Innokin itaste mvp 2.0 User manual

WARNING:
1. The iTaste MVP is intended for use by people of legal
age (18+), NOT by non-smokers, children, women
who are pregnant or breaseeding, people with or
at risk of heart disease or people taking medicaon
for depression or asthma. The iTaste MVP is neither
intended for or marketed as a quit smoking aid or
cessaon device.
2. This unit may include small parts, please keep out of
reach of children and pets.
3. Don’t abuse your iTaste MVP even though it’s made
of metal, you may damage it by dropping it.
4.
Don’t aempt to repair the unit by yourself as
damage or personal injury may occur.
5. In order to guarantee the normal funcon of your
iTaste MVP and maintain the effect of vaping, we
suggest that you charge your baeries when they are
below 10% power.
6. In order to prolong the funcon of your iTaste MVP ,
please don’t place it in any environment that is too
hot or too cold too hot or too cold environment.
7. Please obey local laws or regulaons while vaping. If
there are any bans or potenal dangers, please keep
the iTaste MVP off.
8. Your iTaste MVP is not waterproof, please keep it dry.
9. Keep your iTaste MVP from sources of excessive heat.
10.Please don’t drop, throw or abuse your iTaste MVP ,
you may cause damage to outer shell or Inner
components.
11.Innokin is not responsible for baery or charge cable
explosions due to the use of low quality wall charger.
iTaste MVP doesn’t come with any wall charger . We
recommend you use high quality USB wall charger
with 5V 500mA (CE&UL cerfied) . This will takes you
about 2.5h fully charge your iTaste MVP .
12.Use lower waage for low-resistance (ohms)
accessories and higher waage for high-resistance
(ohms) accessories
Warranty
Please consult with Innokin official distributors for their
warranty and return policy. Innokin’s warranty does
not apply to products purchased through third party
vendors.
ITaste MVP is a microprocessor controlled VV/VW
personal vaporizer that lets you easily adjust the
voltage and waage with just a few buon presses.
Specificaons:
Main Features:
Variable Voltage:
voltage can be adjusted from 3.3 – 5.0 volts in .1 volt
increments.
Variable Waage:
Waage can be adjusted from 6.0 – 11.0 W in .5 was
increments.
Ohms meter :
Reads resistance of your atomizer/cartomizer/clearomizer.
MVP 2.0
Operang Voltage : 3.3V-5.0V
Operang Waage : 6.0W-11.0W
Baery capacity : 2600m Ah
Size : 23*41*107mm
Puff counter will record the number of puffs you have
taken. Either press “P “buon or “U” buon 1 second
to check puffs ,The Puff Counter will be cleared when
the device is turned off.
Puff Counter:
Please read the instrucons and precauons before
using the iTaste MVP
If the buon is held down for 10 seconds or longer,
the iTaste MVP will shut itself off unl the buon is
released and pressed again.
The iTaste MVP uses a built in Micro USB Port. You can
recharge it with a Micro USB cable. It can also work as
a pass-through for use while charging.
Remembers last set voltage or waage when the
baery is turned off and then back on.
Digital display shows Ohms meter, Voltage /Waage
seng, number of puffs taken since last me the
baery was turned off.
Short Circuit/Atomizer Protecon protects the iTaste
MVP against shorted atomizers.
The iTaste MVP monitors the baery voltage and will
automacally turn off when the baery is discharged.
The iTaste MVP baery capacity is displayed via
green, yellow and red LED lights.
Green = Fully Charged
Yellow = Half Discharged
Red = In need of charging
iTaste MVP e-cigaree built-in 2600 mAh polymer
Li-Ion rechargeable baery.
Short Circuit/Atomizer Protecon:
Over-Discharge Protecon:
Baery Level Indicator:
Large baery capacity:
High compability 510 connector:
Thread fit iClear10,iClear16 ,iClear30 etc
ON/OFF baery switch:
Quickly clicking“ ”three mes will enable or disable
the baery. Once enabled, holding down the buon
will acvate the baery.
This safety feature prevents the atomizer from
turning on while it's in your pocket or bag and it
prevents any sengs from geng changed without
you knowing.
10 seconds cutoff:
Passthrough:
Remembers last set voltage or waage :
Built-in 3 digit display :
USER MANUAL

Turn ON the small pin switch in boom of iTaste MVP,
connect cable into USB OUTPUT port(DC 5V ,
maximum output current 0.5A ,the 3 most popular
power connectors for iPhone/iPods, MiniUSB
(Motorola/Blackberry), a Micro USB (Motorola/Nokia
/LG/Samsung). Turn OFF the small pin switch when
finish charged your electronics .
buon will acvate the baery.
Press the “U“ buon for 3 seconds to enter variable
voltage mode. The screen will show you the Puff
counter first followed by the last adjustment (The last
adjustment may be a voltage or waage seng), aer
showing the last adjustment, the iTaste MVP will enter
variable voltage mode. Voltage can be adjusted from
3.3 to 5.0 volts in .1 volt increments by pressing the
“U” buon.
Press the “P“ buon for 3 seconds to enter variable
waage mode. The screen will show you the Puff
counter first followed by the last adjustment (The
last adjustment may be a voltage or waage seng),
aer showing the last adjustment, the iTaste MVP
will enter variable waage mode. Waage can be
adjusted from 6.0 to 11 was in .5 wa increments
by pressing the “P” buon.
Hold both the “P” and “U“ buons simultaneously for
2 seconds. The screen will show a series of readings,
the first being the resistance of the aached load (
Rx.x , for example R2.2), the second being the baery
voltage, the third being the number of puffs since the
device was last turned off and the fourth being the
last set voltage or waage. If no load is aached the
display with show “NON”.
There are three main buons on the iTaste MVP: “ ”
buon, "P" buon and "U" buon; all the funcons
can be acvated by using those three buons to
change sengs in a single step, without the use of a
menu system. Your chosen mode will be displayed on
the digital screen.
Quickly clicking the “ ” buon three mes will enable
or disable the baery. Once enabled, holding down the
Portable power source for electronic products
OPERATION GUIDE
ON/Off:
Variable Voltage Mode :
Variable Waage Mode :
Ohms Meter & Baery Level Indicator & Puff Counter:
7
6
5
4
3
2
1
1
2
5
6
7
3
4
NO. Funcon descripon
iClear dual coil clearomizer
ON/OFF Power buon:
The iTaste MVP baery capacity is displayed via green,
yellow and red LED lights. Green = Fully Charged
Yellow = Half Discharged Red = In need of charging
“P” buon: VW
“U” buon: VV
Portable power source for electronic products
Turn ON this small pin switch when use as power source
for electronic products .
Recharge iTaste MVP with a standard USB Micro cable plug,
it can also work as a passthrough for use while charging.
If you wish to check the number of puffs taken since
the iTaste MVP was last turned off, you can also hold
either the “P” or the “U“ buon to display the Puff
Counter which will be followed by the display of
current mode (VV mode or VW mode). In this state,
you can also adjust the voltage or waage by pressing
the “P” or “U“ buon.
Replace or refill the cartridge if vapor volume decreas-
es.
The manufacturer is not responsible for a damaged
atomizer, cartomizer or clearomizer.
Driving them with too much power for too long or
running them dry can burn them out.
We recommend you start with a low voltage seng
and work your way up unl when you find the right
seng for your atomizers, cartomizers or clearomiz-
ers.
Never use your iTaste MVP without an atomizer,
cartomizer or clearomizer. Connecng to a volt meter
without the load required for high voltages can
damage the device.
When plug in, the LED light will blink from red to
yellow to green , then stay on current baery capacity
level , for example , if your baery current capacity
yellow , then LED light will stay on Yellow , then
change to Green.Aer the iTaste MVP is fully
recharged, the LED lights will turn off.
Recharge iTaste MVP with a standard USB Micro cable
plug, it can also work as a passthrough for use while
charging.
Plug the USB cable into iTaste MVP ’s input and plug
the other end into a power source.
The color of the LED light indicates the remaining
baery life. Aer the iTaste MVP is fully recharged,
the LED lights will turn off.
1.Red LED light = baery voltage is lower than 3.61V
2.Yellow LED light = baery voltage between 3.61V
and 3.75V
3.Green LED light = baery voltage is more than 3.75 V
4.Red LED will keep blinking for 8 seconds when baery
capacity is lower than 3.3V and the device will turn off
automacally.
5.Red LED light will stay on for 5 seconds when a load
short circuit is detected or the current of the coil is
more than 3.5A, then no vapor will be produced.
6.If you take a drag for longer 10 seconds, the baery
will stop it’s output, the RED light will blink 10 mes,
and the iTaste MVP won’t connue to work unl you
press the power buon again.
The LED light will blink in different colors to indicate
the current baery voltage
LED Light Blinking Mode:
Notes:
CHARGING ITASTE MVP