Intermec MobileLAN access 2101 User manual

Intermec’s MobileLAN™access family of access points delivers reliable and seamless wireless performance to almost any operational environment. The MobileLAN access 2101 is designed for standards-based connectivity and it may have up to two of the following radios installed:
•IEEE 802.11b •WLI Forum OpenAir
The 2101 with an IEEE 802.11b radio installed is Wi-Fi certified for interoperability with other 802.11b wireless LAN devices.
This quick start guide helps you to understand the 2101 ports and LEDs.You can also use this quick start guide to learn how to install the 2101, how to connect the 2101 to power and to your network, and how to use the MobileLAN access Utility to configure its IP address. Once you assign the 2101 an IP address, you can continue configuring it using a Web browser interface or a Telnet session.
Out of the Box
MobileLAN™access 2101
Heading 1
About the 2101
Safety First
Quick Start Guide
Specifications
Software Updates
MobileLAN access 2101 Quick Start Guide *069960-004* *069960-004* Physical dimensions 3.8 cm x 16.0 cm x 25.0 cm
(1.49 in x 6.27 in x 9.84 in)
Weight 526 g (1.16 lb) Electrical rating ~100 to 240 V
1.0A 50 to 60 Hz
Operating temperature -20°C to 65°C (-4°F to 149°F) Storage temperature -30°C to 70°C (-22°F to 158°F) Humidity 10 to 90%, non-condensing For more information on using the MobileLAN access 2101, please see the •MobileLAN access System Manual (Part No. 067150). •Intermec Web site at www.intermec.com.
To order access point accessories and antennas, contact your local Intermec representative.
Caution Government regulatory agencies mandate that the antenna not be alterable.Therefore, the access point uses a custom antenna connector. Do not attempt to use a different antenna or you may damage the connector and the access point. Conseil Les agences responsable de la réglementation gouvernementale exigent que l’antenne ne soit pas modifiable. Par conséquent, le point d’accès est doté d’un connecteur d’antenne personnalisé. Ne pas essayer d’utiliser une antenne différente au risque d’endommager le connecteur et le point d’accès.
Caution You must use the appropriate Intermec power supply with these devices or equipment damage may occur. Conseil Vous devez utiliser la source d’alimentation Intermec adéquate avec cet appareil sinon vous risquez d’endommager l’équipment.
CAUTION
!
™
You should check the Intermec MobileLAN Web site at http://mobilelan.intermec.com for free software downloads and the latest documentation.To upgrade your access point software, follow the instructions in the MobileLAN access System Manual.
Click Software Downloads.
CAUTION
!
Mountin
g
bracket and
shoulder scews (4
)
D
o
package
Po
wer
suppl
y
MobileLAN access 2101
Anten
n
6001 36th Avenue West Everett, WA 98203 U.S.A. www.intermec.com © 2002 Intermec Technologies Corp. All Rights Reserved
This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit (http://www.openssl.org). This product includes cryptographic software written by Eric Young ([email protected]).

Defining the LEDs and Ports
MobileLAN™access 2101 Quick Start Guide
1Attaching an Antenna
Mounting the 2101
Connect the 2101 to your network.You can either use an Ethernet cable to connect the Ethernet port to an Ethernet drop, or you can use the fiber optic port option. For help connecting the 2101 to your fiber optic network, see “Connecting to Your Fiber Optic Network” in the MobileLAN access System Manual.
Connect the 2101 to power.You can either use an AC power supply with the appropriate power cord or power over Ethernet. To use power over Ethernet, you use an Ethernet cable to connect the Ethernet port to a MobileLAN splitter, which is connected to a MobileLAN power bridge. For help, see the documentation that shipped with your splitter and/or power bridge.
3
4Setting an Initial IP Address
1
2
3
Install the MobileLAN access Utility on your PC by inserting the enclosed CD, clicking Install Software,and following the instructions that appear on your screen. You can also download the software from http://mobilelan.intermec.com.
Note: Your PC must be on the same Ethernet segment as the access point. Or, if your PC is communicating wirelessly with the access point, you must have an active radio connection.
Start the utility. Configure parameters A through C. See the screen to the right.
Click Set. Reboot the access point by disconnecting it from and reconnecting it to a power source.The Status box lets you know when the new IP address is successfully set.
1
5 4
3 2
Congratulations! Your wireless end devices can now begin transmitting data packets through the 2101 to your wired network.To continue configuring the access point, from the Actions menu choose Configure Access Point. Your Web browser application (for example, Internet Explorer) starts and the Access Point Login screen appears.
A Click the down arrow and choose Set IP Address. B Enter the Ethernet MAC address of the access point (printed on a label on the access point). C Enter the new IP address of the access point.
5
Note: Intermec offers a variety of antennas and antenna accessories. For a
complete list, see the MobileLAN access
System Manual (Part No. 067150) or
contact your local Intermec
reperesentative.
Carefully align the antenna with the antenna connector on the radio card in the 2101.
Gently insert the antenna into the antenna connector until you feel the antenna click into place.
1
2
Connecting the 2101
You can place the 2101 on a stable surface or you can mount it to a wall or beam using the wall bracket.
Antenna
Universal Access Point
™
Mounting screws (2-6 places)
Mounting bracket
Cable routing channels
To use the wall bracket Insert one shoulder screw into each of the brass inserts and tighten securely. Using the mounting bracket as a template, mark the location of the mounting holes on the mounting surface. Drill the holes.
Position the bracket on the wall with the arrow pointing up. Using mounting screws you provide, secure the bracket to the wall. Route the cables through the cable routing channels. Mount the 2101 in the bracket by insert- ing the shoulder screws into the keyhole slots in the bracket. Slide the 2101 down until it is firmly seated in the bracket.
Note: Intermec offers a variety of mounting bracket kits. For a complete list, see the MobileLAN access System Manual.
1
2
3
4 5 6 7
Serial port
10BaseT/100BaseTX Ethernet port
Power port
Fiber optic port (optional)
Power Remains on after the 2101 boots.
Wireless #1 Flashes when a frame is transmitted or received on the radio port for the radio installed in radio slot 1.
Wireless #2 Flashes when a frame is transmitted or received on the radio port for the radio installed in radio slot 2 (if a second radio is installed).
Wired LAN Flashes when a frame is transmitted or received on the Ethernet port.
Root/error Flashes if this 2101 is configured as the root. It remains on if an error is detected.
T
o power supply
To Ethernet
Shoulder screws (4 places)
Brass inserts
Mounting the 2101 (continued)
2