Intermatic ET9232 Guide

ET9232 Ethernet Module
Ethernet Module Replacement Instructions
MODEL ET9232
• Turnpoweroffatmainpanelbeforeservicingthisswitchortheequipmentitcontrols.
• Morethanonedisconnectswitchmayberequiredtode-energizetheequipmentbeforeservicing.
WARNING
Keeplow-voltagewiringseparatefromhigh-voltagewiring,includingdeadfrontmaterialbetweenwiringareas.Separate
conduitmaybeusedforlow-voltagewiringifnolinevoltagewiringispresent.
Risk of Fire or Electric Shock
Ethernet Module Replacement Guidelines
There are separate Ethernet Module replacement instructions for the one and two circuit time
switches and the 4 to 16 circuit time switches. Be sure to follow the applicable Ethernet Module
replacement instructions for your ET90000 time switch.
ReplacingEthernetModuleon1or2CircuitTimeSwitch
Follow the instructions below to replace an Ethernet Module on a 1 or 2 circuit ET90000 time switch.
1. Disconnect power to the time switch.
2. Open the time switch enclosure cabinet door.
3. At the bottom of the time switch, disconnect the Ethernet cable from the port in the Ethernet
module plastic enclosure.
4. Disconnect the Ethernet module ribbon cable connector plug from the terminal connector.
5. Remove the rivets that secure the Ethernet Module and remove the module from the plastic insulator.
6. Dispose of the rivets and module.
7. Align the new Ethernet module plastic enclosure over the holes on the plastic insulator and
secure the plastic enclosure with the rivets provided with the new module.
8. Connect the ribbon cable connector plug to the terminal connector.
9. Insert the Ethernet cable into the Ethernet port in the enclosure.
10. Close the time switch enclosure door.
11. Return power to the time switch.
CAUTION Risk of Unintended Equipment Operation
Figure 1. ET90000 with Ethernet Module components shown
Terminal
Connector
Ribbon
Cable
Ethernet
Cable port
Rivet (2)
Ethernet Module
Plastic Enclosure

ReplacingEthernetModuleon4to16CircuitTimeSwitch
Follow the instructions below to replace an Ethernet Module on a 4 to 16 circuit ET90000 time switch.
1. Disconnect power to the time switch.
2. Open the time switch enclosure door.
3. Remove the screws from the deadfront and remove the deadfront from the enclosure. Set aside
the deadfront and screws for re-use.
4. Remove the screw that secures the time switch controller door assembly. Set aside the screw
for re-use.
Deadfront Screws
Deadfront
Figure 2. Removing the deadfront.
Figure 3. Time switch controller door assembly with screw.

5. On the inside of the door assembly, disconnect the Ethernet cable from the module.
6. Disconnect the Ethernet module ribbon cable connector plug from the applicable terminal
connector.
7. Remove the three screws that secure the Ethernet Module and remove the module from inside
of the door assembly. Set aside the screws for re-use.
8. Open the new ET9232 Ethernet module plastic enclosure and remove the board.
9. Discard the plastic enclosure.
10. Remove and discard the ribbon cable from the Ethernet module board.
11. Align the module board over the holes on the door assembly and secure the board with the
screws previously removed in step 7.
12. Connect the ribbon cable connector plug to the applicable terminal connector. See Figure 4.
13. Insert the Ethernet cable into the Ethernet port on the module.
14. Close the door assembly and secure with the screw previously removed in step 4.
15. Return the deadfront to the enclosure and secure with the screws previously removed in step 3.
16. Close the time switch enclosure door.
17. Return power to the time switch.
Figure 4. Removing the Ethernet Module.
Figure 5. Ethernet module plastic enclosure.

158--01118
LIMITED ONE YEAR WARRANTY
If within the warranty period specified, this product fails due to a defect in material or workmanship, Intermatic Incorporated will repair or replace
it, at its sole option, free of charge. This warranty is extended to the original purchaser only and is not transferable. This warranty does not apply
to: (a) damage to units caused by accident, dropping or abuse in handling, acts of God or any negligent use; (b) units which have been subject to
unauthorized repair, opened, taken apart or otherwise modified; (c) units not used in accordance with instructions; (d) damages exceeding the cost of
the product; (e) sealed lamps and/or lamp bulbs, LED’s and batteries; (f) the finish on any portion of the product, such as surface and/or weathering, as
this is considered normal wear and tear; (g) transit damage, initial installation costs, removal costs, or reinstallation costs.
INTERMATIC INCORPORATED WILL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. SOME STATES DO NOT ALLOW THE
EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY
TO YOU. THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS OR IMPLIED WARRANTIES. ALL IMPLIED WARRANTIES, INCLUDING THE
WARRANTY OF MERCHANTABILITY AND THE WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY MODIFIED TO EXIST ONLY
AS CONTAINED IN THIS LIMITED WARRANTY, AND SHALL BE OF THE SAME DURATION AS THE WARRANTY PERIOD STATED ABOVE. SOME
STATES DO NOT ALLOW LIMITATIONS ON THE DURATION OF AN IMPLIED WARRANTY, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU.
This warranty service is available by either (a) returning the product to the dealer from whom the unit was purchased, or (b) completing a warranty claim
on line at www.intermatic.com. This warranty is made by: Intermatic Incorporated, Customer Service 7777 Winn Rd. Spring Grove, Illinois 60081-9698.
For warranty service go to: http://www.intermatic.com or call 815-675-7000.
INTERMATIC INCORPORATED
SPRING GROVE, ILLINOIS 60081
www.intermatic.com