INFINITY3DP NEW X1 User manual

4. Avoiding vibrate the build plate and fan by improper operation as to prevent any damages.
2. NEW X1 is designed to work properly at an ambient temperature of between 15°C (59°F) and 32°C (89.6°F) and humidity of between 20% and 50%;
1. Keep the NEW X1 in a clean, dust-free and dry environment that away from fire is essential for proper operation.
5. Leave the machine do certain action automatically should protect the main board caused by reverse current.
3. NEW X1 generates high temperatures as the nozzle can reach up to 300°C (572°F) and the build plate up to 100°C (212°F) that can cause injury.
Never reach inside of the NEW X1 while it is in operation.
6. Remain the structural integrity of the NEW X1 as to ensure the safety and the utility of authorized maintenance.
Operating outside these limits may result in decreased print quality of your models.
C A U T I O N
Failure to read the manual may lead to personal injury, or damage to the INFINITY3DP NEW X1.
This manual describes the application operation of the precision electronic machine.
Please read and understand the user manual carefully.
-1-

TABLE OF CONTENTS
SPECIFICATIONS
DIAGRAM
INSTALLATION
QUICK START
PANEL
Page 3
Page 4
Page 6
Page 8
Page 10
-2-

-3-
Printing
Print Technology
Build Volume
Nozzle Operation Temperature
Build Plate Operation Temperature
Build Plate Leveling
Supplied Software
Connectivity
Power-loss Recovery
Nozzle Diameter
Layer Resolution
Filament Diameter
Supported Filament
Flexible Material
Fused Deposition Modeling (FDM)
210 x 210 x 240 mm (8.26” x 8.26” x 9.45”)
Up to 300°C (572°F)
Up to 100°C (212°F)
Pre-adjusted production (Free Calibration)
Kisslicer (Standard) ※Support - Cura, Simplify3D
SD card slot
Capable
0.4mm
0.02-0.24mm
1.75 mm (0.068”)
PLA/ABS/Nylon/PETG/Carbon/PC/TPE/TPU
Printable (Shore 50A material)
Structure
Extruder Type
Driver
XY Axis
Z Axis
Electronic Control
Fan Cooler
AC Input
Physical Dimensions
Dimensions
Net Weight
Gross Weight
Direct Extruder
Infinity3DP GT80
Caged Ball Linear Guide (Made in Taiwan)
4-Row Ball Bearing Linear Guide
T8 Anti-Backlash Lead Screw (Made in Taiwan)
igus Chainflex® Flexible Cables
Dual / 45mm
100~240AC/320W
W355 x D310 x H474 mm (W13.97”x D12.20” x H18.66”)
11kg / 24.25 Ibs
14 kg / 30.86 Ibs
PANEL

-4-
1. Stepper Motor of X Axis
2. Stepper Motor of Z Axis
3. Handle
4. Filament Rack
5. Limit Switch of X Axis
6. Direct Extruder
13. Control Knob
14. Belt Tensioner of X Axis
15. Power Interface
16. Power Switch
17. Belt Tensioner of Y Axis
18. Limit Switch of Y Axis
7. Heat Bed
8. Stepper Motor of Y Axis
9. Limit Switch of Z Axis
10. USB Interface
11. SD card slot
12. LCD Panel
PANEL

-5-
1. SD Card
2. Build Plate (Glass)
3. Binder Clip
4. Hexagon Screwdriver
5. Cleaning Brush (Steel)
6. Glue Stick
7. Power Cord
8. USB Type B Cable
9. Filament Rack
Included Accessories
PANEL

1. Remove the taps and replace with binder clips in the same indicated place.
※The glass plate, with red tape indicates the place for binder clips, is the print surface for prints.
2. Slightly glue on build plate for aiding in print adhesion.
3. Plug the power cable in the wall socket and connect to the NEW X1.
4. Control > Set Temp > Nozzle / Bed
Place it and wait till the instructed temperature, it’s about to start your print!
※The heating temperature depends on filaments.
PANEL
-6-
STEP 1
GLASS PLATE
Bed :
Nozzle :
Fan Speed (%) :
210
60
0
STEP 4
TEMPERATURE SET TING
STEP 3
POWER ON
BUILD PLATE ADHESION and GLUE STICK
STEP 2

LOADING FILAMENT
1. Place the filament onto the filament rack.(Photo A)
2. Press the feeder button for inserting the filament.(Photo B)
3. Take the end of the filament, insert it into the bottom of the feeder.
Push the filament until it grabbed by the knurled wheel.(Photo C)
4. Gently clean the nozzle by tissue. (Photo D)
5. Press the feeder button to clamp the filament for continue.(Photo E)
-7-
PANEL
※Be aware of the operation is during heating procedure.
STEP 5

STEP 1
CHOOSE A FILE
Main Menu
T-rexbaby-OGT.gcode
moai-new.gcode
circle.gcode
..
STEP 2
START TO PRINT
1. Main Menu > Print From SD >X1_Test > moai-new.gcode
2. NEW X1 will prepare itself by heating up the nozzle and build plate.
While heating up to the instructed temperature, the build plate
would automatically closer to the nozzle as ready to print.
-8-
PANEL

-9-
3. When finished, wait for the build plate to cool down.
※Please be sure to take the build plate out of the machine, so you can grab the object from it.
STEP 3
COMPLETION
PANEL

NEW
moai-new.gcode
TIME: 00:00
SD: 0%
NEW
Z:243.47
HB: 27° N2: X
N1: 26°
Print Speed
Z Axis Height
Heat Bed
Temperature
Fan Speed
Nozzle
Temperature
Print Status
PRINT STATUS
MAIN MENU
Print File
Time
Print Procedure
Main Menu
Control
Set Temp Nozzle
Bed
Fan Speed (%)
Change Filament
Preheat 1
Preheat 2
Cooldown
Disable Steppers
Resume Print
Prepare
Auto Home
Preheat 1 Conf.
Preheat 2 Conf.
About Printer
Printer Info
Printer Status
Print From SD
.gcode
-10-
PANEL
Menu Tree