Instant Desks 8408 User manual

Thanks for purchasing one of our products.
Please read carefully the assembly instructions before the installation.
Do not discard this manual or any of the packaging material until the
unit has been completely assembled.
ASSEMBLY INSTRUCTIONS
MODEL-8408


A

C DB
F GE H
JI K L
PONM
TSR
Q
XWV
U
  




Small
Large
Right
Left

Large
Small Small Large
Small

Large



PART QTY. ITEM
1 42Pcs Wooden Pin
Cam Lock &
Bolt Sets
34Sets
2
3 26Pcs Hole Covers
48Pcs Screw - 3.5 x 16mm
58Pcs Screw - 5 x 8mm
(Euro Screw)
68Pcs Screw TP 10#x1/2''
712Pcs Screw - 4 x 38mm
Door Hinge Set
(Both parts come
joined together)
2Sets
8
10 12Pcs Plactic Feet
Handle L Shape
(84mm)
M3.6x22mm Screw
3Sets
11
94Pcs Metal Pin
ab
12 2Sets Sliders
Sets
Right
Left
a
b
a
b
PART QTY. ITEM

HOW TO ASSEMBLE PARTS USING CAM BOLTS AND CAM
M
LOCKS.
HO
W
T
O

O
ASSEM
S
USING
C
BO
S
D C
O
O
CKS.
O


This is not an assembly step; it is a guide for when you are



Th
Th
is
is
n
o
t
a
n
asse
mb
l
y
s
tep;
i
t
is a
g
u
i
d
e
f
o
r
w
h
e
n
y
ou
a
r
e
actually doing the assembly using this kind of hardware.
Cam Bolt Cam Lock
1. Screw the bolt into
the corresponding
panel.
2. insert the cam lock in the
hole of the other panel
making sure it is aligned to
engage with the bolt, then
join both panels. ALIGNMENT
DIRECTION
3. The panels might have a
very small gap which is
normal; turn the cam lock
clockwise to lock the parts
together and the gap will
also close.
4 4

1
Install 42pcs of Wooden Pins (1) into all panels as shown. Use a wooden or light rubber
hammer to avoid damage to the pins. Please pay close attention to which holes you have
to use, and do not join any parts yet!
1
2
Attach all the bolts (2) to panels (A), (B), (C), (D), (N), (O), (J) & (K) as shown above.
Then Attach Metal Pin (9) to panels (C), & (D) as shown above.
J
K
D
B
C
A
N
O
H
H
E
JL
M
K
C
F
D
B
Q
P
T
S

3
4
D
C
- Install the at shaped sliders (12) on panels (C) and (D) using screws (5) as shown.
Flat Shaped
"L" Shaped
Separate the 8 pieces of the sliders (12) according to their shape:
- The at shaped will be used in the next step (4 pieces, both left and right).
- The “L” shaped will be used until step 15 (4 pieces, left and right).
The back end of the
panels have the grove
(Top)
(Front)
(Front)

5
6
- Assemble the leg panels (J) to (L) and (K) to (M) using Cam locks and bolts (2) as shown
and as explained in Page 4.
- First assemble the bottom panel (E) to the left panel (B) using cam locks (2) as
shown and explained in page 4, then install the leg panels (H) to the left panel (B)
as shown.
H
(Top)
(Bottom)
(Top)
(Bottom)

7
8
Assemble the middle panel (D) to the bottom panel (E) using screws (7)
as shown
Assemble the partition panel (F) to the middle panel (D) using cam
locks (2) as shown and explained in page 4.
- PAY ATTENTION TO THE
ORIENTATION OF THE PANEL:
SMOOTH SURFACE FACES TO THE TOP,
SURFACE WITH THE HOLES FACES TO
THE BOTTOM.
(Top)
(Top)
(Bottom)
(Bottom)

9
10
Assemble the right panel (C) to the bottom panel (E) and the partition
panel (F) using cam locks (2) as shown and explained in page 4.
Insert the back panels (W) and (X) into the groves of the panels (B),
(C), (D) and (E) as shown.
C
W
X

11
12
Assemble the main panel (A) to the panels (B), (C)
And (D) using cam locks (2) as shown and explained in page 4.
A
Assemble panel (J) ,(L) ,(M) , & (K) with Cam Lock (2) as shown above. Then attach the
plastic feet (10) to the bottom of all panels in their corners and in the middle of panels (H)
as shown.

13
Using cam locks (2), and as shown and explained in page 4, assemble:
- The large drawer side panels (S) and (T) to the large drawer front panel (N).
- The small drawer side panels (P) and (Q) to the small drawer front panel (O).
Then insert the drawer bottom panels (V) in the groves of all panels on each drawer
as shown.
Assemble the drawers back panels (R) and (U) to their respective drawers
using screws (7) as shown.
R
U
Q
P
O
V
T
N
S
V
2
7

15
16
Place the drawers upside-down and assemble the “L” shaped
sliders to the bottom using screws (4) as shown.
Please note that the wheels go towards the back of the drawers
and the sliders should not protrude from the bottom, otherwise
the drawers raise 3/4” and will not t in the unit.
- Install Handle set (11) to both drawers, Then attach Hole Covers (3) to both drawer side panels
(P) , (Q) , (S) & (T) as shown above.
11
3

I
I
17
18
- Install Handle Sets (11) to door (I) , then install Hinges (8) with screw (6) as shown above.
- Assemble the door (I) to the desk
using screws (6) as shown and
adjust the alignment if necessary:
(A): These screws adjust the vertical alignment.
(B): This screws adjusts the horizontal alignment.
(C): This screws adjusts the depth.

N
O
G
19
- Place both drawers and the Adjust Panel (G) into the cabinet as shown, then attach
Hole Covers (3)
DONE! Before you start using, please read all the warnings in the next page.
Enjoy your new unit!

Do not exceed the weight limits.
Do not expose the surfaces to direct sunlight or to extreme environmental conditions.
Clean the surfaces preferable with a soft cloth damped with a solution of mild soap and water,
then dry with a clean towel.
If you decide to apply a cleaning agent, rst test on a small area of the unit that is hidden from
view, for example, under the keyboard panel.
Do not sit on the tabletop.
Do not allow small children to climb over the unit, play underneath, or reach inside the drawers
and compartments without your supervision.
Before moving the unit within the same room or to an adjacent room:
a) Remove all objects from the tabletop, drawers and shelves that are heavy or might fall o.
b) The unit must be handled by at least 2 persons
c) Use both of your hands and bend your knees, not your backs.
To transport the unit to a location far away from its current location, it is recommended to
properly secure it to avoid breakage during transit.
The warranty does not extend to damages caused by accidents, own errors, incorrect assembly,
negligence, improper use, modications, or not heeding the above warnings.
The warranty is valid only within the continental United States. If you reside in Hawaii, Puerto
Rico, U.S. Dependencies or other countries, please contact the supplier from where the unit was
purchased.
Making any kind of modication to the unit voids the manufacturer’s warranty.
For details on the warranty, please refer to the Warranty Document included with the product,
or visit online:
technimobili.com/pages/techni-mobili-desk-warranty
40Kg (90 Lbs)
4.5Kg (19 Lbs)
4.5Kg (10 Lbs)
4.5Kg (10 Lbs)
4.5Kg (10 Lbs)
4.5Kg (10 Lbs)