Inova Maxi Climber XL User manual

SAFETY INSTRUCTIONS
¡IMPORTANT!
READ THIS MANUAL CAREFULLY BEFORE USING THIS PRODUCT. THE MANUFACTURER ASSUMES NO
RESPONSIBILITY FOR DAMAGE OR INJURY TO THE USER OR PROPERTY BY THE USE OF THIS EQUIPMENT.
SAFETY INSTRUCTIONS AND MAINTENANCE
• The owner of the equipment is responsible to
ensure that all users of it are informed of safety
measures and proper use.
• Use the equipment only as described in this manual.
• Place the product on a flat, stable surface, with at
least 2 meters of clearance around it. It is recommended
to place a blanket under the equipment to protect
the floor or carpet from any damage.
• Keep the assembling area clean and well lit. Untidy
and dark areas can lead to accidents.
• Keep the equipment indoors, away from moisture
and dust. Do not place it in the garage, cottage,
shed, conservatory, patio, garden, etc. or near water
or liquids. Ignoring this instruction may cause serious
safety and electrical problems.
• Do not operate the equipment where aerosol products
are being used or oxygen is being provided.
• Keep children under 12 years old and pets away
from the equipment at all times. Do not leave children
unattended in the same room with the equipment.
• People with disabilities should not use the equipment
without supervision of qualified personnel.
• People with malignant tumors, preexisting conditions,
under treatment, heart disease or any electronic
device implanted in the body, should consult their
doctor before using the equipment.
• This equipment should not be used by pregnant
women.
• Never allow more than one person at a time using
the equipment.
• Do not use the equipment if you feel tiredness or
under the effect of narcotics, drugs or alcohol.
• Do not use the equipment if indoors temperature
is over 40°C.
• Always wear appropriate workout clothing when
exercising. Do not wear loose clothing, jewelry or
accessories that could be caught in the mechanical
parts. It is recommended to wear gym clothes for
both men and women.
• If the user feels dizziness, nausea, chest pain or
any other abnormal symptoms, he should stop exercising
and consult a physician immediately.
• This equipment is only for domestic use. Do not
use it for commercial purposes.
• Never useabrasivesor solventstocleantheequipment.
To prevent damage to the computer, keep liquids
away from it and avoid direct sunlight as well.
• After each workout wipe the computer and other
surfaces with a soft cloth dampened with water or
a dried one, to remove the perspiration on it.
• Check and adjust every part regularly. Replace any
damaged part immediately.
• If it is necessary, contact any authorized technical
service. The equipment should be serviced by
a qualified specialist using only standard spare
parts.
• Be careful when using or moving the equipment in
order to avoid physical injuries.
• Proper maintenance of the product is very important
to ensure optimal operation. Improper maintenance
or lack thereof, can damage the equipment life.
• Do not modify its incline by placing objects underneath.
Keep this user manual in a safety place for future reference.

PARTS LIST

PARTS LIST

EXPLODED DIAGRAM

ASSEMBLY DIAGRAM
Make sure that all pieces
are well tightened before
using the equipment.
Already
assembled
Correct order
READY TO
USE!
25
25
88
0
25
45
*
*
A
2
1
25
34
34
24 75
34
Height is adjustable
Detach the hydraulic cylinder
from the adjusted tubes (8)
and put back into the cylinder
bracket.
11R
49
10
11L
30L
31R
30L
30A
14
67
66
66
67
70
7
74
Floor
stabilizers can
rotate to avoid
movement on
the floor.
YOUR PERSONAL FITNESS COACH ON DEMAND
MAXIMIZE YOUR ROUTINE AND BURN MORE CALORIES
L
R
Be sure the curved
part is in the frontal
direction
To adjust the pressure of the
resistance pistons, turn the
knob and align the number
(1 low - 12 high) with the
large arrow. Repeat in both
pistons.
9
75
8
15
18 17
72
75
A
C
A
B
AB
B
A
C
C
A
72
1
25
30
12
8
31A
31
13
24
25 30A
72
2
18
18
17
17
18
17
18
17
4
11
11
70
67
66 66
14
67
19
19
59
59
49
9
10
49
20
74 75
2019
59
20
59
20
19
19
19
13
12
7
B
A
74

PREPARATION
• Before the assembly, make sure you have plenty
of space around the product.
• Use the tools provided with the product as indicated
in this manual.
This product should be used for people whose body
weight does not exceed 300lbs (136 kg).
STEP 1
A. Remove the knob (25) onto the front support tube
(8) by turning it counterclockwise.
B. Fully unfold the item. Be careful not to pinch your
fingers at the middle of the foldable tubes.
C. Insert the knob (25) into middle hole of foldable
tubes and turn it clockwise.
STEP 1
ASSEMBLY INSTRUCTIONS
Make sure that all pieces
are well tightened before
using the equipment.
Already
assembled
Correct order
READY TO
USE!
25
25
88
0
25
45
*
*
A
2
1
25
34
34
24 75
34
Height is adjustable
Detach the hydraulic cylinder
from the adjusted tubes (8)
and put back into the cylinder
bracket.
11R
49
10
11L
30L
31R
30L
30A
14
67
66
66
67
70
7
74
Floor
stabilizers can
rotate to avoid
movement on
the floor.
YOUR PERSONAL FITNESS COACH ON DEMAND
MAXIMIZE YOUR ROUTINE AND BURN MORE CALORIES
L
RBe sure the curved
part is in the frontal
direction
To adjust the pressure of the
resistance pistons, turn the
knob and align the number
(1 low - 12 high) with the
large arrow. Repeat in both
pistons.
9
75
8
15
18 17
72
75
A
C
A
B
AB
B
A
C
C
A
72
1
25
30
12
8
31A
31
13
24
25 30A
72
2
18
18
17
17
18
17
18
17
4
11
11
70
67
66 66
14
67
19
19
59
59
49
9
10
49
20
74 75
2019
59
20
59
20
19
19
19
13
12
7
B
A
74

STEP 2
A. Remove both knobs (25) at each side of the cylinder
bracket (45) by turning them counterclockwise.
B. Attach the cylinders (34) to the adjustment tubes.
Align the holes of the cylinders, insert and tighten
knobs (25).
STEP 2
ASSEMBLY INSTRUCTIONS
C. Attach the loose wire (*) passing through position A
to the interior welded bolt and tighten it with the
nut (24) as shown in the picture. Use the wrench
(75) provided.
Make sure that all pieces
are well tightened before
using the equipment.
Already
assembled
Correct order
READY TO
USE!
25
25
88
0
25
45
*
*
A
2
1
25
34
34
24 75
34
Height is adjustable
Detach the hydraulic cylinder
from the adjusted tubes (8)
and put back into the cylinder
bracket.
11R
49
10
11L
30L
31R
30L
30A
14
67
66
66
67
70
7
74
Floor
stabilizers can
rotate to avoid
movement on
the floor.
YOUR PERSONAL FITNESS COACH ON DEMAND
MAXIMIZE YOUR ROUTINE AND BURN MORE CALORIES
L
RBe sure the curved
part is in the frontal
direction
To adjust the pressure of the
resistance pistons, turn the
knob and align the number
(1 low - 12 high) with the
large arrow. Repeat in both
pistons.
9
75
8
15
18 17
72
75
A
C
A
B
AB
B
A
C
C
A
72
1
25
30
12
8
31A
31
13
24
25 30A
72
2
18
18
17
17
18
17
18
17
4
11
11
70
67
66 66
14
67
19
19
59
59
49
9
10
49
20
74 75
2019
59
20
59
20
19
19
19
13
12
7
B
A
74

Make sure that all pieces
are well tightened before
using the equipment.
Already
assembled
Correct order
READY TO
USE!
25
25
88
0
25
45
*
*
A
2
1
25
34
34
24 75
34
Height is adjustable
Detach the hydraulic cylinder
from the adjusted tubes (8)
and put back into the cylinder
bracket.
11R
49
10
11L
30L
31R
30L
30A
14
67
66
66
67
70
7
74
Floor
stabilizers can
rotate to avoid
movement on
the floor.
YOUR PERSONAL FITNESS COACH ON DEMAND
MAXIMIZE YOUR ROUTINE AND BURN MORE CALORIES
L
R
Be sure the curved
part is in the frontal
direction
To adjust the pressure of the
resistance pistons, turn the
knob and align the number
(1 low - 12 high) with the
large arrow. Repeat in both
pistons.
9
75
8
15
18 17
72
75
A
C
A
B
AB
B
A
C
C
A
72
1
25
30
12
8
31A
31
13
24
25 30A
72
2
18
18
17
17
18
17
18
17
4
11
11
70
67
66 66
14
67
19
19
59
59
49
9
10
49
20
74 75
2019
59
20
59
20
19
19
19
13
12
7
B
A
74
STEP 3
A. Attach front stabilizer (2) to the base of front support
tube (8) and fasten with two large bolts (72) two
curved washers (17) and two dome nuts (18). Use
the provided wrench (75).
STEP 3
ASSEMBLY INSTRUCTIONS
B. Attach rear stabilizer in U (1) to the base of aluminum
track (15) and fasten with two large bolts (72) two
curved washers (17), and two dome nuts (18). Use
the provided wrench (75).

Make sure that all pieces
are well tightened before
using the equipment.
Already
assembled
Correct order
READY TO
USE!
25
25
88
0
25
45
*
*
A
2
1
25
34
34
24 75
34
Height is adjustable
Detach the hydraulic cylinder
from the adjusted tubes (8)
and put back into the cylinder
bracket.
11R
49
10
11L
30L
31R
30L
30A
14
67
66
66
67
70
7
74
Floor
stabilizers can
rotate to avoid
movement on
the floor.
YOUR PERSONAL FITNESS COACH ON DEMAND
MAXIMIZE YOUR ROUTINE AND BURN MORE CALORIES
L
RBe sure the curved
part is in the frontal
direction
To adjust the pressure of the
resistance pistons, turn the
knob and align the number
(1 low - 12 high) with the
large arrow. Repeat in both
pistons.
9
75
8
15
18 17
72
75
A
C
A
B
AB
B
A
C
C
A
72
1
25
30
12
8
31A
31
13
24
25 30A
72
2
18
18
17
17
18
17
18
17
4
11
11
70
67
66 66
14
67
19
19
59
59
49
9
10
49
20
74 75
2019
59
20
59
20
19
19
19
13
12
7
B
A
74
STEP 4
A. Attach the left pedal strap (30A) onto the left pedal
(30L). Make sure that the curved part is aligned
with the front part of the pedal.
STEP 4
ASSEMBLY INSTRUCTIONS
B. Attach the left pedal (30L) to the left adjusting
tube (9) and tighten by turning it clockwise using
the wrench provided (75).
C. Repeat the procedure with the right pedal strap
(31A) and the right pedal (31R).

Make sure that all pieces
are well tightened before
using the equipment.
Already
assembled
Correct order
READY TO
USE!
25
25
88
0
25
45
*
*
A
2
1
25
34
34
24 75
34
Height is adjustable
Detach the hydraulic cylinder
from the adjusted tubes (8)
and put back into the cylinder
bracket.
11R
49
10
11L
30L
31R
30L
30A
14
67
66
66
67
70
7
74
Floor
stabilizers can
rotate to avoid
movement on
the floor.
YOUR PERSONAL FITNESS COACH ON DEMAND
MAXIMIZE YOUR ROUTINE AND BURN MORE CALORIES
L
RBe sure the curved
part is in the frontal
direction
To adjust the pressure of the
resistance pistons, turn the
knob and align the number
(1 low - 12 high) with the
large arrow. Repeat in both
pistons.
9
75
8
15
18 17
72
75
A
C
A
B
AB
B
A
C
C
A
72
1
25
30
12
8
31A
31
13
24
25 30A
72
2
18
18
17
17
18
17
18
17
4
11
11
70
67
66 66
14
67
19
19
59
59
49
9
10
49
20
74 75
2019
59
20
59
20
19
19
19
13
12
7
B
A
74
STEP 5
A. Attach the left middle handlebar (12) to the roller
support part (7) and tighten with one washer (19)
and one Allen bolt (20) on the front side and one
washer (19) and one Allen bolt M8*40L (59) on
STEP 5
ASSEMBLY INSTRUCTIONS
the upper side. Bolts and washers are pre-assembled.
Use the Allen key provided (74).
B. Repeat this procedure with the right middle
handlebar (13).

Make sure that all pieces
are well tightened before
using the equipment.
Already
assembled
Correct order
READY TO
USE!
25
25
88
0
25
45
*
*
A
2
1
25
34
34
24 75
34
Height is adjustable
Detach the hydraulic cylinder
from the adjusted tubes (8)
and put back into the cylinder
bracket.
11R
49
10
11L
30L
31R
30L
30A
14
67
66
66
67
70
7
74
Floor
stabilizers can
rotate to avoid
movement on
the floor.
YOUR PERSONAL FITNESS COACH ON DEMAND
MAXIMIZE YOUR ROUTINE AND BURN MORE CALORIES
L
RBe sure the curved
part is in the frontal
direction
To adjust the pressure of the
resistance pistons, turn the
knob and align the number
(1 low - 12 high) with the
large arrow. Repeat in both
pistons.
9
75
8
15
18 17
72
75
A
C
A
B
AB
B
A
C
C
A
72
1
25
30
12
8
31A
31
13
24
25 30A
72
2
18
18
17
17
18
17
18
17
4
11
11
70
67
66 66
14
67
19
19
59
59
49
9
10
49
20
74 75
2019
59
20
59
20
19
19
19
13
12
7
B
A
74
STEP 6
A. Release the knob (49) of the right adjusting tube
(10) by turning it counterclockwise.
B. Insert the right upper handlebar (11R) into the
right adjusting tube (10) and tighten it with the
STEP 6
ASSEMBLY INSTRUCTIONS
knob (49) by turning it clockwise to adjust in the
desired position.
C. Repeat the procedure with the left upper handlebar
(11L).

Make sure that all pieces
are well tightened before
using the equipment.
Already
assembled
Correct order
READY TO
USE!
25
25
88
0
25
45
*
*
A
2
1
25
34
34
24 75
34
Height is adjustable
Detach the hydraulic cylinder
from the adjusted tubes (8)
and put back into the cylinder
bracket.
11R
49
10
11L
30L
31R
30L
30A
14
67
66
66
67
70
7
74
Floor
stabilizers can
rotate to avoid
movement on
the floor.
YOUR PERSONAL FITNESS COACH ON DEMAND
MAXIMIZE YOUR ROUTINE AND BURN MORE CALORIES
L
RBe sure the curved
part is in the frontal
direction
To adjust the pressure of the
resistance pistons, turn the
knob and align the number
(1 low - 12 high) with the
large arrow. Repeat in both
pistons.
9
75
8
15
18 17
72
75
A
C
A
B
AB
B
A
C
C
A
72
1
25
30
12
8
31A
31
13
24
25 30A
72
2
18
18
17
17
18
17
18
17
4
11
11
70
67
66 66
14
67
19
19
59
59
49
9
10
49
20
74 75
2019
59
20
59
20
19
19
19
13
12
7
B
A
74
STEP 7
A. Attach the cellphone support frame (14) to the
roller support part (7) and tighten it with two flat
washers (67) and two cross head bolts (66).
B. Loosen and pull out the preassembled cross head
bolt (66) and the flat washer (67) of the cellphone
STEP 7
ASSEMBLY INSTRUCTIONS
clamp (70). Attach the cellphone clamp (70) to the
cellphone support frame (14) and tighten with the
flat washer (67) and the cross head bolt (66). Use
the Allen key (74) provided.
Make sure that all pieces are well tightened, before
using the equipment.

Make sure that all pieces
are well tightened before
using the equipment.
Already
assembled
Correct order
READY TO
USE!
25
25
88
0
25
45
*
*
A
2
1
25
34
34
24 75
34
Height is adjustable
Detach the hydraulic cylinder
from the adjusted tubes (8)
and put back into the cylinder
bracket.
11R
49
10
11L
30L
31R
30L
30A
14
67
66
66
67
70
7
74
Floor
stabilizers can
rotate to avoid
movement on
the floor.
YOUR PERSONAL FITNESS COACH ON DEMAND
MAXIMIZE YOUR ROUTINE AND BURN MORE CALORIES
L
RBe sure the curved
part is in the frontal
direction
To adjust the pressure of the
resistance pistons, turn the
knob and align the number
(1 low - 12 high) with the
large arrow. Repeat in both
pistons.
9
75
8
15
18 17
72
75
A
C
A
B
AB
B
A
C
C
A
72
1
25
30
12
8
31A
31
13
24
25 30A
72
2
18
18
17
17
18
17
18
17
4
11
11
70
67
66 66
14
67
19
19
59
59
49
9
10
49
20
74 75
2019
59
20
59
20
19
19
19
13
12
7
B
A
74

KEYS
MODE/RESET: For selecting desired function. Hold
down the key for 4 seconds and all values are reset
to zero.
FUNCTIONS
• SCAN: Automatically scan functions of time,count,
total count and calories. Each function will be displayed
for 6 seconds.
• TIME: automatically accumulates the training time
when exercising.
• COUNT: Automatically accumulates the steps of
training when exercising.
• TOTAL COUNT: Automatically accumulates the Total
number of steps made during different training
sessions.
• CALORIES: Automatically accumulates calories
burnt when exercising.
The monitor will turn on automatically if it detects
activity on the machine. If it detects no activity for 4
minutes, the monitor will turn off automatically.
If you detect any abnormality in the monitor, replace
the battery for a better result. The computer uses
one LR44 button battery (1.5v).
BATTERY REPLACEMENT (Battery included)
1. Remove the calorie counter from the main body
front cover part.
2. Take out the battery.
3. Replace the battery with a new one. Make sure
the battery is inserted with the polarities in the
correct directions.
4. Put the calorie counter back in the front cover of
the main body.
-If the monitor doesn´t display clearly or only partial
segments appear, remove the battery and wait fifteen
seconds before reinstalling.
-The batteries life is approximately 3 months under
normal use.
-When the battery is removed, all function values return
to zero.
BATTERY CAUTION & DISPOSAL INFORMATION
1. For best results, use battery type LR44 (DC1.5V).
2. Install only new batteries of the same type in your
product.
3. Failure to insert batteries in the correct polarity, as
indicate in the battery compartment, may shorten
the life of the batteries or cause batteries to leak.
4. Do not mix old and new batteries.
5. Do not mix Alkaline, Standard (carbon-zinc) or
Rechargeable (nickel cadmium) or (Nickel Metal
Hydride) batteries.
6. Do not dispose off batteries in fire.
7. Batteries should be recycled or disposed of as per
state and local guidelines.
ELECTRONIC FITNESS MONITOR

1. Grab the right fixed handle with your right hand.
3. Climb and grab the left upper handle with your
left hand.
WARNING: PROPER POSITIONING
Avoid these positions for your own safety, do not
pull back too much or you may fall with the unit.
Keep your face away from the product to avoid
hit it accidentally.
2. Without letting go the fixed handle, put your right
leg over the right pedal.
4. Finally put your left foot over the left pedal. Then
put your right hand over the upper right handle.
Start your exercise!
HOW TO MOUNT THE UNIT

1. Pull out the knob (25) of the base tube.
2. Loosen and pull the knob (25) from each side of
the position A, release both cylinders (34) and
move them into the cylinder bracket, then secure
them with the knobs (25).
HOW TO STORAGE
3. Fold up the base tubes, be careful to not pinch
your fingers at the middle of the foldable tubes.
4. Insert the knob (25) taken from the base tubes at
the back of the front support tube in order to secure
position.
THIS PRODUCT IS FOR HOME USE ONLY, NOT SUITABLE TO BE USED IN PROFESSIONAL OR HEALTH
FACILITIES OF ANY KIND.
CLAIMS ARE NOT ACCEPTED FOR PRODUCTS THAT HAVE THE FOLLOWING DETAILS.
• Hits.
• Falls.
• Misuse.
• Improper installation or assembly; excessive, commercial and / or professional use of the product.
• Damage caused by oxidation, sulphation, humidity, exposure to rain and / or water or excessive heat sources,
use of abrasives, corrosion.
• Damages caused by the adaptation of parts and / or accesories that do not belong to the product.

The use of this equipment will provide several ben-
efits, improve your physical condition and muscle
tone and combined with a controlled diet, will help
you lose weight.
1. THE WARM UP PHASE
This stage helps get the blood flowing around the
body and the muscles working properly. It will also
reduce the risk of cramp and muscle injury. It is
advisable to do a few stretching exercises as shown
below. Each stretch should be held for approximately
30 seconds, do not force or jerk your muscles into a
stretch - if it hurts, STOP.
2. THE EXERCISE PHASE
This stage requires a greater degree of effort.
After a while, your leg muscles will be more flexible.
Maintain a constant exercise rhythm. The pace of the
exercise should be such that the heart rate remains
within the gray area of the graphic shown below.
This stage should last for a minimum of 12 minutes
though most people start at about 15-20 minutes.
3. THE COOL DOWN PHASE
At this stage, the cardiovascular system and muscles
must relax. Slow down and continue for 5 minutes.
Stretching exercises should be repeated, remembering
not to force the muscles.
As users become more athletic, you may need to
train harder and longer times. It is suggested to
train at least three times a week.
MUSCLE TONING
To tone your muscles while you are on the equipment,
you will need to increase your resistance. This will
strain muscles involved and you may not handle
training the time you would like. If you want to improve
your fitness you need to alternate your training plan.
You should train naturally while warming up and
cooling down, but towards the end of training you
should increase resistance making your legs work
more intensively.
You may have to reduce speed to keep your heart
rate within the target zone.
WEIGHT LOSS
The important factor here is to increase the effort
you put into the exercise. Stronger, lasting far as the
workout, the more calories you burn. Is the same as
when training to improve your fitness, the difference
is the goal.
RECOMMENDED EXERCISES

MAXICLIMBER® XL LIMITED WARRANTY ONE (1) YEAR (VALID ONLY FOR PURCHASES IN USA AND ITS TERRITORIES)
Warranty: Inova US (“Inova”) warrants to the original MaxiClimber® XL purchaser (“Customer”), and only to the
Customer, that the MaxiClimber® XL (“Product”) for which the Customer received this warranty was designed,
developed, manufactured and/or assembled using all due reasonable commercial care and good manufacturing
practices. Inova US Product shall be, when properly assembled and used, free from defects in material and
workmanship and fit for the ordinary purpose for which such Product is used for one (1) year from original date
of purchase. Inova’s sole obligation under this warranty is to repair or replace the Product, at Inova’s option.
Inova’s obligations to the buyer hereunder shall be conditioned upon the buyer’s notifying Inova of the claimed
defect within thirty (30) days of the discovery thereof and upon the Product: (I) being returned, freight prepaid;
(II) being found defective; (III) being found to have been properly assembled and used (if assembled and/or
used); and (IV) being returned within one (1) year from the date of sale to the buyer.
Warranty and Liability Disclaimer: INOVA MAKES NO OTHER WARRANTIES OR REPRESENTATIONS OF ANY
KIND WHATSOEVER, EXPRESS OR IMPLIED, EXCEPT THAT OF TITLE, AND ALL IMPLIED WARRANTIES
INCLUDING ANY WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY
DISCLAIMED. Notwithstanding the foregoing, the duration of any implied warranty or condition of merchantability,
fitness for a particular purpose, or otherwise, on the Product that may be found to be made shall be limited to
the duration of the express warranty set forth above. In no event shall Inova be liable for any loss, inconvenience,
damage, or personal injury, whether direct, incidental, consequential or otherwise, resulting from breach of
any express or implied warranty or condition of merchantability, fitness for a particular purpose or otherwise
with respect to the Product, or from use of the Product, except as set forth herein. Some states or countries do
not allow limitation on how long an implied warranty lasts and some do not allow exclusions or limitations of
incidental or consequential damages, so the above limitations or exclusions may not apply to you. This warranty
gives you specific legal rights, and you may have other rights which may vary from location to location. This
warranty will be interpreted pursuant to the laws of the United States and the State of Florida. The original
English version (meaning) of this warranty controls over all translations; Inova is not responsible for any errors
in translation of this warranty and/or any Product instructions. This warranty is not intended to confer any
additional legal, jurisdictional or warranty rights to you other than those set forth herein or required by law. If
any portion of this warranty is held to be invalid or unenforceable for any reason, such finding will not invalidate
any other provision.
Warranty Service Options: For service under this warranty you must notify Inova in writing within 30 days to
obtain a Returned Merchandise Authorization (RMA). When requesting your RMA, you must specify the Product
in question by providing the order number.
TO OBTAIN ASSISTANCE in USA and its territories contact MaxiClimber® XL Customer Care Center:
Phone: [phone]
Email: [email protected]
Website: www.maxiclimber.com
Any insurance and/or shipping costs incurred in returning your Product under the approved Returned Material
warranty option are your responsibility. Inova will not be responsible for any products lost or damaged in shipment.
Warranty Exclusions: Representatives and brokers of Inova products and services are not authorized to modify
this warranty in any way. It is the Customer’s responsibility to examine the Product regularly to determine the
need for normal service or replacement. This warranty does not cover the following:
• Products that have been modified, neglected or poorly maintained, misused, abused, or involved in accidents
or natural disasters;
• Damage occurring during shipment of the Product (such claims must be presented directly to the freight
forwarder or shipping company);
• Damage to the Product resulting from improper maintenance or repair, the use or installation of parts and/or
accessories that are not compatible with the original intended use of the Product, or the failure to follow the
Product warnings and usage instructions or by anyone weighting more than 300 lb (136 kg);
• Any products for which the Customer does not follow the warranty procedures outlined
above.
Warranty for other Countries/Territories see attached sheet.
BEFORE RETURNING THIS PRODUCT TO THE STORE
We will be happy to correct any problem that you may have or to answer any of your questions regarding
the purchase of this product. Please contact us at our Toll-Free Customer Service Line [phone]
You may also e-mail us at [email protected] or
visit our web site at maxiclimber.com
Thank you!