Innovative Concepts in Entertainment Monopoly Roll -N- Go User manual

Monopoly Roll -N- Go Marquee Three Cabinet Assembly Guide
Innovative Concepts in Entertainment
10123 Main Street
Clarence, NY 14031
[phone] Service Department

AC Splitter for Network Switch adaptor.
Long AC power Cable.
Long extension cable.
Keys and hardware.
What is included with your Marquee for A Three Cabinet Install
Another network cable for the upper sign.
You should have a total of three.
USB A to B cable.
DVI to Display port cable
Network switch, AC adaptor and 3 network cables.
Rev D

Installing the Marquee on top of three games.
Step 2:
Unlock the back covers from the left and
right mounts. Facing the back of the game,
the cabinet to the right will have the mount
that contains all the electronics.
The cabinet to the left will have the mount
with no electronics.
Step 1:
Position the two games leaving
1/2” between them at the front.
1/2”
1/2”

Step 3:
Secure the cabinet mounts to the top of the
cabinets. Use four AA6220 bolts and
AA6070 washers.
Make sure the mount with the
electronics are on top of the
cabinet on the left looking at
the front of the game
(right if from the back!).

Step 4:
Slide the right upper assembly over and onto the mounts as shown.
Step 5:
Secure it to the mounts using three AA6212 bolts and three AA6281 washers.
Attach harnesses shown.

Step 6:
Slide the left upper assembly over and onto the mounts as shown. Then secure using three
AA6281 bolts and three AA6212 washers. Attach harnesses shown.
Step 7:
At each side of the center display are the
mounting inserts. They are shown within the
circles. They insert into slots in each of the top
signs. One of those slots are shown.
Insert the center display into the two slots.

Step 8:
Secure the display using two AA6281 bolts and AA6212 washers.
Location is shown with the yellow circles with arrows.
Step 9:
Slide the sign onto the poles.
Attach harnesses shown.

Step 11:
Plug the long AC cord in to the side of the cabinet.
Make sure switch is set to on (1).
Step 12:
Plug in the USB cable and DVI to
display port cable into the marquee
electronics box.
GAME 1GAME 2GAME 3

Step 13:
Attach the two wire channel covers. Carefully wire tie all wires and neatly tuck them inside this
channel. Secure the wire channel using two bolts and washers.
Step 14:
At the back of the game 1, connect the display port connector (DVI to display port
cable) to the video card’s display port connection (NOT MOTHERBOARD!). Then
connect the USB cable in any available USB connector.

Step 15:
Unplug one of the AC connections at the bottom of the game and next to the power
module. Then plug the AC Y-splitter into where you unplugged the AC connector.
You should now have a AC outlet to plug the network switch power adaptor into.
Step 16:
Plug the AC power adaptor for the network switch into the AC outlet you just added.
Then connector a network cable from the network switch to each computer’s network
connector.

Step 22:
Open the operator panel at the bottom of the cabinet. Press the program button to
enter the main menu. Navigate to the system settings of each game.
On the left game set mega marquee master to on and then set machine ID to 1.
On the middle game set Mega marquee master to off and set machine ID to 2.
On the right game set Mega marquee master to off and set machine ID to 3.

MY DISPLAY IS UPSIDE DOWN!!
Open the operator panel at the bottom of the cabinet. Press the program button to
enter the main menu. Navigate to the system settings of each game.
On the left machine navigate to the system settings and increase the value of
the mega marquee LED angle. Keep doing so until the display is correct.