Insignia NS-MBTK35 User manual

PACKAGE CONTENTS
• Bluetooth receiver
• 3.5 mm audio cable (3 ft.)
• 3.5 mm male-to-male adapter
• 3.5 mm to RCA adapter
• Velcro mounting pads
• Micros USB charging cable
• Carrying pouch
• Quick Setup Guide
FEATURES
Before using your new product, please read these instructions to prevent any damage.
QUICK SETUP GUIDE
NS-MBTK35/NS-MBTK35-C
1Reverse/Volume down
2Multi-function button (MFB): Power on/o,
pairing, play, pause, call
3Skip/Volume up
4LED indicator
5Micro USB charging port
6Audio jack
7Microphone
CHARGING THE RECEIVER
Fully charge the Bluetooth receiver before you use it for the rst
time. When the red LED starts to blink during use, it indicates the
battery is low and requires charging.
1 Plug the micro USB plug of the USB cable into the micro USB port
on your Bluetooth receiver.
2Plug the USB end of the cable into an active USB port, or any USB
charger. A steady red LED indicates it is charging.
3Disconnect the receiver from the USB cable when the red LED
indicator turns o. It may take up to three hours to fully charge.
USING BLUETOOTH
To get started, you need to pair the Bluetooth receiver with
your phone or device.
1
With the receiver turned o, press and hold the MFB for
seven seconds. The LED ashes and the receiver enters
pairing mode.
2
Activate the phone’s Bluetooth function and search for
your receiver. Click on the product name “NS-MBTK35” to
connect. See the instructions that came with your
Bluetooth device for information about pairing.
3
If you are asked for a password, enter “0000”. When pairing
is complete, the LED lights solid blue and a tone sounds.
RECONNECTING TO A PAIRED DEVICE
1Every time the receiver is turned on, it will connect to the
last connected device automatically. If you want to pair
with another device, turn o the Bluetooth function of the
connected device, and repeat the pairing procedure above
for the new device.
2If a device does not automatically reconnect, you may
need to reselect NS-MBTK35 on your Bluetooth device.
3If the receiver is not paired to a Bluetooth device for three
minutes, it will turn o automatically.
USING YOUR RECEIVER
1Press and hold the MFB for two seconds to turn on your
receiver. The LED lights solid blue when it is connected to
your Bluetooth device.
2When the receiver is turned on, press and hold the MFB
for two seconds to turn o the receiver
.
LISTENING TO MUSIC
1To play/pause audio, press the MFB once.
2To increase the volume, press once.
3To reduce the volume, press once.
4To skip to next track, press and hold .
5To skip to previous track, press and hold .
MAKING PHONE CALL
1To make a call, use your phone’s controls, then select the
receiver as the audio source.
2To answer an incoming call, press the MFB .
3To reject an incoming call, press and hold the MFB .
4To end a call, press the MFB once.
Right Left
Bottom
Front
Portable Bluetooth®
Audio Receiver

AUX
English V1 16-0391
1 2 3 4 5 6
FCC Statement:
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment o and on, the user is
encouraged to try to correct the interference by one or more of
the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit dierent
from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for
help.
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
Caution: Changes or modications not expressly approved by
the party responsible for compliance could void the user's
authority to operate the equipment.
Industry Canada Compliance
IC Statement
This device complies with Industry Canada’s licence-exempt RSSs.
Operation is subject to the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference
that may cause undesired operation of the device.
Conformité à Industrie Canada
Déclaration d'IC
Le présent appareil est conforme aux CNR d'Industrie Canada
applicables aux appareils radio exempts de licence. L'exploitation
est autorisée aux deux conditions suivantes :
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d'en
compromettre le fonctionnement.
AUX
USING YOUR WIRED HEADPHONE OR EARPHONE,
RECEIVER WITH STEREO OR RECEIVER IN THE CAR
TROUBLESHOOTING
PROBLEM
No sound or low volume
Cannot connect with
Bluetooth
Bluetooth device keeps
unpairing
“NS-MBTK35” does not
appear on my Bluetooth
device
No power
SOLUTION
• Turn up the volume on your receiver and Bluetooth
device.
• Make sure that your Bluetooth device is not muted.
• Make sure that your receiver and Bluetooth device
are not paired to other devices.
• Make sure that your Bluetooth device is turned on,
Bluetooth is turned on, and “NS-MBTK35” is
selected.
• Shorten the distance between your receiver and the
Bluetooth device.
• Turn your devices o, then on. Re-pair your receiver
and Bluetooth device.
• Make sure that your receiver and Bluetooth device
are not paired to other devices.
• Make sure that your Bluetooth device supports the
HSP, HFP, A2DP, or AVRCP Bluetooth protocol.
• Shorten the distance between your receiver and
your Bluetooth device.
• Recharge your receiver and the Bluetooth device's
batteries.
• Shorten the distance between your receiver and the
Bluetooth device.
• Put your receiver into pairing mode, then refresh
your list of Bluetooth devices. For more information,
see the documentation that came with your
Bluetooth device.
• Make sure that your Bluetooth receiver is charged.
• Make sure that your Bluetooth receiver is turned ON.
La operación de este equipo está sujeta a las siguientes dos condiciones:
1) es posible que este equipo o dispositivo no cause interferencia
perjudicial y
2) este equipo debe aceptar cualquier interferencia, incluyendo la
que pueda causar su propia operación no deseada.
ONEYEAR LIMITED WARRANTY
Visit www.insigniaproducts.com for details.
CONTACT INSIGNIA:
For customer service, call 877-467-4289 (U.S. and Canada) or
01-800-926-3000 (Mexico)
www.insigniaproducts.com
INSIGNIA is a trademark of Best Buy and its aliated companies.
Registered in some countries. Distributed by Best Buy Purchasing, LLC,
7601 Penn Ave South, Richeld, MN 55423 U.S.A.
©2016 Best Buy. All rights reserved. Made in China
OR
3.5mm audio cable
3.5mm audio cable
3.5mm audio cable
attached to headphones
Source
Receiver
Using your smartphone as the audio source, you can connect a variety of sound
devices through your Bluetooth receiver, such as headphones, a stereo receiver,
or a car audio system.
3.5mm
audio
jack