Inter-m EP-6216 User manual

Operation Manual
Emergency Panel
EP-6216
* Rack mount products in the Western Hemisphere(North America, South America,
and the Caribbean) do not have handles installed due to customer preference.

EMERGENCY PANEL
Welcome
Welcome
A personal welcome to you from the management and employees of Inter-M
All of the co-workers here at Inter-M are dedicated to providing excellent products with inherently good value,
and we are delighted you have purchased one of our products.
We sincerely trust this product will provide years of satisfactory service, but if anything is not to your complete
satisfaction, we will endeavor to make things right.
Welcome to Inter-M, and thank you for becoming part of our worldwide extended family!
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK.
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
WARNING
To prevent fire or shock hazard, do not
expose the unit to rain or moisture.
*WARNING FOR YOUR PROTECTION PLEASE READ THE FOLLOWING-WATER AND MOISTURE: Unit should not be used near water(e.g.
near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool, etc). Care should be taken so than objects do
not fall and liquids are not spilled into the enclosure through openings.
*Do not install this equipment in a confined space such as a book case or similar unit.
*This apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such vases, shall be placed on the apparatus.
*This apparatus shall be connected to a mains socket outlet with a protective earthing connection.
* It has heed to be easy to disconnect the device. To disconnect the device from power, separate AC input cable from inlet or unplug the AC Cord.
* The socket-outlet shall be installed near the equipment and shall be easily accessible.
CAUTION
*These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock, do not perform any servicing
other than that contained in the operating instructions unless you are qualified to do so.
NOTE
*This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will
be required to correct the interference at his own expense.
This symbol is intended to alert the user to the
presence of uninsulated “dangerous voltage” within
the product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to
persons.
This symbol is intended to alert the user to the
presence of important operation and maintenance
(servicing) instructions in the literature accompanying
the appliance.
Caution: To prevent electric shock do not use this (polarized) plug with
an extension cord, receptacle or other outlet unless the
blades can be fully inserted to prevent blade exposure.
Attentions: Pour prévenir les chocs électriques ne pas utiliser cette
fiche polarisée avec un prolongateur, une prise de courant
on une autre sortie de courant, sauf si les lames peuvent
étre insérées à fond sans en laisser aucune partie à
découvert.

EMERGENCY PANEL
1
EP-6216
Contents
Contents
Unpacking .......................................................................................................................................2
Installation
Environment....................................................................................................................................2
Important Safety Instructions.............................................................................................................2
Features ...........................................................................................................................................3
Front Panel ......................................................................................................................................4
Rear Panel .......................................................................................................................................5
Suggestions for Rack Installation ..................................................................................................7
Operating Procedure......................................................................................................................7
Voice File Board (VF-01N Option)...............................................................................................8
Applications ....................................................................................................................................9
Block Diagram ..............................................................................................................................10
Specifications ................................................................................................................................11
Service
Procedures....................................................................................................................................13
Schematic.....................................................................................................................................13
Parts List .......................................................................................................................................13
Warranty .......................................................................................................................................13

EMERGENCY PANEL
Unpacking
2EP-6216
Unpacking
Although your EP-6216 is neither complicated nor difficult to operate, we recommend you take a few minutes to
read this brief manual and familiarize yourself with the important information regarding product features, setup
and operation.
As with most electronic devices, we strongly recommend you retain the original packaging. In the unlikely event
the product must be returned for servicing, the original packaging (or reasonable equivalent) is required.
Installation
Installation
Environment
Never place this product in an environment which could alter its performance or reduce its service life. Such
environments usually include high levels of heat, dust, moisture, and vibration.
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide
blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult
an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and
the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus.
When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged in any way, such as power-supply cord or plug is
damaged, liquid has been spilled or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, does not operate normally, or has
been dropped.
S3125A
S3125A

EMERGENCY PANEL
3
EP-6216
Features
Features
- FIRE ALARM
Connect to a fire sensor for a fully functional fire alarm.
- AUTO OPERATING FUNCTION
Alarm will sound automatically on alternate floors.
- AUTO ANNOUNCEMENT
Automatic announcements during fire alarm operation.
- TEST FUNCTION
Use the test function for system tests or to conduct emergency drills.

EMERGENCY PANEL
4EP-6216
Front Panel
Front Panel
1. FIRE INDICATOR
This panel blinks red when fire has been detected.
2. OUTPUT INDICATOR LED
Audio signal level indication.
3. MICROPHONE AND BUILT-IN SPEAKER
The unit contains a built-in uni-directional dynamic microphone, and a built-in speaker for convenient local
monitoring.
4. TEST SWITCH
This switch is used to check system. When the switch is pressed, the relevant LED lights.
5. STANDBY INDICATOR LED
This LED will light to indicate that power has been applied to the unit, and the unit is in Standby mode.
6. MIC VOLUME
This knob controls the mic output volume. Rotating in a clockwise direction increases volume.
12 34
56
FIRE

EMERGENCY PANEL
5
EP-6216
Rear Panel
Rear Panel
1. MATRIX CONNECTOR
This multi-pin EMG jack is for the connection of an external timer, such as the Inter-M ECS-6216P.
2. REMOTE MIC TERMINAL
Connect an external microphone to this terminal. The external mic is active when the Remote Mic Switch (3)
is set to External.
3. REMOTE MIC SWITCH
Connect the Remote Mic switch to this terminal.
4. DC 24V OUT TERMINAL
Automatically output when automatic announcement.
5. AUTO ANN SELECTOR SWITCH
This switch is used to set the auto announcement mode to either external or internal.
6. SIREN VOLUME
This knob controls siren level.
7. PRE-AMP INPUT JACK
This jack is used to connect the output of a pre-amplifier.
8. REMOTE 1, 2 INPUT JACKS
These jacks are used to connect the output of a pre-amplifier to REMOTE 1 and REMOTE 2.

EMERGENCY PANEL
6EP-6216
9. TIMER INPUT JACK
This jack is for the connection of an external timer, such as the Inter-M PW-6242A.
10. AUTO ANN INPUT JACK
Connect the output of an auto broadcasting system (or a cassette deck or other line level device) to this
balanced XLR input jack. This input is active when the AUTO ANN SELECTOR SWITCH (5) is set to external.
11. PRE OUT JACK
This balanced XLR jack carries the pre-amp out signal, and is used to make a mono connection to the main
amplifier and speakers.

EMERGENCY PANEL
7
EP-6216
Suggestions for Rack InstallationSuggestions for Rack Installation
1. Switch off power to the EP-6216 before installing the system.
2. Connect the Inter-M ECS-6216P to the MATRIX CONNECTOR (1) on the rear panel.
3. Connect the PRE OUT jack (11) to the input of your main amplifier.
4. Connect audio output of your auto broadcasting system to the AUTO ANN input jack (10), and the DC 24V
In jack of your auto broadcasting system to the DC 24V OUT jack (4) of the EP-6216.
5. Connect the output jack of the Inter-M PW-6242A to the TIMER jack (9).
6. Connect the output of your remote pre-amp to the REMOTE INPUT jack (8) and the pre-amp of the main
broadcasting system to the PRE-AMP INPUT jack (7).
7. If using a remote mic, connect the microphone and switch to the rear panel REMOTE MIC TERMINAL (2) and
REMOTE MIC SWITCH (3).
Operating ProcedureOperating Procedure
Switch off the EP-6216 Power Switch.
Select either External mode or Internal mode (3) before installing the system.
Using the TEST SWITCH, an alarm is broadcast through the built-in speaker.
Test the microphone, setting the MIC VOLUME on front (6) as desired.
NOTE: The Pre-Amp Input, Remote 1 and 2 Input, Timer Input, and Auto-Ann Input are sent to the PRE OUT in
the following priority.
PRIORITY INPUT SIGNAL
1 Auto-Ann
2 Timer
3 Remote 1
4 Remote 2
5 Pre-Amp
TABLE 1: MATRIX CONNECTOR PIN NO. & FUNCTION

EMERGENCY PANEL
8EP-6216
Voice File Board (VF-01N Option)Voice File Board (VF-01N Option)
1. The board of VF-01N is for the automatic broadcasting in case of emergency.
2. DIP switcher that can set up the number of the repeat output is included in VF-01N board.
- Regard of the number of repeat voice output, please select the switcher as below.
- Basically, the release of the product is configured the 4 times of this.
3. Voice compose board of VF-01N is possible to control the level of output.
During installation, please control the level of output by VR-101 of VF-01N.
Switch Selection
1
ON
OFF
OFF
OFF
2
OFF
ON
OFF
OFF
3
OFF
OFF
ON
OFF
4
OFF
OFF
OFF
ON
Repeat
2 times
4 times
8 times
16 times
DIP-SW
ON
ON
ON
ON
VR101

EMERGENCY PANEL
9
EP-6216
Applications
Applications
DUCK P.PWR
CH1CH2
DUCK P.PWR
CH3CH4CH5CH6CH7CH8CH9
LINE IN
MIC IN
L
RR
L
R
L
2
1
AUX
1
2
PRIORITY
+-
DC INPUT
24V
INSERTREC OUT
MASTER
2
1
SUB OUT
OUTPUT INPUTINPUT
LINE IN
MIC IN
LINE IN
MIC IN
LINE IN
MIC IN
LINE IN
MIC IN
LINE IN
MIC IN
LINE IN
MIC IN
LINE IN
MIC IN
LINE IN
MIC IN
RM1
INPUT
AUDIO
OUT
AUDIO
OUT
RM2
INPUT LINK IN LINKOUT UPGRADE SOURCE1
RS 232
SOURCE 2
EMG PANEL
/
ADDRESS
12345678910
1234 5678
9101112 13 14 15 16
1234 5678
9 101112 13 14 15 16
TERM.
LOAD OPEN
12345678
910111213141516
FIRE
SENSOR
SPEAKER
OUTPUT
AMP
INPUT
HEHCECEHCEHC EEHCEHCEHC HC HCHCHCHC HCHCHCHC
ϊۑ@Ţ۩م@ێԟێ@ۘڽ@Ĉڐ@
Ê۾@ɜ@ট۩ۉ@کێ@ۘںɩ@
࠭ҿșڽ@ّçǦ@ǷҜθ@ϊݖݖ@
ψֲ֫٤N
܆Ͽࠤ@Z@EMERGENCY COMBINATION
SYSTEM
ЂʠϿ@Z ECS 6216P
܄ÿ۾ؖ@Z DC 24V,900mA
܆ܖۜϿ@Z
ďÖݖڜࣶ TEL : [phone]
PD TIMER
EXTCOM
DC 24V
RM1
INPUT
AUDIO
OUT
AUDIO
OUT
RM2
INPUT LINK IN LINKOUT UPGRADE SOURCE1
RS 232
SOURCE 2
EMG PANEL
/
ADDRESS
12345678910
1234 5678
9101112 13 14 15 16
1234 5678
9 101112 13 14 15 16
TERM.
LOAD OPEN
12345678
910111213141516
FIRE
SENSOR
SPEAKER
OUTPUT
AMP
INPUT
HEHCECEHCEHC EEHCEHCEHC HC HCHCHCHC HCHCHCHC
ϊۑ@Ţ۩م@ێԟێ@ۘڽ@Ĉڐ@
Ê۾@ɜ@ট۩ۉ@کێ@ۘںɩ@
࠭ҿșڽ@ّçǦ@ǷҜθ@ϊݖݖ@
ψֲ֫٤N
܆Ͽࠤ@Z@EMERGENCY COMBINATION
SYSTEM
ЂʠϿ@Z ECS 6216P
܄ÿ۾ؖ@Z DC 24V,900mA
܆ܖۜϿ@Z
ďÖݖڜࣶ TEL : [phone]
PD TIMER
EXTCOM
DC 24V
DC OUT
24V
MATRIX
12 0
SIREN/VOLUME
PRE IN REMOTE IN 2 REMOTE IN 1 TIMER IN AUTO ANN IN PRE OUT
CONTROL OUT (TO AUTO ANN)
EXT INT
AUTO. ANN
REMOTE MIC
MIC SW
EXT INT
HPF
ON OFF
~ AC INPUT
220V 60Hz
FUSE : T8AL / 250V
DC INPUT
24V
BALANCED
INPUT
1V/10KΩ
LINK
INPUT(ADJ)
12dB 0dB
100V(20.8Ω)
43.8V(4Ω)
OUTPUT
COM
A
B
70V(10.2Ω)
FRAMEFLOAT
GROUND
LIFT
www.inter-m.com
CH 1
OUTPUT CH 2CH 3CH4CH 5CH 6
INPUT
FUSE
T315mAL/ 250V
~AC INPUT
230V,50Hz
8W
INPUT OUTPUT
INPUT OUTPUT
LINE
LINK
TERM.
OPEN
LOAD
GND.
FLOAT
FRAME
DIRECT BOX
DIB 6000
+
VOL INPUT OUTPUT
POWER
TO PC
MUTE
LEVEL
INPUT
VOL
+
MIC
PRI.
OFF
ON
MAXMIN
LINE
IN OUT VOICEFILE
TERM.
LINK
LOAD OPEN
ADDRESS
12345678910
FIRE SENSOR 12345678COM
COM
9 10111213141516
ϊۑ@Ţ۩م@ێԟێ@ۘڽ@Ĉڐ@Ê۾@ɜ@ট۩ۉ@کێ@ۘںɩ@
࠭ҿșڽ@ّçǦ@ǷҜθ@ϊݖݖ@ψֲ֫٤N
܆ܖۜϿ@Z
ďÖݖڜࣶ TEL : [phone]
܄ÿۖͶ@Z DC 24V,100mA
܆Ͽࠤ@Z@EMERGENCY
ЂʠϿ@Z ER 6116
ROUTER
DC 24V
COMNO NC
RELAY
OUTPUT
IN OUT VOICEFILE
TERM.
LINK
LOAD OPEN
ADDRESS
12345678910
FIRE SENSOR 12345678COM
COM
9 10111213141516
ϊۑ@Ţ۩م@ێԟێ@ۘڽ@Ĉڐ@Ê۾@ɜ@ট۩ۉ@کێ@ۘںɩ@
࠭ҿșڽ@ّçǦ@ǷҜθ@ϊݖݖ@ψֲ֫٤N
܆ܖۜϿ@Z
ďÖݖڜࣶ TEL : [phone]
܄ÿۖͶ@Z DC 24V,100mA
܆Ͽࠤ@Z@EMERGENCY
ЂʠϿ@Z ER 6116
ROUTER
DC 24V
COMNO NC
RELAY
OUTPUT
RM1RM2RM3RM4RM5RM6RM7RM8
INPUT
OUTPUT
ϊۑ@Ţ۩م@ێԟێ@ۘڽ@Ĉڐ@Ê۾@ɜট۩ۉ@کێ@ۘںɩ@
࠭ҿșڽ@ّçǦ@ǷҜθ@ϊݖݖ@ψֲ֫٤N
܆Ͽࠤ@Z@REMOTE MIC EXTENDER
ЂʠϿ@Z RME 6108
܄ÿۖͶ@Z DC 24V,150mA
܆ܖۜϿ@Z
ďÖݖڜࣶ TEL : [phone]
DC 24V
RM1RM2RM3RM4RM5RM6RM7RM8
INPUT
OUTPUT
ϊۑ@Ţ۩م@ێԟێ@ۘڽ@Ĉڐ@Ê۾@ɜট۩ۉ@کێ@ۘںɩ@
࠭ҿșڽ@ّçǦ@ǷҜθ@ϊݖݖ@ψֲ֫٤N
܆Ͽࠤ@Z@REMOTE MIC EXTENDER
ЂʠϿ@Z RME 6108
܄ÿۖͶ@Z DC 24V,150mA
܆ܖۜϿ@Z
ďÖݖڜࣶ TEL : [phone]
DC 24V
SPEAKER
RECEIVER
RME-6108
RME-6108
PW-6242A
PV-6232
PP-6213
EP-6216
(SLIDE S/W: EXT)
ECS-6216P
(MASTER)
ER-6116
ECS-6216S
(SLAVE)
ER-6116
PO-6106
AMPLIFIER
DIB-6000
SOURCE
RM-01
RM-6024+RM-6012KP
RM #1 RM #8
RM #9 RM #16
PC(GUI)

EMERGENCY PANEL
10 EP-6216
Block Diagram
Block Diagram

EMERGENCY PANEL
11
EP-6216
EP-6216
Operating Modes Auto, Test
Emergency Siren Frequency 800Hz (Emergency)
Program Exchange Mode Businessm, RM1, RM2, Timer
Operation Temperature -10°C ~ +40°C / 14°F~104°F
Power Source DC 24V
Power Consumption 4W
Weight (SET) 4kg/8.8lb
Dimensions (SET) 482(W)x88(H)x280(D)mm/19(W)x3.5(H)x11(D)in
* Design and specification are subject to be changed for the improvement of product quality without pre notice.
Specifications
Specifications

EMERGENCY PANEL
12 EP-6216
※ DIMENSIONS
440
28088
482

EMERGENCY PANEL
13
EP-6216
Service
Service
Procedures
Take steps to insure the problem is not related to operator error or other products within the system. Information
provided in the troubleshooting portion of this manual may help with this process. Once it is certain that the
problem is related to the product contact your warranty provider as described in the warranty section of this
manual.
Schematic
A Schematic is available by contacting your warranty provider.
Parts List
A Parts List is available by contacting your warranty provider.
Warranty
Warranty
Warranty terms and conditions vary by country and may not be the same for all products. Terms and conditions
of warranty for a given product may be determined first by locating the appropriate country which the product
was purchased in, then by locating the product type.
To obtain specific warranty information and available service locations contact Inter-M directly or the
authorized Inter-M Distributor for your specific country or region.

MADE IN KOREA
August 2021 154169
Inter-M, Ltd. (Korea) began operations in 1983.
Since then, Inter-M has grown to become one of the largest manufacturers
of professional audio and commercial sound electronics equipment in the world.
Inter-M has gained worldwide recognition for its own branded products,
as well as private label manufacturing of electronics sold under other names (OEM).
The company is no longer just a Korean company, but rather a global company
that is truly international in scope, with factories and offices in Korea and China,
and sales and marketing operations located in Japan, Europe, and the U.S.A.
With more than 850 employees around the globe,
Inter-M is well-poised for further growth and expansion.
Inter-M Americas, INC.
5666 CORPORATE AVE. CYPRESS, CA 90630
TEL : [phone], FAX : [phone]
Home Page : http://www.inter-m.net, E-mail : [email protected]
Inter-M Corporation
SEOUL OFFICE : 719, DOBONG-RO, DOBONG-GU, SEOUL, KOREA
TEL : [phone]~8, FAX : [phone]
Home Page : http://www.inter-m.com, E-mail : [email protected]