Infineon TC2X5 User manual

User’s Manual
V 2.0 2013-05
Microcontrollers
32-Bit
Microcontroller
Application Kit TC2X5
Hardware: APPLICATION KIT TC2X5 V2.0
Hardware Manual
Downloaded by [email protected] 09/08/2019 14:06:40

Edition 2013-05
Published by
Infineon Technologies AG
81726 Munich, Germany
©2013 Infineon Technologies AG
All Rights Reserved.
Legal Disclaimer
The information given in this document shall in no event be regarded as a guarantee of conditions or
characteristics. With respect to any examples or hints given herein, any typical values stated herein and/or any
information regarding the application of the device, Infineon Technologies hereby disclaims any and all warranties
and liabilities of any kind, including without limitation, warranties of non-infringement of intellectual property rights
of any third party.
Information
For further information on technology, delivery terms and conditions and prices, please contact the nearest
Infineon Technologies Office (www.infineon.com).
Warnings
Due to technical requirements, components may contain dangerous substances. For information on the types in
question, please contact the nearest Infineon Technologies Office.
Infineon Technologies components may be used in life-support devices or systems only with the express written
approvalofInfineonTechnologies,ifafailureofsuchcomponentscanreasonablybeexpectedtocausethe failure
of that life-support device or system or to affect the safety or effectiveness of that device or system. Life support
devices or systems are intended to be implanted in the human body or to support and/or maintain and sustain
and/or protect human life. If they fail, it is reasonable to assume that the health of the user or other persons may
be endangered.
Downloaded by [email protected] 09/08/2019 14:06:40

User’s Manual
V 2.0 2013-05
Microcontrollers
32-Bit
Microcontroller
Application Kit TC2X5
Hardware: APPLICATION KIT TC2X5 V2.0
Hardware Manual
Downloaded by [email protected] 09/08/2019 14:06:40

Application Kit TC2X5
Hardware Manual
User’s Manual V 2.0, 2013-05
Trademarks
TriCore®is a trademark of Infineon Technologies AG.
Application Kit TC2X5 User’s Manual
Revision History: V 2.0 2013-05
Previous Versions: 1.0
Page Subjects (major changes since last revision)
all adapt to hardware version V2.0
–
–
We Listen to Your Comments
Any information within this document that you feel is wrong, unclear or missing at all?
Your feedback will help us to continuously improve the quality of this document.
Please send your proposal (including a reference to this document) to:
[email protected]
Downloaded by [email protected] 09/08/2019 14:06:40

User’s Manual L-1 V 2.0, 2013-05
Application Kit TC2X5
Hardware Manual
1Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
2 Application Kit Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
2.1 Summary of Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
2.2 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
2.3 Placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4
3 Application Kit Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
3.1 Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
3.1.1 Power via supply connector (X101) . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
3.1.2 Shutdown the board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
3.2 Real Time Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
3.3 XGA Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
3.3.1 Write a display register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
3.3.2 Read a display register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
3.3.3 Touch controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
3.4 Micro SD card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
3.5 LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
3.6 Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
3.7 USB Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
3.7.1 Serial Connection to PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
3.7.2 miniWiggler JDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
3.8 Beeper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
3.9 MultiCAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
3.10 LIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
3.11 Ethernet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
3.12 Other peripherals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
3.13 Toggle LED’s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
3.14 Debug System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
3.14.1 OCDS1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
4 Signal Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
5 Connector Pin Assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
5.1 IO Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
5.2 Power connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
5.3 USB connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
5.4 CAN connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
5.5 LIN connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3
5.6 OCDS connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3
5.7 Ethernet Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4
5.8 DAP connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4
Table of Contents
Downloaded by [email protected] 09/08/2019 14:06:40

User’s Manual L-2 V 2.0, 2013-05
Application Kit TC2X5
Hardware Manual
6 Schematic and Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
6.1 Schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
6.2 Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-6
6.3 Layout with Dimensioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-8
Downloaded by [email protected] 09/08/2019 14:06:40

User’s Manual L-3 V 2.0, 2013-05
Application Kit TC2X5
Hardware Manual
Figure 2-1 Application Kit TC2X5 Block Schematic . . . . . . . . . . . . . . . . . . . . . . 2-3
Figure 2-2 Applcation Kit TC2X5 V2.0 Top Placement . . . . . . . . . . . . . . . . . . . . 2-4
Figure 2-3 Applcation Kit TC2X5 V2.0 Bottom Placement . . . . . . . . . . . . . . . . . 2-5
Figure 5-1 IO Connectors - Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
Figure 5-2 Power connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
Figure 5-3 USB connector Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
Figure 5-4 CAN connector pinout (IDC10) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
Figure 5-5 LIN connector pinout (IDC10) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3
Figure 5-6 OCDS connector pinout (IDC16) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3
Figure 5-7 Ethernet connector pinout (RJ45) . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4
Figure 5-8 DAP connector pinout (FTSH10). . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4
Figure 6-1 Schematic - Project . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2
Figure 6-2 Schematic - CPU and Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . 6-3
Figure 6-3 Schematic - Peripherals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4
Figure 6-4 Schematic - miniWiggler JDS and OCDS1 . . . . . . . . . . . . . . . . . . . . 6-5
Figure 6-5 Component Plot Top Layer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-6
Figure 6-6 Component Plot Bottom Layer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7
Figure 6-7 Dimensioning (mm) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-8
Figure 6-8 Dimensioning (mil) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-9
List of Figures
Downloaded by [email protected] 09/08/2019 14:06:40

User’s Manual L-4 V 2.0, 2013-05
Application Kit TC2X5
Hardware Manual
Downloaded by [email protected] 09/08/2019 14:06:40

User’s Manual L-5 V 2.0, 2013-05
Application Kit TC2X5
Hardware Manual
Table 4-1 Power Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
Table 4-2 Reset Signals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
Table 4-3 Interrupt Signals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
Table 4-4 Clock Signals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
Table 4-5 Debug Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
Table 4-6 Peripheral Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
List of Tables
Downloaded by [email protected] 09/08/2019 14:06:40

User’s Manual L-6 V 2.0, 2013-05
Application Kit TC2X5
Hardware Manual
Downloaded by [email protected] 09/08/2019 14:06:40

Application Kit TC2X5
Hardware Manual
User’s Manual -7 V 2.0, 2013-05
Downloaded by [email protected] 09/08/2019 14:06:40

Application Kit TC2X5
Hardware Manual
Introduction
User’s Manual 1-1 V 2.0, 2013-05
1 Introduction
We congratulate you on your purchase of the TriCore Evaluation Board. This kit is a
versatile tool, providing quick access to the capabilities of TriCore's powerful
architecture.
Applications can be developed easily. The Application Kit is equipped with a variety of
peripherals for connection to the environment. There is also an interface for the On Chip
Debugging Features.
The Application Kit allows easily the development of TriCore applications with the
corresponding tools.
Subsequently, the applications can be downloaded and can be tested with the powerful
debugger software.
This Application Kit Hardware Manual familiarizes you with the TriCore Evaluation Board
and guides you through the initial configuration of the Application Kit.
For detailed technical information about the TC2X5 (e.g. TC275, TC265, TC2D5) please
refer to the User Manual of the device.
Downloaded by [email protected] 09/08/2019 14:06:40

Application Kit TC2X5
Hardware Manual
Introduction
User’s Manual 1-2 V 2.0, 2013-05
Downloaded by [email protected] 09/08/2019 14:06:40

Application Kit TC2X5
Hardware Manual
Application Kit Features
User’s Manual 2-1 V 2.0, 2013-05
2 Application Kit Features
2.1 Summary of Features
– Infineon’s TC2X5 (e.g. TC275, TC265) Controller in LQFP-176 Package
– LCD XGA Display 320x240
– SD card slot (mini SD)
– High Speed CAN Transceivers
– USB to UART bridge
– Ethernet Gigabit PHY
– LIN Transceiver
– Crystal 20MHz (default) or External Clock
– USB miniWiggler JDS for easy debugging
– 4Low Power Status LEDs
– RTC with alarm
– Acoustic beeper
– 100mm x 100mm
Connectors
The Application Kit TC2X5 Toffers a wide variety of connectors:
– Standard power connector
– Micro USB connector for ASC Interface (ASC0) and miniWiggler
– RJ45 connector for Ethernet
– 16-pin header for JTAG interface (OCDS)
– 10-pin header for DAP (optional)
– 10pin (2x5) Header for LIN Transceiver (LIN)
– 10pin (2x5) Header for CAN High Speed Transceiver (CAN0)
– two 40-pin connectors with I/O signals
– mini SD card slot
Components
– Infineon’s Next generation micro controller supply TLE 7368-3E
– LED to validate power supply (5Volt)
– LED indicating RESET (ESR0) active state
– LED indicating activ miniWiggler JDS
– LED switched via DAS software
– Infineon’s High Speed CAN-Transceiver TLE 6250 G
– Infineon’s LIN-Transceiver TLE 7259-2GE
– I2C™ Real-Time Clock/Calendar with SRAM MCP7940M
– USB to UART bridge FT2232HL (FTDI)
– Single Port Gigabit Ethernet PHY PEF7071 (LANTIQ)
Downloaded by [email protected] 09/08/2019 14:06:40

Application Kit TC2X5
Hardware Manual
Application Kit Features
User’s Manual 2-2 V 2.0, 2013-05
– Touch screen controller ADS7843
– 4 general purpose LEDs
– Reset switch
– Start switch
– Xilinx CPLD XC9572XL
Downloaded by [email protected] 09/08/2019 14:06:40

Application Kit TC2X5
Hardware Manual
Application Kit Features
User’s Manual 2-3 V 2.0, 2013-05
2.2 Block Diagram
Figure 2-1 Application Kit TC2X5 Block Schematic
Micro
USB miniWiggler
OCDS1
USB
XTAL
CAN
Transceiver
TxCAN0
RxCAN0 TC2X5
(e.g.
TC275,
TC265)
TriCore
CPU
PLL
CAN0
TX0
RX0
4 LED’s
(P33.8 up to P33.11)
POWER SUPPLY WITH
SUPERSONIC TLE7368-3E
RMII PHY Twisted Pair RJ45
LIN
LIN
Transceiver
TX1
RX1
Micro
SD Card
QSPI0 Serial to
Parallel
converter
XGA Display
320x240
with touch
QSPI1
Acoustic
Beeper
P33.0
RTC
I2C0
ESR1
WAKEUP START
SHUTDOWN
P10.8
Downloaded by [email protected] 09/08/2019 14:06:40

Application Kit TC2X5
Hardware Manual
Application Kit Features
User’s Manual 2-4 V 2.0, 2013-05
2.3 Placement
Figure 2-2 Applcation Kit TC2X5 V2.0 Top Placement
1
1
APPLICATION KIT TC2X5 V2.0
CAN0
POWER
+5,5V...+40V
1
1
L1
RUN
ETH
LIN
ACT
JTAG
1
1
INFINEON TECHNOLOGIES AG
USB
SDCARD
X202
F
X205
X103
X102
X101
U102
U101
+
LS101
L102
X301
X201
U301
D302
BU301
D301
U203
X203
F
X204
U201
BT101
Downloaded by [email protected] 09/08/2019 14:06:40

Application Kit TC2X5
Hardware Manual
Application Kit Features
User’s Manual 2-5 V 2.0, 2013-05
Figure 2-3 Applcation Kit TC2X5 V2.0 Bottom Placement
L4
START
+5V
/PORST
P33.11
P33.8
P33.9
P33.10
ESR0
1
LCD201
S102
S101
D110 D109 D108 D107
D106
D105
Downloaded by [email protected] 09/08/2019 14:06:40

Application Kit TC2X5
Hardware Manual
Application Kit Features
User’s Manual 2-6 V 2.0, 2013-05
Downloaded by [email protected] 09/08/2019 14:06:40

Application Kit TC2X5
Hardware Manual
Application Kit Information
User’s Manual 3-1 V 2.0, 2013-05
3 Application Kit Information
3.1 Power Supply
The microcontroller needs 3 different supply voltages. This voltages are generated
internally via Infineons Next generation microcontroller supply TLE 7368-3E (+5V;
+3,3V) and via the microcontroller itself (+1,3V).
Applying a stable supply voltage causes the power on reset after a short period. The
LED' (+5V) indicate the status of the 5V voltage.
A manual power on reset is executed by pressing the reset button.
NOTE: TO POWER UP THE BOARD YOU MUST
PRESS SHORT THE START BUTTON.
3.1.1 Power via supply connector (X101)
The Board has to be connected to a +5,5V to +40V DC power supply.
The power consumption is not specified yet but a supply with 6V and 600mA should be
sufficient. The pinout for the supply connector is shown in Figure 5-2. There can be used
any standard power pack with a connector where the positive line is surrounded by the
ground line.
3.1.2 Shutdown the board
The board can be switched off by disconnecting the power plug or by software via pin
P10.8. A low level on pin P10,8 will switch off the power regulator except the standby
supply of 2,6V. In this case all only the RTC is working and can wake up the board by an
alarm. In this case you shouldn’t remove the power connector. Make sure that there is
not active alarm from the RTC when you need to switch off the board. In case of an active
alarm the board is not switched off.
3.2 Real Time Clock
The board is equipped with a RTC MCP7940M from Microchip. The device is powered
from the standby voltage of the TLE7368 and is also powered when the TLE7368 is
switched off. For backup when the TLE7368 is not powered then there is a small battery
to hold the value inside the RTC. When the battery is not installed (e.g. first time use)
you could insert the battery in the holder to keep the time. The RTC is connected to the
microcontroller via I2C bus and can trigger an ESR1 interrupt (activ high) with the
alarms. Also an alarm from the RTC will wake-up (switch on) the board if the board is
powered and not started (shutdown). For more information about the RTC please see
the datasheet of MCP7940M.
Downloaded by [email protected] 09/08/2019 14:06:40