Intel R2000BB series User manual

Thank you for buying an Intel® Server System. The following information will help you
assemble your Intel®Server System and install components.
If you are not familiar with ESD [Electrostatic Discharge] procedures used during
system integration, see the complete ESD procedures described in your Service Guide.
This guide and other supporting documents are located on the web at:
http://www.intel.com/support.
G48801-002
Intel® Server System R2000BB Family
Quick Installation User's Guide
* 2.5" hard drive bay system as shown

( This page is intentionally left blank. )

i
Table of Contents
General Installation Process ........................................................................................................ 2
Reference ............................................................................................................................................ 11
System Overview .............................................................................................................................. 1
Preparing the System ....................................................................................................... 2
Remove the Top Cover ..................................................................................................... 2
Remove the Air Duct ......................................................................................................... 2
Remove Processor Heatsink(s) ................................................................................... 2
Install the Processor(s) ................................................................................................... 3
Install Processor Heatsink(s) ........................................................................................ 4
Install Memory Modules ................................................................................................... 4
Install Hard Drives .............................................................................................................. 5
Install Optical Drive ............................................................................................................ 7
Install the Air Duct .............................................................................................................. 7
Remove Add-in Card Riser Assembly ....................................................................... 7
Install Add-in Card(s) ......................................................................................................... 7
Install Add-in Card Riser Assembly ........................................................................... 8
Install Rack Handles .......................................................................................................... 8
Install Intel® I/O Expansion Module (optional) ..................................................... 8
Install Intel® RAID C600 Upgrade Key (optional) ............................................... 8
Install Intel® RAID Smart Battery (optional) ......................................................... 8
Install Intel® Remote Management Module 4 (optional) ................................ 9
Install Second Power Supply Module (optional) ................................................. 9
Install Bezel (optional) ...................................................................................................... 9
Install the Top Cover ......................................................................................................... 9
Finishing Up ......................................................................................................................... 10
Software ............................................................................................................................... 10

ii
Warning
Read all caution and safety
statements in this document
before performing any of the
instructions. Also see the Intel
®
Server Board and Server Chassis
Safety Information document at:
http://www.intel.com/support/
motherboards/server/sb/cs-010770
.htm for complete safety information.
Warning
Installation and service
of this product to be
performed only by
qualified service personnel
to avoid risk of injury from
electrical shock or energy
hazard.
Caution
Observe normal ESD
[Electrostatic Discharge]
procedures during system
integration to avoid possible
damage to server board and/or
other components.
Tools Required
Anti-static
wrist strap
Phillips*
screwdriver
Intel is a registered trademark of Intel Corporation or its subsidiaries in the United States and other countries. *Other names and brands may be claimed as the
property of others. Copyright © 2012, Intel Corporation. All rights reserved.
Thermal Operation and Configuration Requirements
To keep the system operating within supported maximum thermal limits, the system must meet the following operating and
configuration guidelines:
• Ambient in-let temperature cannot exceed 35ºC and should not remain at this maximum level for long periods of time.
Doing so may affect long term reliability of the system.
• The CPU-1 processor + CPU heatsink must be installed first. The CPU-2 heatsink must be installed at all times, with
or without a processor installed.
• Memory Slot population requirements:
NOTE: Specified memory slots either can be populated with a DIMM or supplied DIMM Blank (DIMM blanks are only
provided in systems that require them). Memory population rules apply when installing DIMMs.
▪ DIMM Population Rules on CPU-1
Install DIMMs in order; Channels A, B, and C. Start with 1st DIMM slot (blue) on each channel, then 2nd slot.
▪ DIMM Population on CPU-2
Install DIMMs in order; Channels D, E, and F. Start with 1st DIMM slot (blue) on each channel, then 2nd slot.
• All hard drive bays must be populated. Hard drive carriers either can be populated with a hard drive or supplied
drive blank.
• The air duct must be installed at all times.
• In single power supply configurations, the second power supply bay must have the supplied filler blank installed at
all times.
• The system top-cover must be installed at all times.

1
System Overview
Intel® Server System R2000BB Family
Useful Information:
• The system must be configured with two CPUs to enable PCIe slot 1 (Top) and PCIe slot 2 (middle) on Riser #2.
• The mini-SAS connector labeled SCU_1 requires an 8-port SATA/SAS Intel® RAID C600 Upgrade Key to be functional.
• DIMM channels D-F can only be used in dual processor configurations.
• The CPU-2 heat sink must be installed with or without a processor installed.
System Features and Components
Hot Swap
Hard Drive Bays
System Fans
CPU2
CPU2
Memory Slots
CPU1
Memory Slots
CPU1
PCI Riser #2
Power Supply
#1
Server Board
Air Duct
Optical Drive Bay
Front Control Panel
PCI Riser #1
Power Supply
#2
* 2.5" Hard Drive Bay system as shown

Minimum Hardware Requirements
•Memory Type:
Minimum of one 512MB DDR3 1066/1333/1600 MHz UDIMM or one
1GB DDR3 1066/1333/1600 MHz RDIMM.
•Processor:
Intel® Xeon® processor E5-2400 product family.
•Hard Disk Drives: SATA
For a complete list of compatible processors, heatsinks, and memory, see
http://www.intel.com/support.
To avoid integration difficulties and possible board damage, your system must
meet the following minimum requirements:
2
General Installation Process
The installation instructions in this section are for common components of Intel® Server System
R2000BB family.
1
Preparing the System
Observe normal ESD (Electrostatic Discharge)
procedures.
Place your Intel®Server System on a flat anti-static
surface to perform the following integration procedures.
Observe ESD procedures before reaching inside to make
server board connections or install components.
A
B
B
2
Remove the Top Cover
B
Remove the four screws.
Slide cover back and lift upward.
A
IMPORTANT!
Before proceeding
further, check your
Intel®Server System
for disconnected or
loose cables and
components that
may have occurred
during shipping.
B
A
3
Remove the Air Duct
Carefully push in the two latches on the air duct.
A
Rotate the back edge of the air
duct up to disengage the two
tabs from fan bulkhead.
B
4
Remove Processor Heatsink(s)
The heatsink is attached to the server board / processor socket with captive fasteners.
Lift the heatsink straight up.
A
B
C
CAUTION: The heatsink has thermal interface material (TIM) on the underside
of it. Use caution so that you do not damage the thermal interface material.
Use gloves to avoid sharp edges.
Using a #2 Phillips* screwdriver, loosen the four screws located on the
heatsink corners in a diagonal manner using the following procedure:
Using a #2 Phillips* screwdriver, start with screw 1 and loosen it by
giving it two rotations and stop. (IMPORTANT: Do not fully loosen.)
Proceed to screw 2 and loosen it by giving it two rotations and stop.
Similarly, loosen screws 3 and 4.
Repeat steps A and B by giving each screw two rotations each time
until all screws are loosened.
TIM
2
3
1
4
Chassis Front
A
B
C

3
General Installation Process
A
B
NO CPU
B
A
NO CPU
5Install the Processor(s)
Cautions:
1. When opening a socket,
DO NOT TOUCH the gold
socket wires.
A. Open the
Socket Lever
Rotate the lever open
all the way.
B. Open the
Load Plate
Open the load plate
as shown.
Push the lever handle
down and away from the
socket to release it.
A
B
Push the rear tab with your
finger tip to bring the front
end of the load plate
up slightly.
A
B
C. Remove the Processor
Protective Cover
2. When unpacking a
processor, hold only by the
edges to avoid touching the
gold contacts.
A
Take the processor
out of the box and
remove the protective
shipping cover.
A
Save the
protective
cover.
C
D
Orientation Posts
Orientation Notches
A
Install the Processor(s) ... continued
E. Close Load Plate and Socket Lever
Close the socket lever and ensure that
the load plate tab engages under the
socket lever when fully closed.
With your finger, push down on the
load plate lever as shown.
D
AA
C
D. Install the Processor
CAUTION: The underside
of the processor has
components that may damage
the socket wires if installed
improperly.
DO NOT DROP processor
into the socket!
Processor must align
correctly with the socket
opening before installation.
Components
Orient the processor with
the socket so that the
orientation notches on the
processor align with the
two orientation posts on
the socket.
A
Install the processor as shown.
Press the protective
cover to remove it from
the load plate.
B
B
Close the load plate all
the way as shown.

4
General Installation Process
7Install Memory Modules
DDR3 DIMM Memory Identification:
Other
Memory
DDR3
CAUTION: Observe normal ESD (ElectroStatic
Discharge) procedures to avoid possible damage to
system components.
DIMM notch and socket bump must align as shown below.
CPU1 SocketCPU2 Socket
DIMM_D1 DIMM_D2 DIMM_E1 DIMM_E2 DIMM_F1 DIMM_F2 DIMM_A1 DIMM_A2 DIMM_B1 DIMM_B2 DIMM_C1 DIMM_C2
Install Memory Modules ... Continued
Memory Configurations and Population Order:
C
AIRFLOW
Chassis Front
2
3
1
4
A
B
TIM
D
CAUTION:
Do not
over-tighten
fasteners.
E
6Install Processor Heatsink(s)
NOTE: Heatsink styles may vary.
Remove the protective film on the TIM if present.
D
CAUTION: The heatsink has thermal interface
material (TIM) on the underside of it. Use caution so
that you do not damage the thermal interface material.
Use gloves to avoid sharp edges.
E
C
A
BAlign heatsink fins to the front and back of
the chassis for correct airflow.
Airflow goes from front-to-back of chassis.
Each heatsink has four captive fasteners and
should be tightened in a diagonal manner using
the following procedure:
Using a #2 Phillips* screwdriver,
start with screw 1 and engage screw
threads by giving it two rotations
and stop. (Do not fully tighten.)
Proceed to screw 2 and engage screw
threads by giving it two rotations and
stop. Similarly, engage screws 3 and 4.
Repeat steps C and D by giving each
screw two rotations each time until
each screw is lightly tightened up to
a maximum of 8 inch-lbs torque.
Intel® Server Board S2400BB
For best performance, a minimum of three DIMMs per CPU is recommended, populated in the blue slot of each memory channel.
In a single-processor configuration, always populate A1 DIMM first.
In a dual-processor configuration, always populate A1 DIMM first for CPU 1 and D1 DIMM first for CPU2.
NOTE: For additional memory configurations, see the Service Guide on the Intel®Server Deployment & Management DVD that accompanied your Intel®
Server System, or go to http://www.intel.com/support.
Memory sizing and configuration is supported only for qualified DIMMs approved by Intel. For a list of supported memory, go to
http://serverconfigurator.intel.com.

5
General Installation Process
Install Memory Modules ... Continued
To Install DIMMs:
Open both DIMM socket levers.
C
A
D
E
Note location of alignment notch.
B
CAUTION: Avoid touching contacts
when handling or installing DIMMs.
A
C
DB
E
IMPORTANT! Visually check that each latch is fully closed and correctly engaged with
each DIMM edge slot.
Push down firmly on the DIMM until it snaps into place and both levers close.
Insert DIMM making sure the connector edge of the DIMM aligns correctly with the slot.
8Install
Hard Drives
2.5" Hard Drive Carrier (For system with 2.5" hard drive bay only)
Hard Drive Numbering Diagram
Drive 0 Primary 24 x 2.5" hard drive bay as shown
A
A
B
Press the green latch to
unlock.
Pull out the black lever and slide
the carrier out.
B
D
C
Remove the four screws securing the plastic drive blank,
from the 2.5" HDD carrier.
Disengage and remove the plastic drive blank from the
HDD carrier.
C
D
Install the hard disk drive using the four screws as shown.
Make Sure the connector end of the drive matches the
backplane connector.
E
F
With the lever open, insert the hard disk drive
assembly into the chassis, then push in the lever
to lock it into place.
F
CAUTION: If you don't install
all drives, empty drive bays
must be occupied by carriers
with plastic drive blank
provided to maintain proper
system cooling.
2.5" HDD
E
0123456 7 89 10 11 12 13 14 15 16 17 18 19 20 21 22 23

6
General Installation Process
0
1
2
3
4
5
6
7
8
9
10
11
2.5" HDD
d3
Install Hard Drives ... Continued
3.5" Hard Drive Carrier (For system with 3.5" hard drive bay only)
Hard Drive Numbering Diagram
Drive 0 Primary
A
B
TOP
BREAK OFF TAB
BEFORE MOUTING
2.5´´ HARD DRIVE
A
B
Remove the drive carrier by pressing the green button
and opening the lever.
d1 d4
E
F
d2 d3
Slide the carrier out.
TOP
BREAK OFF TAB
BEFORE MOUTING
2.5´´ HARD DRIVE
C
C
Remove the four screws securing the
plastic drive blank and remove the
plastic drive blank.
Install the plastic drive blankfrom
top. Secure the bracket with three
screws as shown.
Slide the 2.5" HDD into the plastic
drive blank to align the screw holes
with the right and left rail.
Break off the tab on the
plastic drive blank.
Install 2.5" Hard Drive as option:
Secure the hard disk drive using
the four screws for 2.5" HDD.
3.5´´ HDD
D
D
Install the hard disk drive using the same
four screws as shown. Make sure the
connector end of the drive matches the
backplane connector.
With the lever open, insert the hard disk drive assembly into
the chassis.
Push in the lever to lock it into place.
d1
Bottom
View
TOP
BREAK OFF TAB
BEFORE MOUTING
2.5´´ HARD DRIVE
d2
FE
12 x 3.5’’ hard drive bay as shown
8 x 3.5’’ hard drive bay as shown
CAUTION: If you don't install
all drives, empty drive bays
must be occupied by carriers
with plastic drive blank
provided to maintain proper
system cooling.
0
1
2
3
4
5
6
7
d4
2.5" HDD

7
General Installation Process
9Install Optical Drive
AB
IMPORTANT NOTE: If you do not
install a device at this location,
install the optical device bay filler
panel shown below. This is
required to maintain proper
system cooling.
Rear View
of Optical
Drive
A
Install the plastic guide onto the back
of the drive and attach with two screws
as shown.
Insert the optical drive into chassis opening
and push all the way until it stops.
CConnect the cables as
shown.
Optical
Device
Assembly
B
Data
Power
Optical
Drive
A
A
B
C
10 Install the Air Duct
Use care to avoid pinching system cables.
Lower front edge of the air duct to engage the two tabs
on the fan bulkhead.
A
Carefully push in the two latches on the air duct.
B
Push down the air duct into place.
C
Riser Card
Connector
11 Remove Add-in Card
Riser Assembly
Grasp the riser assembly with both hands
and pull up to remove from system.
CAUTION:
Place the riser
assembly upside down
to avoid damage to the
riser card connector.
12 Install Add-in Card(s)
•Full-height PCIe Card Shown
Riser Connector
REMOVE Filler Panel
A
B
Add-in Card
C
A
A
B
C
CAUTION:
Observe normal ESD precautions
when installing add-in cards.
Remove the filler panel from the add-in card slot and
remove the screw as shown.
Insert add-in card until it seats in the riser connector.
Secure add-in card with screw as shown.
NOTE: Make sure that all empty add-in card slots have
filler panels installed.
NOTE: Add-in card install sequence for low-profile add-in
cards is the same.

8
General Installation Process
14 Install Rack Handles
NOTE: Rack handles are required to install
the bezel. For detailed instructions, see the
product Service Guide available on the Intel®
Server Deployment & Management DVD.
16 Install Intel® RAID C600
Upgrade Key (optional)
Locate the white 4-pin key header next to Riser Slot 1.
Carefully pickup the Intel® RAID C600 Upgrade Key.
Match the Key and connector orientation and press
down to install.
STOR_UPG_KEY
Hooks (2)
Slots (2)
Add-in Card
D
E
C
B
A
13 Install Add-in Card Riser Assembly
A
Slide back the card guide on the air duct.
B
Pull up the blue plastic pin out of the card guide.
C
Position the riser card edge connector over the server board
riser socket and align the two hooks on the back edge of the
riser assembly with the slots on the back of the chassis, then
press straight down into riser socket.
D
Slide forward the card guide to lock in the back edge of the
add-in card.
E
Insert the blue plastic pin into the card guide to secure the
add-in card.
NOTE:
-Step A, B, D, and Eare only needed when a
full-length PCI card is installed on the riser assembly.
-
Riser Slot 2 is not functional without having two
processors installed.
I/O Connector
I/O Module
A
B
C
D
15 Install Intel® I/O Expansion Module
(optional)
A
D
B
Squeeze the sides of the I/O module
bay filler plate, and pull it away from
the chassis back panel.
Fit the front of the module into the
back panel slot and align the I/O
Module over the three stand-offs.
Secure the module with the three
screws as shown.
C
Carefully press down on the I/O
module to engage connectors.
NOTE: If included, remember to
install the EMI shield.
17 Install Intel® RAID Smart Battery (optional)
ALocate the mounting holes
inside the chassis and
reposition all cables routed
over the fan bulkhead.
Position the battery against
the side wall and through the
opening in the fan bulkhead.
BAlign the tabs on the plastic
battery holder with the
mounting holes in the
chassis and slide the plastic
battery holder toward the
front of the system until the
tabs engage with the
mounting holes.
A
B
Fan Bulkhead

9
General Installation Process
18 Install Intel® Remote Management Module 4 (optional)
ALocate the RMM4 Lite connector close to the Riser Slot 2, carefully
pickup the Intel®RMM4 Lite module, match the alignment pin of the
module and the connector on server board, then press to install.
Installing the Intel® RMM4 Lite
Push out and remove the metal cover on the chassis where the NIC RJ-45
receptacle will align.
A
Position the module over the server board, fit the front of the module into
the back panel slot, then attach the module to the server board connector.
B
Secure the module with the two screws as shown.
C
Installing the Intel® RMM4 NIC
RMM4 Lite
Connector
A
AF005068
Chassis Back
Opening
Filler
A
B
C
Finger Hole
A
B
19 Install Second Power Supply Module (optional)
AB
Use the 'finger hole' to remove the
filler panel.
Insert the power supply module into the power
supply cage and push all the way until it clicks
into place.
Using the handle, pull the module from the
chassis while pressing the green latch in the
direction shown.
Power Supply Removal
B
A
A
Recessed
Edge
21
Install the Top Cover
A
B
Place the top cover on system and slide towards the front of chassis
until the recessed front edge is fully engaged.
Install the three screws at the front and torque to 7-9in-lbs, then
install the screw at the back and torque to 7-9in-lbs.
20
Install Bezel (optional)
A
B
A
B
Lock the right end of the front bezel to the rack handle.
Push in the left side of the bezel until it clicks into place.
NOTE: Before installing the bezel, you must install the rack handles.

10
General Installation Process
23
Software •BIOS, Drivers, and Operating System Installation
B. Configure your RAID Controller:
C. Install your Operating System:
D. Install Operating System Drivers:
A. Update the System Software:
E. Install Intel® System Management Software (optional):
Update the System BIOS, ME Firmware, BMC Firmware, and FRU & SDR data, using the latest versions posted for the system at http://www.intel.com.
If using a RAID card, use the instructions provided with the RAID controller. If using on-board RAID, you must activate RAID in the BIOS setup. See the Intel®Server
System R2000BB Service Guide for more information.
Use the instructions provided with the RAID controller and with the operating system.
With the operating system running, insert the Intel®Server Deployment & Management DVD. If using a Microsoft Windows* operating system, the Express Installer
will autorun and allow you to select the appropriate drivers to install. On other operating systems, browse the DVD folders to locate and install the driver files.
Download the latest version of the Intel®System Management Software from http://www.intel.com/go/servermanagement and use the instructions provided at that link to
install the software.
Note: The FRUSDR utility must be run for full platform management functionality.
* Other brands and names may be claimed as the property of others..
2nd Power
Supply
Module
1st Power
Supply
Module
Serial
Port A
Intel ®RMM4
NIC Port
Intel ®I/O
Module
(optional)
Serial Port B (optional) Add-in Card Slots
Network
Video USB
Ports
NIC 1 NIC 3
NIC 2 NIC 4
22
Finishing Up
1. Verify the system top cover is installed.
2. Install the server into the rack using the instructions provided with the rack
mounting kit.
3. Connect your USB keyboard/mouse, video and other I/O cables/devices
as shown.
Then connect the power cord(s).
CAUTION: This system must be operated with the TOP COVER installed to
ensure proper cooling.
Before installing your operating system, you must finish your system
installation, make I/O connections, and plug in power cord(s).

11
Reference
Front Panel Controls and Indicators Standard Control Panel
HIJ
A B C D E F G
Your system may include one of two front control panel types.The
features of each are as follows:
A. ID Button with integrated LED
B. NMI Button (recessed, tool required)
C. LAN-1 Activity LED
D. LAN-3 Activity LED
E. System Cold Reset Button
F. System Status LED
G. Power Button with integrated LED
H. HDD Activity LED
I. LAN-4 Activity LED
J. LAN-2 Activity LED
G
H
A
E
I
DB
F
J
C
Integrated
BMC
ID LED
Serial Jumper
RMM4
NIC
Riser Slot_2
Riser Slot_1
I/O Expansion
Module
Connector
Serial B
TPM Connector
CPU 2 Socket
HSBP Power
Front Panel USB
Front Panel Video
CPU 1 Socket
USB
Serial A
RMM4 Lite
USB Type A
SCU_0
SCU_1
Video NIC4 NIC3
Status
LED
NIC2 NIC1
Diagnostic
LEDs
mSATA SSD
LP eUSB SSD
Chassis Intrusion
HDD LED
SATA 1
Optional
12V Power 2 Optional
12V Power 1
PDB
Control
PDB Power
LCP
ODD/SSD Power
System
Fan 1
System
Fan 2
System
Fan 3
System
Fan 4
System
Fan 5
System
Fan 6
Front Panel
DIMM_D1 DIMM_D2 DIMM_E1 DIMM_E2 DIMM_F1 DIMM_F2 DIMM_A1 DIMM_A2 DIMM_B1 DIMM_B2 DIMM_C1 DIMM_C2
HSBP_I2C
BMC Force
Update Jumper
IPMB
Battery
Main Power 1
Storage
Upgrade
Key
BIOS Recovery Jumper
ME Force Update Jumper
Password Clear Jumper
BIOS Default Jumper
Intel® Server Board R2000BB Component Layout
See your Intel®Server System R2000BB Service Guide for expanded component and connection information.

12
Reference
A complete list of accessories and spares can be found at: http://www.intel.com/support.
Air Flow
CPU2 SocketCPU1 Socket
FAN 1 FAN 5FAN 2 FAN 3 FAN 4
System Fan Connection
* NOTE: System FAN connector 5 on the server board is not used.
*

13
Reference
8 x 3.5" HSBP
Integrated
BMC
Power
Supply
#1
Power
Supply
#2
Power
Distribution
Board
mSATA
SSD
I2C
Front Panel
Front Panel Video
Front Panel USB
PCIe
RAID
Install into PCIe Riser Card
0
1
B
B
U
Optical Drive
SSD
Mount on air duct
FAN 1 FAN 2 FAN 3 FAN 4 FAN 5
System Cabling Diagram
NOTE: To activate the port SCU1 (4-7) on the server board, a proper Intel®RAID C600 Upgrade Key must be
installed. For instructions, see Intel®RAID C600 Upgrade Key Installation Guide.
For system with 8 x 3.5” hard drive bay:

14
Reference
12 x 3.5" HSBP
Integrated
BMC
Power
Supply
#1
Power
Supply
#2
Power
Distribution
Board
mSATA
SSD
Installed into PCIe Riser Card
SSD
Intel® RAID
Expander Card
RES2SV240
2345
01
I2C
Front Panel
Interposer
Board
PCIe
RAID
0
1
Mount on air duct
Install into PCIe Riser Card
B
B
U
FAN 1 FAN 2 FAN 3 FAN 4 FAN 5
System Cabling Diagram
For system with 12 x 3.5” hard drive bay:
NOTE: To activate the port SCU1 (4-7) on the server board, a proper
Intel®RAID C600 Upgrade Key must be installed. For instructions,
see Intel®RAID C600 Upgrade Key Installation Guide.

15
Reference
Integrated
BMC
Power
Supply
#1
Power
Supply
#2
Power
Distribution
Board
8 x 2.5" HSBP
mSATA
SSD
I2C
Front Panel
Front Panel Video
Front Panel USB
PCIe
RAID
Install into PCIe Riser Card
0
1
B
B
U
Optical Drive
FAN 1 FAN 2 FAN 3 FAN 4 FAN 5
SSD
Mount on air duct
System Cabling Diagram
For system with 8 x 2.5” hard drive bay:
NOTE: To activate the port SCU1 (4-7) on the server board, a proper Intel®RAID C600 Upgrade Key must be
installed. For instructions, see Intel®RAID C600 Upgrade Key Installation Guide.

16
Reference
Integrated
BMC
Power
Supply
#1
Power
Supply
#2
Power
Distribution
Board
8 x 2.5" HSBP8 x 2.5" HSBP
SAS
Expander
A B
C D E
H I
F
G
mSATA
SSD
I2C
I2C
Front Panel
Front Panel Video
Front Panel USB
PCIe
RAID
Install into PCIe Riser Card
0
1
B
B
U
Optical Drive
FAN 1 FAN 2 FAN 3 FAN 4 FAN 5
SSD
Mount on air duct
System Cabling Diagram
For system with 16 x 2.5” hard drive bay:
NOTE: To activate the port SCU1 (4-7) on the server board, a proper
Intel®RAID C600 Upgrade Key must be installed. For instructions,
see Intel®RAID C600 Upgrade Key Installation Guide.