Instant Desks IDA-8404 User manual

Thanks for purchasing one of our products.
Please read carefully the assembly instructions before the installation.
Please save this manual for future reference.
ASSEMBLY INSTRUCTIONS
MODEL IDA-8404

51.25"
23.5"
29.5"
34.4"


A B
- Tabletop ▪
▪ Middle Panel
FG
▪ Partition Panel
H
▪ Bottom Panel
C
▪ Left Panel
D
▪ Right Panel
I
-Drawer Front
Panel x 3 ▪Leg Panel
-Drawer Left
Panel x 3
-Drawer Right
Panel x 3
▪Drawer Back
Panel x 3
-Drawer Bottom
Panel x 3 -Back Panel
KLM N
J
E
PART QTY. ITEM
1 28Pcs Wooden Pin
EuroScrew
- 5 x 8mm
12Pcs
412Pcs Screw - 4 x 38mm
2
525Sets
Screw - 3 x 16mm
34Pcs
Cam Bolt and
Lock Set
617Pcs Hole Covers
3Sets Drawer Metal
Sliders Set
7
86Pcs Plastic Feet
9 2Pcs Z Bracket
3Sets
L Shape Handle 84mm
10
11 12Pcs Screw - 3.5 x 15mm
Screw Handle 3.6 x 22mm


HOW TO ASSEMBLE PARTS USING CAM BOLTS AND CAM
M
LOCKS.
HO
W
T
O

O
ASSEM
S
USING
C
BO
S
D C
O
O
CKS.
O


This is not an assembly step; it is a guide for when you are



Th
Th
is
is
n
o
t
a
n
asse
mb
l
y
s
tep;
i
t
is a
g
u
i
d
e
f
o
r
w
h
e
n
y
ou
a
r
e
actually doing the assembly using this kind of hardware.
Cam Bolt Cam Lock
1. Screw the bolt into
the corresponding
panel.
2. insert the cam lock in the
hole of the other panel
making sure it is aligned to
engage with the bolt, then
join both panels. ALIGNMENT
DIRECTION
3. The panels might have a
very small gap which is
normal; turn the cam lock
clockwise to lock the parts
together and the gap will
also close.
4 4
RTA-8404

1
5
B
C
E
1x28
ATTENTION: IN THIS STEP YOU WON'T BE JOINING ANY OF THE PANELS. Insert the wooden pins (1) into the
corresponding holes of panels (B), (C), (D), (E), (F), (G), (J) and (K) as shown. Make sure to insert in the correct
holes as some are intended for other purposes in other steps.
Attach the cam bolts (5) to the corresponding holes on panels (A), (C), (D), (E) and (H) as shown.
Please make sure to insert them in the correct hole as some holes are intended for the wooden
pins in subsequent steps. Please note that on panel (E) the bolts are attached on both sides.
1
2
F
G
I
D
J
K
J
K
J
K
A
LEFT VIEW
RIGHT VIEW
E
E
CD
HH
H

2
E
B
C
Grab the Metal Sliders (7) and group them by their shape (Flat or L shaped). All the L shaped sliders will be
used until step 11, so please set them aside. With the panels (D) and (E) positioned as shown, assemble the
at Sliders using screws (2) as shown. Please note that the wheel goes toward the front of the panel, and
there will be 2 holes above the wheel.
Insert and align the cam locks (5) into the corresponding holes on panel (B), and assemble to it the panels
(C) and (E) as shown and as explained in page 4.
2x12
7x3
5x4
E
D
3
4
7

F
Insert and align the cam locks (5) into the corresponding holes on panels (F) and (G), and assemble them to
(E) as shown and as explained in page 4.
Insert
5
5
6
G
I
N
5x4
E

D
8
-Insert and align the cam locks (5) into the corresponding holes on panels (G) and (F),
and assemble to them the panel (D) as shown and as explained in page 4.
-Attach the Plastic Feet (8) to the bottom of panels (C), (D) and (E) as shown.
8
7
5
C
E
A
C
B
E
D
5x4
8x6
5x7
5
F
G
-Insert and align the cam locks (5) into the corresponding holes on panels (B), (C), (D) and (E),
and assemble the Tabletop (A) as shown and as explained in page 4.

- Attach the Z bracket (9) to the upper corners of the back panel (N) using screws (3). Then Install
the Hole Covers (6) over the cam locks on the places indicated.
9
3x4
6x11
9x2
First insert and align the cam locks (5) in the
drawer side panels (K) and (J), and assemble the
panels to the front panel (H) as shown and as
explained in page 4. Then insert the bottom
panel (M) into the grooves of panels (J), (K) and
(H) as shown.
-Assemble the drawer back panel (L) to the side
panels (J) and (K) using screws (4) as shown.
5
5x2 x4
M
J
K
H
L
11
10
3
9
A
4
4
6
N

-Assemble the L shaped Sliders (7) to the
bottom of the drawer using screws (11) as
shown. NOTE: An incorrect assembly will raise
the drawer 1” and will not t in the desk.
- Install the Handle (10) to the drawer front
panel using its own screws, then cover the
cam lock holes on panel (J) and (K) with (6) as
shown. REPEAT STEPS 10-13 FOR THE OTHER 2
DRAWERS.
7
7
10
11
11
12 13
10
10
7x1
11 x4
6x2
10 x1
6
14
H
H
H
- Insert the drawers into the cabinet starting with the bottom, then
middle, and nally the top one.