InHand InGateway502 Instruction manual

Docs » InGateway502 Quick Start Manual
InGateway502 Quick Start Manual
This document is used to explain the basic configuraon operaons of InGateway502 (IG502 for short) networking, soware version update, etc.,
so that users can master the basic configuraon of IG502 and the use of common funcons.
1. Configure IG502 Network Parameters
1.1 Access the IG502
1.2 Connect IG502 to the Internet
2. Update the Soware
2.1 Update the IG502 firmware
2.2 Upgrade the Python SDK of IG502
3. Python Edge Compung
3.1 Install and run Python App
3.2 Update Configuraon File for App
3.3 Update Python App version
3.4 Enable the Debug Mode
4. InHand Cloud
5. Data Collecon And Upload To The Cloud
Appendix
Factory reset
1. Configure IG502 Network Parameters
1.1 Access the IG502

Step 1: By default, the IP address of WAN on IG502 is 192.168.1.1; the IP address of LAN on IG502 is 192.168.2.1. This document uses the
LAN port to access the IG502 as an example. Set the PC’s IP address to be on the same subnet with LAN.
Method 1: Enable the PC to obtain an IP address automacally (recommended)
Method 2: Set a fixed IP address
Select Use the following IP address, enter an IP address (By default,any from 192.168.2.2 to 192.168.2.254), subnet mask (By
default,255.255.255.0), default gateway (By default,192.168.2.1), and DNS server address, and click OK.

Step 2: Launch the browser on the PC and access the IP address of LAN. Enter the login user name and password. The default user name and
password are adm and 123456 respecvely.

Step 3: Aer successful login, you can see the web page as shown below:

Step 4: To change the user name and password for logging in to the web management interface of IG502, choose System > User Management
page of IG502 and set the new user name and password.

Step 5: To change the IP address of LAN, choose Network > Network Interfaces > LAN page of IG502 to configure LAN.

1.2 Connect IG502 to the Internet
Method 1: Connect to the Internet by SIM card
Step 1: Insert the SIM card. (Note: Before inserng or removing the SIM card, unplug the power cable; otherwise, the operaon may cause
data loss or damage the IG502.) Aer inserng the SIM card, connect the 4G LTE antenna to the ANT interface and power on the IG502.

Step 2: Choose Network > Network Interfaces > Cellular page of IG502 and select Enable Cellular and click Submit.

When the network connecon status is Connected and an IP address has been allocated, the IG502 has been connected to the Internet
with the SIM card.

Method 2: Connect to the Internet by Ethernet
Step 1: Use the Ethernet cable to connect the WAN and LAN ports of the IG502 respecvely, as shown below:

Step 2: Choose Network > Network Interface > WAN page of IG502 to configure the IP address of the WAN port and click Submit. (When
the network type is a stac IP address, you need to configure the IP, subnet mask, and other informaon according to the site network
condions.)

Step 3: Choose Network > Roung > Stac Roung page of IG502 to add a stac route for WAN port and click Submit. (Select “WAN” for
the interface item, and configure the other items according to the site network condions.)

Step 4: Choose System > Network Tools page of IG502 and use the Ping tool to check whether the IG502 has successfully connected to
the Internet. The following figure shows that IG502 have successfully connected to the Internet:

2. Update the Software
To obtain the latest soware version of IG502 and updated funcons, contact the customer service center. To update the IG502 soware
version, do as follows.
2.1 Update the IG502 firmware.

Choose System > Firmware Upgrade. Select a firmware file and click Start Upgrading. Aer the update is completed, you are prompted to restart
the system to Apply the new firmware.
2.2 Upgrade the Python SDK of IG502.

Choose Edge Compung > Python Edge Compung. Select Python Engine, select an Python SDK file, and click Upgrade; when the upgrade
confirmaon window pops up, click Confirm. Then the IG502 automacally performs the upgrade.
3. Python Edge Computing
3.1 Install and run Python App

To install and run Python App (App for short) in IG502, please refer to the following process, this document takes Device Supervisor as an
example:
Step 1: Install the App
Before installing the App, you need to ensure that the Python Edge Compung Engine is enabled and the Python SDK is installed, as shown in
the following figure:

Choose Edge Compung > Python Edge Compung. click the Add buon and select the App package file to be installed, then click Confirm.
Aer imporng, you can view the imported Apps, as shown in the following figure:

Step 2: Run the App
Select enable App and click Submit.