Instant Desks IDA-7050 User manual

ASSEMBLY INSTRUTIONS
P.1 P.1
Thanks for purchasing one of our products.
please read carefully the assembly instructions before the installation.
Please save this manual for future reference.
MODEL IDA-7050
MODEL IDA-7050

P.2 P.2
P R O D U C T D IME N S IO N S :
P R O D U C T D IME N S IO N S :

P.3 P.3
PA R T S L I S T ( P a r t n u m ber , D e s c r ipti o n, Q ty ) :
PA R T S L I S T ( P a r t n u m ber , D e s c r ipti o n, Q ty ) :
1. L eft C a bine t T o p P a ne l ,
1 p c
5. L eft C a bine t R ig ht S ide
P a n e l,1 p c
9. L eft S ide
P a n e l,1 p c
R ig h t C a b ine t
13. B a c k
P a n el,1 p c
R ig ht C a bine t
17. D r a we r B a c k P a n el,
2 p c s
2. L eft C a bine t m id dle P a n e l
,1 p c
6. L eft C a bine t B ottom
P a ne l,1 p c
10. R ig h t S ide
P a n el,1 p c
R ig h t C a b ine t
14. D ra wer F r o nt P a n e l,
2 p c s
18. D ra wer B ottom P a n el,
2 p c s
3. L e f t C a b i n et S u ppor t
P a n e l,2p c s
7. R igh t C a b i n et T o p P a ne l,
1 p c
11 . Mi dd le
L eft S id e P a n e l,1 p c
R ig h t C a bin et
15. D ra wer L e ft S ide P a n e l,
2 p c s
1 9. S l ide r s ,2 s e ts
( ea c h s e t i s f o r 1 d r a we r)
4. L e f t C a b i n et L e ft S ide
P a n e l,1 p c
8. C a bi ne t B o ttom
P a n e l,1 p c
R ig ht
12. M iddle
R igh t S i d e P a ne l,1 p c
R ig h t C a b ine t
16. ,
2 p c s
Dr a wer R ight S i d e P a n e l
You will find on each set 4
pcs:2 flat and 2 L-shaped

P.4 P.4
PA R T S L IS T ( P a r t nu m be r , D e s c r i pti on , Q ty ):
PA R T S L IS T ( P a r t nu m be r , D e s c r i pti on , Q ty ):
H O W T O A S S E MB L E P A R T S U S IN G C A M B O LT S A N D C A M L O C K S :
H O W T O A S S E MB L E P A R T S U S IN G C A M B O LT S A N D C A M L O C K S :
M6x35
Φ8x30
26
34
16
St7x58
St3.5x14 8
St3x14 16
10
8
Φ25
Φ22

P.5 P.5
S T E P 1 :
S T E P 2 :
A S S E MB LY S T E P S :
A S S E MB LY S T E P S :
First insert the wooden pins (B) into the corresponding holes on panels(1) as shown, then
assemble the panels(3) to (1) using cam bolts/locks(A) as shown and as explained in page
4.
First insert the wooden pins (B) into the corresponding holes on the panel(5) as shown,
then assemble the panels(2) to (1) using cam bolts/locks(A) as shown and as explained in
page 4.

P.6 P.6
S T E P 3 :
S T E P 4 :
First insert the wooden pins (B) into the corresponding holes on panels(1) and (3)as shown
, then assemble them to the panels (2) and (5) using cam bolts/locks(A) as shown and as
explained in page 4.
First insert the wooden pins (B) into the corresponding holes on panels(1) as shown, then
assemble the panel (4) to (1) using cam bolts/locks(A) as shown and as explained in page
4.Finally, Using screws (C),assemble the panel(2) to panels(3) as shown.

P.7 P.7
S T E P 5 :
S T E P 6 :
First insert the wooden pins (B) into the corresponding holes on panels(4) and (5)as shown
, then Using screws (C),assemble the panel(6) to panels(4) and (5) as shown.
First, Pasting Wool Feet (F) into the panel(6),then pasting the stickers (G) into the
corresponding the panels(5) and (3).

P.8 P.8
S T E P 7 : S T E P 8 :
S T E P 9 :
Separate the sliders (19) according to their
shapes: The "L" shaped sliders (DL, DR) will
be used until step 15, please set them aside.
The flat sliders (CL, CR) are the ones being
used in step 8.
Assemble the sliders (CL) and (CR) to the
panels (9) and (11),and to the panels (12)
and (10) using screws (E) as shown. Please
pay attention to the orientation of the parts.
First insert the wooden pins (B) into the corresponding holes on panels(7) as shown, then
assemble the panel (9),(11),(12) and (10) to (7) using cam bolts/locks(A) as shown and as
explained in page 4.

P.9 P.9
S T E P 1 0:
Insert the panels (13) in between the panels (9) and (10) as shown.,
S T E P 11 :
First insert the wooden pins (B) into the corresponding holes on the panels (9),(11),(12)
and (10)as shown, then Using screws (C),assemble the panel(8) to panels(9),(11),(12) and
(10) as shown.

P.10 P.10
S T E P 1 2:
Pasting Wool Feet (F) on the the panel(8).
Turn over then cabinet.
S T E P 1 3: S T E P 1 4:
Using screws(D),assemble the Back panel
(17) to the panels (16) and (15) as shown.
Assemble the the panel(14) to the panels(16)
and(17) using cam bolts/locks(A) as shown
and as explained in page 4.

P.11
S T E P 1 5:
Assemble the L shaped sliders (19-DL) and
(19-DR) to the bottom of the drawers using
screws (E) as shown. Please note the
orientation of the sliders; the rollers go at
the back of the drawers, and they touch the
wood on the bottom and the side.
S T E P 1 6:
P.11
Insert the drawers to the cabinet as shown.
The TV stand can be stretched and closed.

C A R E , M A IN T E N A N C E A N D WA R N I N G S :
C A R E , M A IN T E N A N C E A N D WA R N I N G S :
P.12 P.12