Intel PSB-701LF User manual

USER’S
MANUAL
PSB-701LF
Intel®Core2Duo/Quad
FullSizeCPUCard
WithVGA/Sound/2LAN
PSB-701LF M1

Copyright Notice
PSB-701LF Intel® Core 2
Duo/Quad
Full Size CPU Card
With VGA/ Sound/ 2LAN
OPERATION MANUAL
COPYRIGHT NOTICE
This operation manual is meant to assist both Embedded Computer
manufacturers and end users in installing and setting up the system. The
information contained in this document is subject to change without any
notice.
This manual is copyrighted in March, 2008. You may not reproduce or
transmit in any form or by any means, electronic, or mechanical, including
photocopying and recording.
ACKNOWLEDGEMENTS
All trademarks and registered trademarks mentioned herein are the
property of their respective owners.
CE NOTICE
This is a class A product. In a domestic environment this product may
cause radio interference in which case the user may be required to take
adequate measures.

Copyright Notice
FCC NOTICE
This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
You are cautioned that any change or modifications to the equipment not
expressly approve by the party responsible for compliance could void
your authority to operate such equipment.

Contents
TABLE OF CONTENTS
CHAPTER 1 INTRODUCTION
1-1 About This Manual ........................................................ 1-2
1-2 System Specification ...................................................... 1-3
1-3 Safety Precautions ......................................................... 1-5
CHAPTER 2 HARDWARE CONFIGURATION
2-1 Jumper & Connector Quick Reference Table ................ 2-2
2-2 Component Locations .................................................... 2-3
2-3 How to Set the Jumpers ................................................. 2-4
2-4 COM Port Connector ……..…………………………... 2-6
2-5 RS232/422/485(COM2) Selection ................................ 2-7
2-6 Keyboard and PS/2 Mouse Connector .....................….. 2-8
2-7 Keyboard or PS/2 Mouse Selection …………………… 2-8
2-8 External Keyboard Connector ………………………… 2-9
2-9 Reset Connector ............................................................ 2-9
2-10 Hard Disk Drive LED Connector .................................. 2-9
2-11 ATX Power Button ….................................................... 2-10
2-12 External Speaker Connector .......................................... 2-10
2-13 Power LED Connector ……............................................ 2-10
2-14 KeyLock Connector ..………………………………… 2-11
2-15 External SMI Connector ……………………………… 2-11
2-16 Clear CMOS Data Selection ………………………… 2-12
2-17 CPU Fan Connector ………………………………….. 2-12
2-18 System Fan Connector ………………………………… 2-13
2-19 Inverter Connector …………………………..……….. 2-13
2-20 Printer Connector ……………………………………… 2-14
2-21 TPM Connector ………………………….…………….. 2-15
2-22 VGA Connector …………………..…………………… 2-16
2-23 Serial ATA Connector ………………………………… 2-17
2-24 Universal Serial Bus Connector ……………………… 2-19
2-25 LAN Connector …………….………………………… 2-21
2-26 ATX Power Connector ………………………………. 2-23
2-27 Memory Installation ………………………………….. 2-23
2-28 Sound Connector ……………………………………… 2-24
2-29 CD Audio-In Connector ………………………………. 2-24
2-30 LVDS Connector ……………………………………… 2-25
2-31 LVDS Panel Voltage Selection ……………………….. 2-26
2-32 PCI Express/ SDVO Interface Selection ……………… 2-27

Contents
CHAPTER 3 SOFTWARE UTILITIES
3-1 Introduction …………..........................................…....... 3-2
3-2 VGA Driver Utility ……………………………….…… 3-3
3-3 Flash BIOS Update ..............................................…....... 3-4
3-4 LAN Driver Utility …...........................................…...... 3-6
3-5 Sound Driver Utility …………………………………… 3-7
3-6 Intel Chipset Software Installation Utility …..……..….. 3-8
3-7 USB2.0 Software Installation Utility ………………….. 3-9
3-8 Watchdog Timer Configuration ……………………….. 3-10
CHAPTER 4 AWARD BIOS SETUP
4-1 Introduction ................................................................... 4-2
4-2 Entering Setup ............................................................... 4-3
4-3 The Standard CMOS Features ………............................ 4-4
4-4 The Advanced BIOS Features ....................................... 4-7
4-5 Advanced Chipset Features ........................................... 4-9
4-6 Integrated Peripherals …............................................... 4-12
4-7 Power Management Setup ............................................. 4-16
4-9 PC Health Status …….................................................... 4-19
4-10 Load Fail-Safe Defaults ................................................. 4-18
4-11 Load Optimized Defaults .........................................…. 4-18
4-12 Password Setting ……………………………………… 4-19
4-13 Save & Exit Setup ......................................................... 4-20
4-14 Exit Without Saving ………………………………… 4-21
APPENDIX A EXPANSION BUS
SHB Connector Pin Assignment ……………………………… A-2
APPENDIX B TECHNICAL SUMMARY
Block Diagram ........................................................................... B-2
Interrupt Map ............................................................................ B-3
RTC & CMOS RAM Map ........................................................ B-4
Timer & DMA Channels Map .................................................. B-5
I/O & Memory Map ...............................................…................ B-6

Page:1-1
INTRODUCTION
This chapter gives you the information for PSB-701LF. It also
outlines the System specifications.
Section includes:
zAbout This Manual
zSystem Specifications
zSafety Precautions
Experienced users can skip to chapter 2 on page 2-1
for a Quick Start.
CHAPTER
1

Chapter 1 Introduction
Page: 1-2 PSB-701LF USER
′ S MANUAL
1-1. ABOUT THIS MANUAL
Thank you for purchasing our PSB-701LF Intel® Core 2 Duo/ Core 2
Quad Full Size CPU Card enhanced with VGA/Sound/2LAN, which is
fully PC / AT compatible. The PSB-701LF provides faster processing
speed, greater expandability and can handle more tasks than before. This
manual is designed to assist you how to install and set up the system. It
contains four chapters. The user can apply this manual for configuration
according to the following chapters:
Chapter 1 Introduction
This chapter introduces you to the background of this manual, and the
specifications for this system. The final page of this chapter will indicate
how to avoid damaging this board.
Chapter 2 Hardware Configuration
This chapter outlines the component locations and their functions. In the
end of this chapter, you will learn how to set jumper and how to configure
this card to meet your own needs.
Chapter 3 Software Utilities
This chapter contains helpful information for proper installations of the
VGA utility, LAN utility, Sound utility, and Flash BIOS Update. It also
describes the Watchdog-timer configuration.
Chapter 4 Award BIOS Setup
This chapter indicates you how to set up the BIOS configurations.
Appendix A Expansion Bus
This Appendix introduces you the expansion bus for SHB connector.
Appendix B Technical Summary
This section gives you the information about the Technical maps.

Chapter 1 Introduction
PSB-701LF USER ′ S MANUAL Page: 1-3
1-2. SYSTEM SPECIFICATIONS
zCPU (LGA775):
Intel® Core 2 Quad/ Core 2 Duo/ Celeron M with LGA775 CPU socket.
(Support Process Technology of Intel: 65nm, 45nm).
Auto detect voltage regulator.
zCHIPSET :
Intel® Q35 + ICH9DO + FWH (FSB:800/1066/1333MHz).
zMEMORY :
2×240Pin 667/800MHz DDR2-DIMM.
If want to enable the iAMT function, please plug the DDR2 memory in the
DIMM1.
zCACHE :
Built-in CPU.
zREAL-TIME CLOCK :
Build in South Bridge.
zBIOS :
Phoenix-Award BIOS for plug & play function.
32 Mb flash with VGA BIOS.
Support S/IO Setup.
zKEYBOARD CONNECTOR :
PS/2 K/B, with mini DIN or external connector (1×5-pin Boxheader) with
mini DIN cable; Support Y-Cable.
zMOUSE CONNECTOR :
PS/2 Mouse, with mini DIN connector (selectable with KB DIN connector).
zDISPLAY :
Build-in Intel® Q35; Support CRT, LVDS.
LVDS: Support 18-bit, 24-bit LVDS. Use Chrontel CH7308A by
SDVO bus to transfer to LVDS.

Chapter 1 Introduction
Page: 1-4 PSB-701LF USER
′ S MANUAL
zSATA INTERFACE :
6 ports S-ATA. Support RAID 0,1,5,10.
4 connectors are on SHB and 2 ports signals be linked to gold fingers.
zSERIAL PORT :
2 port, 16550 UARTs RS-232.
COM1 for RS-232,COM2 for RS-232/422/485.
zPARALLEL PORT :
One port supports SPP / ECP / EPP Function.
zUSB CONNECTOR :
10 port, support USB 2.0.
6 connectors are on SHB and 4 ports signals be linked to gold fingers.
zLAN ADAPTER :
Dual Ports to support 100/1000Mbps with Intel® 82566DM, Intel® 82573L.
Support Wake-on-LAN wtih ATX power
zSOUND :
High Definition Audio with Realtek ALC262 IC.
zHARDWARE MONITORING FUNCTION :
Monitor Voltage, CPU temperature, & Cooling fan.
If CPU Temperature is over setting, the buzzer will send out a warming (only
under DOS system).
zGREEN FUNCTION :
Controlled by hardware and software.
zLED INDICATOR :
System power
Hard Disk access
zDMA CONTROLLER :
82C37 x 2
zDMA CHANNELS :
7

Chapter 1 Introduction
PSB-701LF USER ′ S MANUAL Page: 1-5
zINTERRUPT CONTROLLERS :
82C59 x 2
zINTERRUPT LEVELS :
15
zOPERATING TEMPERATURE :
0 to 60°C.
zINPUT POWER REQUIREMENT :
ATX power: +5V, +12V, -12V, 5VSB.
zBOARD DIMENSIONS :
338.5mm x 122mm, 13.33” x 4.8”
zBOARD NET WEIGHT :
370 gram. (0.82lb)
1-3. SAFETY PRECAUTIONS
Follow the messages below to avoid your systems from damage:
1. Keep your system away from static electricity on all occasions.
2. Prevent electric shock. Don‘t touch any components of this card when the
card is power-on. Always disconnect power when the system is not in use.
3. Disconnect power when you change any hardware devices. For instance,
when you connect a jumper or install any cards, a surge of power may
damage the electronic components or the whole system.

Page 2-1
HARDWARE
CONFIGURATION
** QUICK START **
CHAPTER
2
Helpful information describes the jumper & connector settings, and
component locations.
Section includes:
zJumper & Connector Quick Reference Table
zComponent Locations
zConfiguration and Jumper settings
zConnector’s Pin Assignments

Chapter 2 Hardware Configuration
Page: 2-2 PSB-701LF USER
′ S MANUAL
2-1. JUMPER & CONNECTOR QUICK REFERENCE TABLE
COM Port Connector ....................…..................……… COM1, COM2
RS232/422/485 (COM2) Selection .....................……… JP10
Keyboard/ PS/2 Mouse Connector …………………….. DIN1
Keyboard/ PS/2 Mouse Selection ……………………… JP9
External Keyboard Connector …………………………. EXKB1
Reset Connector …......................…….................…… JP7 (5, 7)
Hard Disk Drive LED Connector …....................……… JP7 (1, 3)
ATX Power Button …………………………………….. JP7 (6, 8)
External Speaker Connector ….…….....................…… JP7 (14, 16, 18, 20)
PLED Connector …………….…….……............…… JP7 (2, 4)
KeyLock Connector …………………………………… JP7 (13, 15)
External SMI Connector ……………..…………..……. JP7 (17, 19)
Clear CMOS Data Selection …………………………… JP3
CPU Fan Connector …………………………………… CPU_FAN1
System Fan Connector ………………………………… SYS_FAN1
Inverter Connector …………………………………….. INV1
Printer Connector ……………………………………… LPT1
TPM Connector ………………………………………. JP12
VGA Connector ……………………………………….. VGA1
Serial ATA Connector …………………………………. SATA1, SATA2, SATA3, SATA4
Universal Serial Bus Connector …….....................…… USB1, USB2, USB3
LAN Connector ……………………………………… LAN1, LAN2
ATX Power Connector ………………………………… ATX_PWR1
Memory Installation ..................................…......……… DIMM1, DIMM2
Sound Connector ………………………….…………… AUDIO1
CD Audio-In Connector ……………………………….. CD_IN1
LVDS Connector ………………………………………. LVDS1
LVDS Voltage Selection ………………………………. JP2
PCI Express / SDVO Interface Selection ……………… JP1, JP5
Reserved Pin …………………………………………… JP4

Chapter 2 Hardware Configuration
PSB-701LF USER ′ S MANUAL Page: 2-3
2-2. COMPONENT LOCATIONS
PSB-701LF Connector, Jumper and Component locations

Chapter 2 Hardware Configuration
Page: 2-4 PSB-701LF USER
′ S MANUAL
2-3. HOW TO SET THE JUMPERS
You can configure your board by setting jumpers. Jumper is consists of
two or three metal pins with a plastic base mounted on the card, and by
using a small plastic "cap", Also known as the jumper cap (with a metal
contact inside), you are able to connect the pins. So you can set-up your
hardware configuration by "open"or "close"pins.
The jumper can be combined into sets that called jumper blocks. When
the jumpers are all in the block, you have to put them together to set up
the hardware configuration. The figure below shows how this looks like.
JUMPERS AND CAPS
If a jumper has three pins (for examples, labelled PIN1, PIN2, and PIN3),
You can connect PIN1 & PIN2 to create one setting by shorting. You can
either connect PIN2 & PIN3 to create another setting. The same jumper
diagrams are applied all through this manual. The figure below shows
what the manual diagrams look and what they represent.

Chapter 2 Hardware Configuration
PSB-701LF USER ′ S MANUAL Page: 2-5
JUMPER DIAGRAMS
2 pin Jumper
looks like this
Jumper Cap
looks like this
3 pin Jumper
looks like this
Jumper Block
looks like this
JUMPER SETTINGS
Looks like this
3 pin Jumper
2-3 pin close(enabled)
Looks like this
Jumper Block
1-2 pin close(enabled)
2 pin Jumper close(enabled)
1
1
1212
1
1
Looks like this

Chapter 2 Hardware Configuration
Page: 2-6 PSB-701LF USER
′ S MANUAL
2-4. COM PORT CONNECTOR
COM1 : COM1 Connector
COM1 is fixed as RS-232.
The pin assignment is as follows :
PIN ASSIGNMENT
1 COM1_DCD#
2 COM1_RX
3 COM1_TX
4 COM1_DTR#
5 GND
6 COM1_DSR#
7 COM1_RTS#
8 COM1_CTS#
9 COM1_RI#
COM2 : COM2 Connector
The COM2 is selectable as RS-232/422/485.
The pin assignment is as follows :
ASSIGNMENT
PIN RS-232 RS-422 RS-485
1 COM2_DCD# TX- TX-
2 COM2_RX TX+ TX+
3 COM2_TX RX+ RX+
4 COM2_DTR# RX- RX-
5 GND GND GND
6 COM2_DSR# RTS- GND
7 COM2_RTS# RTS+ GND
8 COM2_CTS# CTS+ GND
9 COM2_RI# CTS- GND

Chapter 2 Hardware Configuration
PSB-701LF USER ′ S MANUAL Page: 2-7
2-5. RS232/422/485 (COM2) SELECTION
JP10 : RS-232/422/485 (COM2) Selection
This connector is used to set the COM2 function.
The jumper settings are as follows :
COM 2
Function Jumper Settings (pin closed) Jumper Illustrations
RS-232 All Open
RS-422 1-2, 3-4, 9-10
RS-485 1-2, 5-6, 7-8
*** Manufacturing default -- RS-232.

Chapter 2 Hardware Configuration
Page: 2-8 PSB-701LF USER
′ S MANUAL
2-6. KEYBOARD AND PS/2 MOUSE CONNECTOR
DIN1 : Keyboard or PS/2 Mouse Connector
DIN connector can support keyboard, Y-cable, or PS/2 Mouse, user may
select the right device to used on “Keyboard or PS/2 Mouse Selection”.
The pin assignments are as follows :
ASSIGNMENT
PIN Keyboard PS/2 Mouse
1 KBDATA MSDATA
2 MSDATA MSDATA
3 GND GND
4 5VSB 5VSB
5 KBCLK MSCLK
6 MSCLK MSCLK
2-7. KEYBOARD OR PS/2 MOUSE SELECTION
JP9 : Keyboard or PS/2 Mouse Selection
For Y-Cable user, please set the jumper same as AT keyboard.
The jumper settings are as follows:
DEVICE TYPE JUMPER SETTING
(pin closed) JUMPER
ILLUSTRATION
AT KEYBOARD 3-5
4-6
PS/2 MOUSE 1-3
2-4
*** Manufactory default -- AT Keyboard

Chapter 2 Hardware Configuration
PSB-701LF USER ′ S MANUAL Page: 2-9
2-8. EXTERNAL KEYBOARD CONNECTOR
EXKB1 : External Keyboard Connector
The pin assignment is as follows :
PIN ASSIGNMENT
1 5VSB
2 GND
3 NC
4 KBDATA
5 KBCLK
2-9. RESET CONNECTOR
JP7 (5, 7) : Reset Connector.
The pin assignment is as follows :
PIN ASSIGNMENT
5 GND
7 RST_BTN
2-10. HARD DISK DRIVE LED CONNECTOR
JP7 (1, 3) : Hard Disk Drive LED Connector
The pin assignment is as follows :
PIN ASSIGNMENT
1 HD_LED+
3 HD_LED-

Chapter 2 Hardware Configuration
Page: 2-10 PSB-701LF USER
′ S MANUAL
2-11. ATX POWER BUTTON
JP7 (6, 8) : ATX Power Button
The pin assignment is as follows :
PIN ASSIGNMENT
6 PWRBTNSW
8 GND
2-12. EXTERNAL SPEAKER CONNECTOR
JP7 (14, 16, 18, 20) : External Speaker Connector
The pin assignment is as follows :
PIN ASSIGNMENT
14 SPK_VCC
16 SPEAKER SIGNAL
18 SPEAKER SIGNAL
20 SPEAKER SIGNAL
2-13. POWER LED CONNECTOR
JP7 (2, 4) : Power LED Connector
The pin assignment is as follows:
PIN ASSIGNMENT
2 PW_LED+
4 PW_LED-