InHand InGateway902 User manual

InGateway Documentation
Release 0.0.1
zhangning
Aug 24, 2020

IG902 User manual
1 InGateway Documentation Site Navigation 1
1.1 InGateway902 Quick Start Manual ................................. 1
1.2 InGateway902 User Manual ..................................... 22
1.3 InGateway902 Command Line Instructions ............................119
1.4 InGateway501 Quick Start Manual .................................130
1.5 InGateway501 User Manual .....................................145
1.6 InGateway501 Command Line Instructions ............................189
i

ii

CHAPTER 1
InGateway Documentation Site Navigation
The new IoT edge computing gateway of InHand aims to utilize IoT technologies to support the digital
transformation of industries. The product features powerful edge computing capabilities, to reduce cloud-
end computing resources, and realize data optimization, real-time response, agile connection and model
analysis on the IoT edge, further advancing the development of digital networking in the AI era.
1.1 InGateway902 Quick Start Manual
This document is used to explain the basic conguration operations of InGateway902 (IG902 for short)
networking, software version update, etc., so that users can master the basic conguration of IG902 and the
use of common functions.
•1. Congure IG902 Network Parameters
–1.1 Access the IG902
–1.2 Connect IG902 to the Internet
•2. Update the Software
–2.1 Update the IG902 rmware
–2.2 Upgrade the Python SDK of IG902
–2.3 Upgrade the Docker SDK of IG902
•3. Python Edge Computing
–3.1 Install and run Python App
1

InGateway Documentation, Release 0.0.1
–3.2 Update Conguration File for App
–3.3 Update Python App version
–3.4 Enable the Debug Mode
•4. Device Manager
•Appendix
–Factory reset
1.1.1 1. Congure IG902 Network Parameters
1.1 Access the IG902
• Step 1: By default, the IP address of GE 0/1 on IG902 is 192.168.1.1; the IP address of GE 0/2 on
IG902 is 192.168.2.1. This document uses the GE 0/2 port to access the IG902 as an example. Set the
PC’s IP address to be on the same subnet with GE 0/2.
–Method 1: Enable the PC to obtain an IP address automatically (recommended)
–Method 2: Set a xed IP address
2 Chapter 1. InGateway Documentation Site Navigation

InGateway Documentation, Release 0.0.1
Select Use the following IP address, enter an IP address (By default,any from 192.168.2.2 to
192.168.2.254), subnet mask (By default,255.255.255.0), default gateway (By default,192.168.2.1),
and DNS server address, and click OK.
• Step 2: Launch the browser on the PC and access the IP address of GE 0/2. Enter the login user name
and password. The default user name and password are adm and 123456 respectively.
1.1. InGateway902 Quick Start Manual 3

InGateway Documentation, Release 0.0.1
• Step 3: After successful login, you can see the web page as shown below:
• Step 4: To change the user name and password for logging in to the web management interface of
IG902, choose System > User Management page of IG902 and set the new user name and password.
4 Chapter 1. InGateway Documentation Site Navigation

InGateway Documentation, Release 0.0.1
• Step 5: To change the IP address of GE 0/2, choose Network > Network Interfaces > Ethernet >
Gigabitethernet 0/2 page of IG902 to congure GE 0/2.
1.2 Connect IG902 to the Internet
• Method 1: Connect to the Internet by SIM card
–Step 1: Insert the SIM card. (Note: Before inserting or removing the SIM card, unplug the power
cable; otherwise, the operation may cause data loss or damage the IG902.) After inserting the
SIM card, connect the 4G LTE antenna to the ANT interface and power on the IG902.
1.1. InGateway902 Quick Start Manual 5

InGateway Documentation, Release 0.0.1
–Step 2: Choose Network > Network Interfaces > Cellular page of IG902 and select Enable Cellular
and click Submit.
6 Chapter 1. InGateway Documentation Site Navigation

InGateway Documentation, Release 0.0.1
When the network connection status is Connected and an IP address has been allocated, the
IG902 has been connected to the Internet with the SIM card.
• Method 2: Connect to the Internet by Ethernet
–Step 1: Use the Ethernet cable to connect the GE 0/1 and GE 0/2 ports of the IG902 respectively,
as shown below:
1.1. InGateway902 Quick Start Manual 7

InGateway Documentation, Release 0.0.1
–Step 2: Choose Network > Network Interface > Ethernet > Gigabit Ethernet 0/1 page of IG902
to congure the IP address of the GE 0/1 port and click Submit. (When the network type is a
static IP address, you need to congure the IP, subnet mask, and other information according to
the site network conditions.)
8 Chapter 1. InGateway Documentation Site Navigation

InGateway Documentation, Release 0.0.1
–Step 3: Choose Network > Static Routing > Conguration page of IG902 to add a static route
for GE 0/1 port and click Submit. (Select “Gigabitethernet 0/1”for the interface item, and
congure the other items according to the site network conditions.)
1.1. InGateway902 Quick Start Manual 9

InGateway Documentation, Release 0.0.1
–Step 4: Choose System > Network Tools page of IG902 and use the Ping tool to check whether
the IG902 has successfully connected to the Internet. The following gure shows that IG902 have
successfully connected to the Internet:
1.1.2 2. Update the Software
To obtain the latest software version of IG902 and updated functions, contact the customer service center.
To update the IG902 software version, do as follows.
10 Chapter 1. InGateway Documentation Site Navigation

InGateway Documentation, Release 0.0.1
1.1.3 2.1 Update the IG902 rmware.
Choose System > Firmware Upgrade. Select a rmware le and click Start Upgrading. After the update is
completed, you are prompted to restart the system to Apply the new rmware.
1.1.4 2.2 Upgrade the Python SDK of IG902.
Choose Edge Computing > Python Edge Computing. Select Python Engine, select an Python SDK le, and
click Upgrade; when the upgrade conrmation window pops up, click Conrm. Then the IG902 automatically
performs the upgrade.
1.1. InGateway902 Quick Start Manual 11

InGateway Documentation, Release 0.0.1
1.1.5 2.3 Upgrade the Docker SDK of IG902.
Choose Edge Computing > Docker Manager, close the Docker Manager and import the Docker SDK.
After importing, IG902 will automatically install the Docker SDK. The installation process usually takes 1-2
minutes. Please be patient. After successful installation, select Enable Docker Manager and click Submit.
After enabling the Docker Manager, you can click the access button of the Docker Manager to access the
management page.
12 Chapter 1. InGateway Documentation Site Navigation

InGateway Documentation, Release 0.0.1
Enter the account and password set in the gure above to log in to the Docker Manager.
1.1.6 3. Python Edge Computing
3.1 Install and run Python App
To install and run Python App (App for short) in IG902, please refer to the following process:
• Step 1: Install the App
Before installing the App, you need to ensure that the Python Edge Computing Engine is enabled and
1.1. InGateway902 Quick Start Manual 13

InGateway Documentation, Release 0.0.1
the Python SDK is installed, as shown in the following gure:
Choose Edge Computing > Python Edge Computing. click the Add button and select the App package
le to be installed, then click OK.
After importing, you can view the imported Apps, as shown in the following gure:
14 Chapter 1. InGateway Documentation Site Navigation

InGateway Documentation, Release 0.0.1
• Step 2: Run the App
Select enable App and click Submit.
Once enabled, the App automatically runs and will run every time the IG902 is started.
1.1. InGateway902 Quick Start Manual 15

InGateway Documentation, Release 0.0.1
3.2 Update Conguration File for App
If the installed App supports importing conguration les to modify the running mode, you can update the
App running conguration by referring to the following process:
• Step 1: Choose Edge Computing > Python Edge Computing, click the Import Conguration button
and select the conguration le to be imported, then click Conrm.
• Step 2: Restart the App after the import is successful. After the App restarts, it will runing according
to the imported conguration le.
16 Chapter 1. InGateway Documentation Site Navigation