Innova 2.0 User manual

something new in the air
Manuale d’installazione / Installation manual
ehpocaGEO
something new in the air
Installation manual
2.0

2
EN
Compliance
We would first of all like to thank you for having chosen one of our appliances.
We are sure you will be happy with it because it represents the state of the art in the technology of
home air conditioning.
By following the suggestions contained in this manual, the product you have purchased will operate
without problems, giving you optimum room temperatures with minimum energy costs.
Innova S.r.l
This unit complies with European directives:
• Lowvoltage2006/95/EC
• Electro-magneticcompatibility2004/108/EC
• Userestrictionsofhazardoussubstancesinelectrical
andelectronicequipment2011/65/EC(RoHS2)
• Waste electrical and electronic equipment 2002/96/
EC(WEEE).
• Energyconsumptionindicationonthelabelsofenergy-
relatedproducts2010/30/EU
Pictograms in the next chapter provide the necessary
informationforacorrectandsafeuseofthemachineina
rapid,unmistakableway.
Symbols
U
User
- Referstopagescontaininginstructionsorinformation
fortheuser.
I
Installer
- Referstopagescontaininginstructionsorinformation
fortheinstaller.
S
Service
- Referstopagescontaininginstructionsorinformation
for the CUSTOMER TECHNICAL ASSISTANCE
SERVICEinstaller.
Editorial pictograms
Safety pictograms
 Warning
- Itindicatesactionsthatrequirecautionandasuitable
preparation.
 DoNot
- Refers to actions that absolutely must not be
performed.

3
1 4
2 4
3 5
4 5
5 5
6 5
76
8 6
97
1 8
2 8
3 9
4 11
5 11
6 12
713
8 13
9 14
10 14
1 15
2 16
3 17
EN
General
Generalwarnings...............................................................
Fundamentalsafetyrules.........................................................
Description....................................................................
Receiptandunpacking..........................................................
Storage......................................................................
Handling.....................................................................
Shippingdimensionsandweight....................................................
Suppliedcomponents...........................................................
Unitparts .....................................................................
Installation
Installation mode................................................................
Choosingthepositionoftheunit ....................................................
Assemblingtheunit .............................................................
Assemblingairductsandexternalshutters ............................................
Mountingtheapplianceonthebracket ...............................................
Electrical connection ............................................................
High/lowinstallationconfiguration ...................................................
Settingcoolonlyorheatonlymodes .................................................
Touch-screendisplaykeylock.....................................................
Operationstestsandanomalydiagnosis..............................................
Troubleshooting
PeriodicMaintenance
Troubleshooting
Technical data
ThisbookletcodeN273027A-Rev.0-(03/13)consists
of20pages.

4
1.1
1.2
General warning
Fundamental safety rules
 After unpacking, check that the contents are intact
andthatallpartsareincluded. If they're not,please
contacttheAgentwhosoldyoutheappliance.
 The appliance must be installed by an authorised
company. Once the work is done, it must issue a
declaration of conformity to the client in compliance
with current Regulations and with indications on the
instructionmanualsuppliedwiththeappliance.
 These appliances have been designed for
conditioningand/orheatingroomsandtheymustbe
destinedsolelyforthispurposecompatiblywiththeir
performancecharacteristics.
 The manufacturer refuses any contractual or extra-
contractual responsibilities for damage caused to
people, animals or things resulting from incorrect
installation, adjustment, maintenance or improper
use.
 Inthe event of waterleaks, turn off themain switch
andclosethewatertaps.
 Immediately call the Technical Assistance Service
or other qualified personnel and do not intervene
personallyontheappliance.
 Ifthetemperatureissettoolowortoohigh,notonlyit
isunhealthy,butitisalsoauselesswasteofenergy.
 Avoidprolongeddirectcontactwiththeairflow.
 Do not leave the room closed for long. Open the
windowsperiodicallytochangetheair.
 This instruction booklet is an integral part of the
applianceandthereforeitmustbekeptwithcareand
mustALWAYSaccompanytheapplianceevenwhen
the latter is transferred to another owner or user or
transferredto another system.If it getsdamaged or
lost,pleaserequestanothercopytothelocalINNOVA
TechnicalAssistanceService.
 Any repair or maintenance operations must be
performedbytheTechnicalAssistanceServiceorby
qualifiedpersonnelinaccordancewiththisbooklet.Do
notmodifyortamperwiththeapplianceasthiscould
leadtodangeroussituationsandthemanufacturerwill
notbeliableforanydamagecaused.
 Wewouldliketoremindyouthatsomefundamental
safetyrulesshouldbefollowedwhenusingproducts
thatworkwithelectricityandwater;
 Theuseoftheappliancebychildrenandunassisted
disabledpersonsisforbidden.
 Itisforbiddentotouchtheapplianceifbarefootorwith
wetorhumidpartsofthebody.
 Itis forbidden to clean theappliance without having
firstdisconnectedtheappliancefromthemainspower
supplybyturningoffthemainswitch.
 Itisforbiddentomodifysafetyoradjustmentdevices
without authorisation and the indications from the
manufacturer.
 Itis forbidden to pull outor twist the electric cables
coming out of the appliance, even if they are
disconnectedfromthemainspowersupply.
 It is forbidden to introduce objects and substances
throughtheairinletandoutletgrids.
 Itisforbiddentoopentheaccessdoorstotheinternal
parts of the appliance without having turned off the
mainswitchfirst.
 Itisforbiddentodisposeofandleavewithinthereach
ofchildrenthepackingmaterialsastheycouldbea
sourceofdanger.
 Itis forbiddento climbonto theappliance and/orto
placeanytypeofobjectontopofit.
GENERAL

5
S
I
U
1.3
1.4
1.5
1.6
EN GENERAL
Description
"2.0" is the new solution by INNOVA, a significant step
towardsreducingtheaestheticimpactofairconditioners.
Beingonly16centimetresdeep,"2.0"isthethinnestand
lessbulkyinitscategory,thereforeboththeinternaland
externalaestheticimpactiskepttoaminimum.
OptimisedCapacities
Theconditioningcapacitiesof"2.0"havebeenoptimised
soastoobtaintherighttemperatureforthebestlevelof
comfortand,therefore,lessconsumptionandlessnoise.
Thankstothecarefulchoiceofsoundinsulationmaterials,
thenoiseissimilartothatofastandardwallsplitunitand
consumption is drastically contained thanks to the new
directcurrentfan.
162millimetreholes
Animportantchoicenotonlydesign-wise,butalsobecause
ofaconsiderableinstallationadvantage:itiseasiertofind
drillingtoolsasthere'snoneedforprofessionalones,with
loweraestheticimpact.
Easytoinstall
"2.0"canbeinstalledonanyperimeterwalleitherlowor
high.Everythingneededforinstallation(template,support
bracket,holepipesandexternalgrids),excludingthedrill,
isincludedinthebox.
Foldingexternalgrids
"2.0"isequippedwithfoldinggridsactivatedbyinletand
outletair.Theyopenwhentheunitisworkingandclose
whenit'sturnedoff.Betterindoorcomfort,lessdust,noise
and pollution, less maintenance and even less outdoor
visibility.
Remotecontrolandtouch-screendisplay
In addition to the remote control, the touch-screen
display on the unit enables the setting of any function.
There's even a "lock" mode to avoid any improper use.
Itispossibletodeactivatethe"heating"modebysimply
touching the screen. The unit then works in "cool only"
mode, without the need to use the condensation drain
pipe.Theorientationoftheairflapscanalsobeadjusted
bysimplypressingonekey.
Receipt and unpacking
Thepackingismadeofsuitablematerialandcarriedout
byexpertpersonnel.Allunitsarecheckedandtestedand
aredeliveredcompleteandinperfectconditions,however
please perform the following instructions to check the
qualityofshippingservices:
- uponreceipt,checkiftheboxisdamaged.Ifthatis
the case, accept the goods with reservations and
keepphotographicevidenceofanydamagefound
- unpackandcheckthecontentsagainstthepacking
list
- check that none of the parts have been damaged
during shipment. In case of damage, report it to
the shipping company within 3 days of receipt by
registered letter with return receipt and attaching
photographicdocumentation.Acopyshouldalsobe
sent by fax to the MANUFACTURER. No notice of
damagewillbeacceptedafter3daysfromdelivery.
 Keep the packing at least for the whole length of
warranty should you need to ship the appliance to
theservicecentreforrepair.Disposeofthepacking
materials in compliance with current regulations on
wastedisposal.
Storage
Handling
Store the box in a closed environment protected from
atmospheric agents and isolate it from the floor using
planksorpallets.
 Donotturnupsidedown.
Theunitispackedsingularly inacardboardbox.Boxes
caneitherbecarriedsingularlybyhandbytwooperators
orloadedonacart,foramaximumofthreeunits.
 Handlingmustbe performedby qualifiedpersonnel,
withspecifictoolsandwithequipmentsuitableforthe
weightoftheappliance.
 Theapplianceisunbalancedontheright(compressor
side)
 Duringtransportation,theappliancemustbekeptin
verticalposition.

6
S
I
U
1.7
U.M. “2.0” 8 HP "2.0" 10 HP
Kg 48 50
Lmm 1100 1110
Hmm 660 660
P mm 260 260
L
P
H
1.8
A
B
C
D
E
F
G
H
I
L
A
H
D
E
A++
A
L
GG
F
B
C
I
EN
GENERAL
Shipping dimensions and weight
Packaging
Dimensions
Weight
Supplied components
Thesupplycomprisesofthepartslistedin thefollowing
table.Beforeassembly,pleasecheckthattheyareallat
hand.
Externalgridsforairinletandoutletwithsprings(2pcs)
Chains(4pcs)
Screwsandplugskit(6pcs)
Bracketforwallmounting
Useandmaintenancebooklet
Remotecontrol
Papertemplateforholes.
CR20253Vremotecontrolbattery
Wallinletpipes(2pcs)
Energyefficiencylabel

7
S
I
U
1
2
3
4
5
6
7
8
9
10
11
12
1.9
6
8
7
3
4
5
9
2
12
1
10
11
EN GENERAL
Unit parts
Airoutletflaps
Touch-screendisplay
Front panel
Outdoorairsuction
Outdoorairoutlet
Airsuctiongrid
Airfilters
Outdoorairoutletfan
Outdoorairheatexchanger
Compressor
Indoorairheatexchanger
Electronicboard

8
S
I
U
2.1
2.2
60 mm
60 mm
50 mm
120 mm
EN
INSTALLATION
Beforeinstallingtheconditioner,itisessentialtocalculate
thesummerthermalloads(andwinteronesforthemodels
withaheatpump)oftheroom.Themorecalculationsare
exact,thebettertheproductwillwork.Pleaserefertocurrent
regulationsto carry outcalculations. For big installations
pleasecallastudyspecialisedinthermotechnics.Tryto
reducethethermalrefrigerationloadoftheroomfollowing
instructionsbelow:
- Coverlargewindowsexposedtosunlightwithcurtains
orwithexternalmaskings(blinds,porches,reflecting
films,etc.).
- Theroommustremainclosedforaslongaspossible.
- Avoid using halogen lamps or other high energy
consumption appliances such as small ovens, steam
irons,cookingplatesetc.
For a better performance of the appliance and to avoid
malfunctions or dangerous situations, the location of the
unitmustmeetthefollowingrequisites:
- Respect the minimum distances indicated in the
picture.
- Thewallonwhichyouwishtoanchortheunitmustbe
robustandabletosupportitsweight.
- Leave enough space around the unit to perform
maintenanceoperations.
- Nothing must obstruct the air flow both in the top
suctionpart(curtains,plants,furniture)andinthelower
outlet part, as it could cause vibrations which might
preventtheappliancefromworkingcorrectly
 The appliance must be installed against a wall
communicatingwiththeoutside.
 Checkthattherearenostructuresorsystems(beams,
pillars,hydraulicpipes,electricalcablesetc.)inthepart
that must be drilled. Check that nothing is placed in
frontofthe holesthusobstructing theairflow (plants
and leaves, panelling, shutters, thick grates or grids,
etc.)
 Theunitshouldn'tbeinstalledinapositionwherethe
airflowaimsdirectlyatthepeoplenearby;
 Donotforcetheairflapopen;
 The appliance must not be installed directly above
anotherelectrical appliance(TV, radio,fridge, etc.)or
aboveasourceofheat.
INSTALLATION
Installation mode
Choosing the position of the unit

9
S
I
U
2.3
A
B
C
D
555
62,4
18,5
190 104,5 106,4
139
196,8
88 124
293
1008
A
B
C
D
104,1168 168168 168 168
EN INSTALLATION
 Themaximumlengthoftheholesisof1mandthere
must be no bends. Use the supplied grids or grids
withthesamecharacteristics.
Fortheunittowork,twoholesmustbeplacedasindicated
onthetemplate;
The holes on the wall must be drilled using suitable
equipment that facilitates your work and that does not
causedamageorexcessiveinconveniencetoYourclient.
Thebesttoolstomakebigholesonwallsarespecialdrills
(called"coredrills")withahightorqueandwhosespeed
canbeadjustedaccordingtothediameteroftheholeto
makeandtothematerial.Inordertoavoidexcessivedust
anddebrisintheroom,"coredrills"canbecombinedwith
suction systems composed of a vacuum connected to
e.g.asuctioncupplacednexttotheperforationtip.
Inordertomaketheholes,proceedasfollows:
- Placethetemplateprovidedagainstthewallrespecting
the minimum distances from the ceiling, the floor
andthesidewallsasindicatedonthetemplate.The
templatecanbeheldinplaceusingadhesivetape.
- Mark the centre of each hole with a small drill or a
punchbeforeactualdrilling.
- Usingthecoredrill,maketwoholesforinletandoutlet
air.
 Theholesmustbedrilledslightlydownwardstoavoid
waterfromentering.
Themajorityoftheremovedmaterialisexpelledoutwards,
sopleasebecarefulthatitdoesn'thitpeopleorobjects.In
ordertoavoidbreakingtheouterplaster,becarefulwhile
drillingthefinalpartoftheholeandeasethepressureon
thecoredrill.
Drill the 6 holes for the bracket as indicated on the
template.
Theapplianceweightsmoreontheright,somakesureto
secureitproperlyonthisside.Theholesmusthavean8
mmdiametertoaccommodatethe6suppliedplugs.
Inanycase,checkthecharacteristicsandtheconsistency
ofthewalltoseewhetherspecificplugsareneeded.
 The manufacturer cannot be held responsible for
any underestimates of the structural consistency of
theanchoringarrangedbytheinstaller.Wetherefore
encourage you to pay the utmost attention to this
operation as, if performed badly, it could cause
seriousdamagetopeopleandobjects.
Drill a hole in the position indicated on the template for
those heat-pump appliances without a condensation
drain built in the wall in order to enable the draining of
condensation.
HolesforM8plugs
Electrical connection area
ø160mmHolesforairchannelling
ø14mmCondensationdrain
Assembling the unit

10
S
I
U
1 2
300 mm
3%
1
1
2
2
EN
INSTALLATION
For heat pump appliances, a condensation drain pipe
(Ø10mm,internal,notsupplied)mustconnecttheunitto
thepipeonthetoppartoftheappliance.
A solenoid valve will start the flow of the condensation
fromtheinternalcollectiontraywhenthemaximumlevel
hasbeenreached.Forcoolingonlyappliances,saidpipe
mustbeconnectediftheapplianceisgoingtobeused
with low external temperatures (below 23°C). As it's a
gravitydrain,itisessentialforthelinetohaveatleasta3%
slopeminimumineverypoint.Arigidorflexiblepumpcan
beusedwithaminimuminternaldiameterof10mm.Ifthe
lineflowsintoasewagesystem,itisnecessarytoperform
asiphoningoperationbeforeinsertingthepipeinthemain
drainage.Saidsiphonmustbeplacedatleast300mm
underthemouthoftheappliance.
 Ifthelineflowsintoa container(e.g.atank),donot
closethecontainerhermeticallyandavoidimmersing
thedrainingpipeintothewater.
 Theholeforthecondensationpipemustalwayslean
towardstheoutside.
 Theexactpositioninwhichtoplacethepipemouthis
indicatedonthetemplate.
 Check that the expelled water does not cause any
damage or problems to people or objects. During
winter,thiswatermaycreatesheetsoficeoutside.
 Whenconnectingthecondensationdrain,becareful
nottosqeezetherubberduct.
 It is possible to empty the collection tray using the
safetydrainatthebaseoftheapplianceifnecessary.
Condensation drain predisposition
Safetydraintoemptytray Condensationdrainduct

11
S
I
U
1 2
A
B
C
2.4
2.5
1
2
2
B
A
C
EN INSTALLATION
Bracket Bracketanchoringpoints
Junction line
Hook
Flap in vertical position
Once the holes have been made, place the supplied
plasticsheetsinsidethem.
Rollupthesheetandinsertitinthehole,checkingthatthe
Ajunctionlineisaimingupwards.
Useacuttertoremoveanyexcesspipe.
Toplacetheexternalgrids,proceedasfollows:
- connectthechainstotheendsofthesprings;
- foldtheexternalshutters;
- insertyourarmintheholetopushtheshutteroutside
while holding the ends of the chains with the other
handtopreventthemfromfallingdown;
- opentheshutterinsidethehole;
- rotate the shutter to bring the flap in the vertical C
positionandcheckthattheclosingmechanismworks;
- pullthechainsbytensioningthesprings;
- useaboltcuttertoremoveanyexcesschain.
- anchorthehookofthechaintowallB.
 Use only the supplied grids or grids with the same
characteristics.
Aftercheckingthatthebracketisanchoredtothewalland
thatallnecessaryelectricalconnectionsandcondensation
drainpredispositionshavebeenmade,youcanmountthe
conditioner. Lift it by the sides of the bottom base until
thebracketfitsonalloftherightspotsontheappliance.
In order to ease the operation, slightly tilt the appliance
towardsyou.
Direct electrical connections (disconnecting the power
supplycable)andtheanchoringofthecondensationdrain
must be carried out after having spaced the appliance
fromthewallusingawoodenwedgeoranyothersimilar
object.
Oncetheworkisdone,checkthattherearenoopenings
on the back of the appliance, especially where the air
ductsareconnected.
Assembling air ducts and external shutters
Mounting the appliance on the bracket

12
S
I
U
2.6 Electrical connection
A
B
A B
EN
INSTALLATION
The appliance is equipped with a power cord and plug
(Y-typeconnection,thecordcanonlybereplacedbythe
manufacturer,theassistancecentreoraqualifiedinstaller).
Ifusingasocketneartheappliance,inserttheplug.
 Beforeconnectingtheconditionercheckthat:
- The power supply voltage and frequency values
complywiththedataplateoftheappliance.
- Thepowersupplylineisprovidedwithasuitableearth
connectionandthatitisdimensionedforthemaximum
absorptionoftheconditioner(minimumcablesection
equalto1.5mm2).
- Powerisonlysuppliedusingasuitablesocketthrough
thesuppliedplug.
 Thepowercordmustbereplacedonlybythetechnical
assistanceserviceorbyauthorisedpersonnel.
 The appliance must be connected to 230V/50Hz
mainsviaanomnipolarswitchwithacontactopening
distance of minimum 3 mm, or using a device
enablingthecompletedisconnectionoftheappliance
inovervoltageIIIcategoryconditions.
Itispossibleto carryoutthe electricalconnectionusing
a cable inside of the wall as indicated in the installation
template(recommendedforinstallationsintheupperpart
ofthewall).
Please check that the power supply is provided with
suitableprotectionsagainstoverloadsand/orshort-circuits
(using a 10 at delay fuse or other equivalent devices is
recommended).
 Thisoperationmustbeperformedonlybytheinstaller
orbyauthorisedpersonnelincompliancewithcurrent
nationalregulations
Itisessentialtodisconnectthemainswitchbeforemaking
anyconnectionormaintenanceoperationinordertoavoid
anyriskofelectrocution.
Tocarryoutdirectconnectionsandsubstitutethepower
cordusingthecableinthewall,proceedasfollows:
- Space the appliance from the wall using a wooden
wedgeorasimilarobject.
- Disconnect the power cord by unscrewing the 3
screwsfromtheterminalboard.
- Connectthewallcablecheckingthatthepowersupply
lineisprovidedwithasuitableearthconnectionand
thatitisdimensionedforthemaximumabsorptionof
theconditioner(minimumcablesectionequalto1.5
mm2).
 These operations must be carried out with the
appliance already placed on the bracket, therefore
read the following instructions carefully before
completingtheconnection.
WhentheCPcontactopens(connectedtoafreenon-live
contact)theapplianceisputisstand-byandCPappears
onthedisplay.
Using this contact, it is possible to connect an external
device that inhibits the functioning of the appliance
such as: open window contact, remote on/off, infrared
presencesensor,qualificationbadge,etc.
CP presence contact input connection
230V/50HzElectricalpowersupplyterminalboard CPpresencecontact

13
S
I
U
2.7
2.8
High/low installation configuration
Setting cool only or heat only modes
A
B
1
A
B
1
1
EN INSTALLATION
Theunitcanbeinstalledeitherinthelowerpart(nearthe
floor)orintheupperpart(neartheceiling)ofthewall.In
ordertooptimiseairdistributionandcomfort,thedirection
oftheairflowcanbemodifiedbyadjustingthepositionof
theairflap.
Theapplianceissuppliedreadytobeinstalledinthelower
partofthewall,soairisdispensedupwards.Thesame
configurationcanalsobeusedintheupperpartofthewall
incoolingmode,whichincreasestheairflowintheroom
(coandaeffect).
 Thisoperationmustbeperformedwhiletheappliance
isswitchedoffanddisconnected.
- Opentheairoutletflapgently
- Removetheflapopeningblockinsertlocatedinternally
ontherightoftheairoutletmouthandplaceitinthe
lowerhole.
Afteradjustingtheairoutletflapposition,itisnecessaryto
setuptheelectroniccontroloftheappliance:
- Keep pressed the  button on the display for 5
seconds;
- Thedn(lowerwall)symbollightsuponthedisplay
- Pressthe buttonagain;
- TheuP(upperwall)symbollightsuponthedisplay.
- Ifnootheroperationsareperformedinthefollowing2
seconds,thenewsettingismemorised.
 For the appliance to work properly, each time the
configuration of the air outlet flap is modified, the
electroniccontrolmustbeset.
It is possible to deactivate the heating or the cooling
modesfollowingasimpleprocedure.
KeeptheAkeyonthetouch-screendisplaypressedfor
5secondsuntilHC(heatingandcooling)appearsonthe
display.
Press the A key for 1 second for the Co (cooling only)
mode.
PresstheAkeyagainforHo(heatingonly)mode.
Waitfor3secondswithouttouchinganythingtomemorise
thesetting.
Adjust the air outlet flap configuration from the lower wall position to the upper wall position.
Highinstallation
Lowinstallation(factorysettings)
Block insert

14
S
I
U
2.9
2.10
EN
INSTALLATION
Should any anomaly occur in the condensation water
system, the maximum level float blocks the conditioner
andtheOFcodeappearsonthedisplay.
Duringcoolinganddehumidification,electronicsswitches
the compressor off and keeps the water distribution
systemactivewiththebattery-togetherwiththefan-to
disperse excess water in the container.  If the problem
persists,pleasecontacttheassistanceservice.
Duringheating,condensationsshoulddrainfreelythrough
the specific pipe. In the event of an alarm, check that
the condensation pipe is not bent or obstructed, thus
preventingthewaterfromflowingout.
Beforeleaving,collectthepackingandcleananyduston
theappliancewithadampcloth.Theseoperations,though
notstrictlyessential,transmitasenseofprofessionalism
totheUser.
In order to avoid useless calls from the User, before
leaving:
- explainthecontentsoftheManual,
- explainhowtocleanthefilter.
- clarifywhenandhowtocalltheAssistanceService.
Emergency condensation air discharge
Operations after installing
If the presence contact is not closed, the appliance
doesn'tstartandtheCPalarmappearsonthedisplay.
ThekeylockisactivatedbykeepingtheTimer symbol
on the touch-screen display pressed for three
seconds.
Anyactionispreventedbytheuser.
Thestand-bysymbolflashesat1secondintervals.
Todeactivatethelock,keeptheTimersymbolpressedfor
threesecondsonceagain.
Anykeyontheremotecontroldeactivatesthelock!
Open CP contact
Touch-screen display key lock
Display code Cause
E1 BrokenroomtemperatureRTprobe
E2 BrokenevaporativebatteryIPTprobe
E3 BrokenoutdoorairtemperatureOTprobe
E4 BrokenconditionerbatteryOPTprobe
E5 Brokenindoorairfanmotor
E6 Brokenoutdoorairfan
E7 Lackofcommunicationwiththedisplay
Theconditionercanperformashortself-diagnosiscycle
tocheckthetemperaturesdetectedbythe4probesand
thestatusofthe3inlets.
Inordertoactivatetheself-diagnosisfunction,pressthe
 button within 10 seconds from the electric power
supply.
Thedisplaywilllitallsymbolsfor2secondsandthenitwill
showthe7informationat2secondintervals.
After5cycles, orwhen anykey ispressed eitherinthe
display or on the remote, the self-diagnosis mode will
stop.
Iftheconditionerblocksbecauseofanalarm(seefollowing
table),pleasecommunicatetotheassistancecentrethe
codeonthedisplaytofacilitateinterventions.
Operations tests and anomaly diagnosis

15
S
I
U
3.1
1
2
3
EN MAINTENANCE
MAINTENANCE
 Before any cleaning and maintenance operation,
disconnect the unit from the mains by switching off
themainswitch.
 Waituntilthepartshavecooleddowntoavoidgetting
burned.
 Donotuseabrasivespongesorabrasiveorcorrosive
detergentstoavoiddamagingvarnishedsurfaces.
Whennecessary,cleantheexternalsurfaceswithasoft
dampcloth.
Theairconditioneryouhaveboughthasbeendesigned
tokeepmaintenanceoperationstoaminimum,whichonly
concernthefollowingcleaningoperations:
- Cleantheairfilterafteraperiodofcontinuoususeand
inaccordancewiththeconcentrationofimpuritiesin
the air, or when you wish to start-up the appliance
afteraperiodofinactivity.
 Thefilterisplacedonthetoppartoftheappliance.
Toextractthefilters:
- openthegridandremoveit;
- extractthefiltersbyliftingthem;
- removethedustfromthefilterwithavacuumcleaner
orwashingitinrunningwaterwithoutusingdetergents
orsolventsandleavetodry;
- putthefiltersbackontopofthebatteries,takingcare
topositionthemcorrectly;
- putthegridback.
 Check that the panel is mounted correctly after
cleaningoperations.
 Usingtheappliancewithoutthenetfiltersisprohibited
Theairconditioneryouhaveboughthasbeendesigned
tokeepmaintenanceoperationstoaminimum,whichonly
concernthefollowingcleaningoperations.
Periodic Maintenance
Cleaning filtering seats
External cleaning

16
S
I
U
3.2 Troubleshooting
EN
MAINTENANCE
In case of malfunctioning, please refer to the following table. If,
afterperformingthesuggestedchecks,theproblemisnotsolved,
pleasecontacttheauthorisedtechnicalassistance.
Analarmcodeappearsonthedisplayincaseofanomalies.Some
ofthefunctionsremainactive(seeFUNCTIONINGcolumn)
Theonlywaytosolvetheproblemistodisconnectandconnectthe
appliance.Ifthealarmstillappears,pleasecontacttheauthorised
technicalassistance.
Display alarms
Anomaly Possible cause Solution
The appliance
doesn't switch
on
Nopowersupply
Checkthevoltage(byturningthelighton,forexample).
Checkthattheexclusivemagneto-thermicswitchthatprotects
theappliancehasn'tintervened(ifithas,resetit).Iftheproblem
repeats immediately, please call the Service Centre and avoid
tryingtomaketheappliancework.
Batteries ran out Checkthattheapplianceturnsonusingthetouch-screendisplay
andsubstitutethebatteries.
The appliance
does not cool/
heatenough.
Thesettemperatureistoohighortoo
low.
Checkand
adjust the temperature on the remote
Theairfilterisclogged Checktheairfilterandcleanitifnecessary
Checkthattherearenootherobstacles
oftheairflowbothinsideandoutside. Removeanythingthatmightblocktheairflow.
The thermal refrigeration load has
increased (for example, a door or
a window has been left open or an
appliance has been installed in the
room,generatingalotofheat).
Trytoreducethethermalrefrigerationloadoftheroomwiththe
followingadvice:
Coverlarge windowsexposed to sunlightwith curtainsor with
externalmaskings(blinds,porches,reflectingfilms,etc.);
Theroommustremainclosedforaslongaspossible;
Avoidturningonhalogenlampsorotherhighenergyconsumption
appliancessuchassmallovens,steamirons,cookingplatesetc.
Alarm displayed Cause Functioning
E1 BrokenroomtemperatureRT
sensor
It is still possible to activate the Cooling, Dehumidification and
Heatingmodes.  It only monitors theantifreeze function of the
internalbattery.
E2 Broken internal battery IPT
sensor Noneofthefunctioningmodesworks.
E3 Broken outside temperature
OTsensor Noneofthefunctioningmodesworks.
E4 Broken outside battery OPT
sensor
It is still possible to activate the Cooling, Dehumidification and
Heatingmodes.Defrostingisperformedatfixedtimes.
E5 Broken internal ventilator
motor Noneofthefunctioningmodesworks.
E6 Broken external ventilator
motor Noneofthefunctioningmodesworks.
E7 Lack of communication with
thedisplay Noneofthefunctioningmodesworks.
CP OpenCPcontact Theapplianceonlyworksifthecontactisclosed.Checkthatthe
clampsareconnected.
OF Maximumlevelfloat
intervention
During cooling and dehumidification, electronics switches the
compressoroffand keepsthe waterdistributionsystem active
with the battery - together with the fan - to disperse excess
water in the container.  During heating, condensations should
drainfreelythroughthespecific pipe.Intheeventof analarm,
checkthatthecondensationpipeisnotbentorobstructed,thus
preventingthewaterfromflowingout.

17
S
I
U
3.3
U.M. “2.0” 8 HP "2.0" 10 HP
kW 1.65 2.30
kW 1.70 2.25
W 580 850
W 545 725
kWh 290 425
l/h 0.8 1.1
V-F-Hz 230-1-50 230-1-50
W/W 2.84 2.71
W/W 3.12 3.1
A A
A A
No. 3 3
mm 1030x555x170 1030x555x170
Kg 46 48
dB(A) 29/38 32/41
mm 162 162
R-410A R-410A
18°C/-5°C 18°C/-5°C
5°C/-10°C 5°C/-10°C
DB27°C-WB19°C DB35°C-WB24°C
DB20°C-WB15°C DB7°C-WB6°C
EN MAINTENANCE
Technical data
Pleaseread thedata plates toobtain thetechnical data
listedbelow.
- Powersupplyvoltage
- Maximumabsorbedpower
- Maximumabsorbedcurrent
- Amountofrefrigerantgas
- Casingprotectionlevel
- Max.workingpressure
* Noisepressuremeasured1mawayand1.5mhigh  RelevantregulationEN14511.1.2.3.4
Operating limits
Technical data
Coolingpower(1)
Heatingpower(2)
Powerabsorbedwhencooling(1)
Powerabsorbedwhenheating(2)
Annualenergyconsumptionforcooling(1)
Dehumidificationcapacity
Powersupplyvoltage
EER
COP
Energyefficiencyratiowhencooling
Energyefficiencyrationwhenheating
Internal-externalventilationspeed
Dimensions(WxHxD)
Weight
Noiselevel(min-max)*
Wallholesdiameter
Refrigerantgas
Minimumcoolingtemperatures(internal/external,DB)
Minimumheatingtemperatures(internal/external,DB)
Room t External t
Test conditions
Coolingmodetests(1)
Heatingmodetests(2)

18
S
I
U
EN
NOTES

19
S
I
U
EN NOTES

INNOVA s.r. l .
Fraz . St rada, 16 - 38085 PIEVE DI BONO (TN) - ITALY
tel. [phone] fax [phone]
[email protected]
realised with iés technology by
N273027A - Rev. 0
INNOVA s.r. l .
Fraz . Strada, 16 - 38085 PIEVE DI BONO (TN) - ITALY
tel. [phone] fax [phone]
[email protected]
realised with iés technology by
N273027A - Rev. 0