iroda PRO-25LK User manual

PRO-25LK
USB BATTERY RECHARGABLE SOLDERING IRON

• Readinstructionsbeforeuse.
• Workonlyinadryareafreefromammablematerials.
• KEEPAWAYFROMCHILDREN.
• Nevertouchthetipofahotsolderingironorattempttoremove
solderfromthetipwithyourhands.
• EnsurethatswitchisintheOFFpositionwhentheironisnotinuse.
• Tipremainshotafteruseforseveralminutes.Ensuretipiscool
beforestoringthesolderingiron.
• Donotdisassembleormodifythebattery.Thebatterycontains
safetyandprotectiondeviceswhichifdamaged,maycausethe
batterytogenerateheat,ruptureorignite.
• IfyourPRO-25Lmalfunctionsdonottrytorepair.Contactyour
dealeroronlinesupportforhelp.
23
IMPORTANT SAFETY
INSTRUCTIONS
Warnings:

DESCRIPTION
45
Cap
ToolessTip
Change
Power
Button
ON/OFF
Switch
Soldering
Tip
LEDCharging
Indicator
Co-molded
Handle
FlatBevel
-SafetyStand
Knurled
Nut
Locking
Nut

LEDLight
Micro-USB
Port
USB
Connector
MicroUSB
Connector
HOW TO USE PRO-25L
CHARGING (Fig.1)
1. ConnecttheMicro USB connectortotheMicroUSB
portattheendofthePRO25L.
2. ConnecttheUSB connectortoacomputerUSBport
orUSBwallcharger.
• Chargebatteryfor
atleast3.5hours
beforeuse.
• TheLED indicator
light willturnto
greenwhenfully
charged. Fig.1

8
Fig.2
SOLDERING
1. SlideON/OFFSwitchtoONposition(Fig.2)
2. PressandholdthePower Button.TheLED light
willilluminateindicatingtheironison.
3.Allowtiptoreachworkingtemperature(about8
seconds)
4.Applyasmallamountofsoldertotaperedsurface
oftip.
9
• Thoroughlycleanandremoveoilandother
contaminantsfrompartstobesoldered.
• Useonlysmallamountsofsolder.Excesssolder
cancauseashortcircuit.
5.Tinwiresbyheatingthebarewireandallowingasmallamountof
soldertoowontothetipofthewire.
6.Touchthetaperedsurfaceofthetip(notthepoint)tothejointto
besoldered.Heatjointandallowheatfromjointtomeltsolder.
7. Allowasmallamountofsoldertoowintothejoint.
8.Toensureastrongjoint,donottouchormovethejointuntilithas
cooledcompletely.
Note: Thetipassemblycanbeturnedtoany
desiredanglebyturningblackKnurled Nut.
Useplierstoadjusttoavoidtouchingtip.(Fig.3)
Fig.3

11
HOW TO REPLACE TIP
Fig.4
• EnsureswitchisintheOFFposition.Allowtip
tocoolcompletelybeforereplacingtip.
• UseonlygenuinePRO-25Lreplacementtips.
• Donotletip.
• Alwaystintipaftereveryusetoavoid
oxidation.
1. UnscrewoldtipbyrotatingLocking Nut
counterclockwise.(Fig.4)
2. ScrewinnewtipbyrotatingLocking Nut
clockwise.(Fig.4)
• Toreducetheriskofpersonalinjury,propertydamage,ordamage
toyourPRO-25Ldonotattempttorepairtheunitbody.
TROUBLE SHOOTING
• Thisproduct,whenusedforsolderingandsimilarapplications,
produceschemicalsknowntotheStateofCaliforniatocause
cancerandbirthdefectsorotherreproductiveharm.
SPECIAL WARNING
SPECIFICATIONS
Dimensions Length(WithCap) 260mm(10.2inches)
Width 29mm(1.1inches)
Height 40mm(1.6inches)
Weight 4.6oz.(130g)
BatteryCapacity 2900mAH
SolderingTip
Temperature
≈932°F±90°F(500°C±50°C)
HeatUpTime 8seconds
OperatingTime MidSetting 30-40mins

WARNING:
-Readtheinstructionsbeforeusingtheappliance.
CAUTION:
-Accessiblepartsmaybeveryhot.Keepyoungchildren
awayfromtheappliance.
www.pro-iroda.com