Instant Desks IDA-8211 User manual

Thanks for purchasing one of our products.
Please read carefully the assembly instructions before the installation.
Do not discard this manual or any of the packaging material until the unit
has been completely assembled.
MODEL IDA-8211

P.2
x2 Sets

9
11
12
3
3
13
14
16 18
19
20
17
23
24
26
29
28
P.3
10

P.4
A
B
D
C
E
6X40 MM
3X15 MM
4X35 MM
4X20 MM
4X14 MM
16
26
8
4
12
PARTQTY. ITEM PARTQTY. ITEM
F6X12 MM
4
G4X4 MM4
J
6X35 MM
K
5
1
L
36X30 MM
5X40 MM
M
6
N
6X25 MM
SCREWDRIVER
GROMMET
WASHER
20
H
2
I
Φ5X17 MM
2
4

P.5

P.6
1
2
3
3
1
2
5
1
2
6

Holes for
scanner sllder
Holes for
top drawer
Holes for
bottom drawer
8
10
9
88
X2 X2
8
FRONTFRONT
Use screws (B) to assemble the flat drawer sliders (8)
on the middle and bottom sets of slider holes as indicated.
The wheels will be facing towards the front of the panels.
P.7
3
7
8
8

910
4
4
13 20
1515 X4X4
9
10
13
N
12
10
13
910
4
4
6
IMPORTANT: Make sure you use in this step the correct sliders (4) which are longer and have more holes than the sliders (22).
Use screws (B) to assemble the scanner sliders (4) to the top sets of slider holes on panels (9) and (10) in the following order:
First open the slider slowly until the first hole on the front of the slider is visible thru the big opening,
and attach to the front hole on the panels as shown.
Then open the slider completely and attach to the 2 back holes as shown.
Place the drawers’ box bottom panel (13) and the CPU box bottom panel (20) upside-down,
and attach the studs (15) as shown.
4
6X40 MM
A
FRONT
FRONT
2
L
6X25 MM
FRONT
BACK
Attach the bolts (L) to the drawers’ box bottom panel (13),
then assemble the back panel (12) as shown.
Then attach the grommet (N) to the back panel (12).
Back of panel
(13)has 2 holes
for next step.
Attach the bolts (A) to the drawers’ box bottom panel (13),
then assemble the Left and Right panels (9) and (10) as shown.
P.8

10 12
11
11
4
9
10
14
11 12
13
14
FRONT
BACK
K
5X40 MM
Secure the back panel (12) to the side panels (9)
and (10) using screws (K) as shown.
FRONT
4
6X40 MM
A
Attach the bolts (A) to the drawers’ box top panel (14),
and then assemble it the side panels (9) and (10) as shown.
4
Slide out the sliders (4) and assemble the scanner panel (11) using screws (B) as shown.
FRONTFRONT
TOP
TOP
P.9

15
16 18
20 18 16
19
N
18 19
16
16
18
21
18
FRONT
Back of panel (20)
has 2 holes for
next step.
4
6X40 MM
A
First attach the bolts (A) to the drawers’ box
bottom panel (20), then assemble the CPU Left
and Right panels (16) and (18) as shown.
2
L
6X25 MM
FRONT
BACK
Attach the bolts (L) to the CPU box bottom panel (20),
then assemble the back panel (19) as shown.
Then attach the grommet (N) to the back panel (19).
17
Use Screws K to fix the
Cpu’ box Back Panel(19)
to the Cpu’box Right Panel(18).
Attach the bolts (A) to the CPU box top panel (21),
and assemble it to the side panels (16) and (18) as shown.
P.10

19
20 21
FRONT
FRONT
7
25 X4
22
Left
Right
22
24
25 X4
P.11

24
26
26
22
23
FRONT
P.12
Screw Bolts L into the holes of the back face of the Tabletop(24). Please washers(I) over the holes of
panels(14)&(21),and place the tabletop over the frame .Use screws H to fix the Supporting
Tubes(26) to the structure. Finally, tighten the cam locks.

29
29
28
24
25
26
P.13

17
M
27
DONE! Before you start using the unit, please read all the warnings in the following page.
3
3
P.14

P.15