17
18151920 12

NC/NC
VTRAG/I0REF
XRES/RESET
V3_3/V3_3
V5_0/5V
GND/GND
GND/GND
VIN/VIN
P6_3/D7
P6_2/D6
P6_1/D5
P6_0/D4
P8_3/D3
P8_2/D2
P8_1/D1
P8_0/D0
P1_0/SCL
P1_1/SDA
VREF/AREF
GND/GND
P10_2/D13
P10_1/D12
P10_0/D11
P10_3/D10
P10_5/D9
P10_4/D8
P4_2
P4_3
P5_1
P5_2
P6_4*
P12_0*
P7_3*
P7_4*
P0_6*
P0_7*
P2_0/A0
P2_1/A1
P2_2/A2
P2_3/A3
P2_4/A4
P2_5/A5
P2_6*
P2_7
P1_2
P1_3
P1_4
P1_5
P1_6
P7_2
P7_5
P12_1
Arduino Uno R3 I/Os
LEGEND
PSoC™ 4100S Max I/Os
Note: *Not connected
Quick start guide
For the latest information about this kit, visit www.cypress.com/CY8CKIT-041S-MAX
PSoC™ 4100S Max pioneer board pinout details
Date: 06/2021 All rights reserved. ©2021 Infineon Technologies AG
Document number: 002-31573 Rev. *B