iroda SOLDERPRO 50K User manual

Pocket Sized Butane Soldering Iron Kit
Instruction Manual
READ INSTRUCTIONS AND WARNINGS BEFORE USE

IMPORTANT SAFETY
INSTRUCTIONS
Warnings:
• Unitusesammablegas(Butane)underpressure–usewithcare.
• DONOTexposetoheatabove+50°C(120°F)andavoidprolonged
exposuretothesun.
• DONOTpunctureorincinerate.
• DONOTrell,igniteorusenearopename,heater,furnaceor
combustiblematerials.
• Keepworkareaclean.Clutteredareasandbenchesinviteinjuries.
• KEEPAWAYFROMCHILDREN.Visitorsshouldbekeptawayfrom
workarea.
• Storeindry,lockedcabinetoutofreachofchildren.
• Beextremelycarefulastorchametiptemperatureisover1300°C
(2400°F)
• Beextremelycarefulastorchameisalmostinvisibleindaylightor
understronglight.
• UseSafetyGlasses.
• Donottouchtheheatedtipoftheunit.
• DONOTleaveunitunattendedwhenoperatingorhot.
• Alwaysbesureunitiscoolbeforestoring.
• DONOTreplacecapwithoutswitchingunitoandensuringtiphas
cooled.
• Ifyourtorchmalfunctionsdonottrytorepair.Contactyourdealer
oronlinesupportforhelp.
• Butane-Propanemixorotherfuelcouldcreatemuchhigher
temperaturesandcauseare-upatthetipexhaustslots.
2 3

DESCRIPTION
4 5
FlintIgnitor Cap
Soldering
Tip
Safety
WireStand
GasTank Transparent
Window
Filling
Valve
ON/OFFGas
ControlLever
Ignition
Point

HOW TO USE THE
SOLDERPRO 50K
6 7
REFILLING
IGNITION
• Useonlyhigh-qualitybutanegas.
• Rellinawell-ventilatedareaawayfromanyignition
sourceandotherpeople.
1. Holdbutanecanisterupsidedownwhenlling(Fig.1)
2. FirmlypresscanisternozzleintoGas Filling Valve.
3. Releasecanisterwhengasstartstoover ow.
(Gasoverowduringrellingisnormalanddoesnot
indicatealeak)
4. Waitforafewminutesbeforeuse.
1. PushtheON/OFF leverupwardandtothe
right,andsettomidposition.(Fig.2)
2. IgnitethegasstreamwiththeFlint Ignitor
locatedontheTorchCap.(Fig.3aFig.3b)
(Youcanalsousearegularlighter.)Thetip
willameforafewsecondsandthenthe
catalystwillchangetoanorangeglow.
Fig.1
Fig.2
Fig.3a Fig.3b
Fig.1
Butane

IGNITION WARNINGS
8 9
TEMPERATURE ADJUSTMENT
• DonottouchTip,TipHousingorKnurledNutwhileigniting.(Fig.4)
• DonotignitetorchwhenTipAssemblyisnotscrewedon.(Fig.5)
• ThetiptemperaturecanbeadjustedbyturningtheON/OFF Gas
Control Leverleftorright.(Fig.6)
• Settomid-positionwhensolderingorbrazing.
• Excessivegasow,are-uporcatalystpulsingredmayoccur
whentheGas Control Leverissettoohigh.
Fig.4 Fig.5 Fig.6

CHANGING TIPS
10 11
CLEANING
1. Besurethetiphascooledbeforeremoval.
2. Unscrewtipwithacounterclockwise
motion.(Fig.7)Pliersmayberequiredto
lightlygraspthetipinordertoloosenit.
3.Replacewithdesiredtip.Becarefulnot
toovertightenasthiscoulddamagethe
threadinthecap.
WARNING: The catalyst inside the
soldering tip is very delicate and will
not sustain mechanical abuse without
serious damage.
• Useonlymildsoapandadampclothtocleanthehousingsofthe
tool.Manyhouseholdcleanerscontainchemicalswhichcould
seriouslydamagetheplastic.Alsodonotusegasoline,turpentine,
lacquerorpaintthinner,drycleaninguidsorsimilarproducts.
Neverletanyliquidgetinsidethetool;neverimmerseanypartof
thetoolintoaliquid.
Fig.7

TROUBLE SHOOTING
12 13
SPECIAL WARNING
• Thisproduct,whenusedforsolderingandsimilarapplications,
produceschemicalsknowntotheStateofCaliforniatocause
cancerandbirthdefectsorotherreproductiveharm.
• DepartmentofTransportationHazardousMaterialsRegulations
forbidthecarriageofbutaneorotherammablegasproductson
passengeraircraft.Donotpackthisitemoranyotherammable
gasitem,inanycheckedorcarry-onbaggage.
• Toreducetheriskofpersonalinjury,propertydamage,ordamage
toyourSOLDERPRO50,donotattempttorepairtheunitbody.
PROBLEM PROBABLECAUSE HOWTOCORRECT
Doesnot
ignite
a. EmptyGasTank
b.Toohighorlowfuel
pressure
c. Pushingon/oignition
switchtoofast.
a. Rellwithbutanefuel
b.Adjustcontrollevertoa
higherorlowerposition.
c. Re-readIGNITIONsteps
Lowgas
pressureor
lowame
a. Coldfuel
b.Lowfuel
a. Holdbodyinhandsto
allowunittowarmup.
b.Refuel
Tipdoesnot
heatup
a. Used-upcatalyst
b.Insucientfuel
pressure
a. Replacewithnewtip.
b.Adjustcontrollevertoa
higherposition.

SPECIFICATIONS
14
Length W/Cap 155mm(6.1inches)
W/SolderingTip 140mm(5.5inches)
Height 28mm(1.1inches)
Weight EmptyFuelTank 56g±2g
Watt 30W-70W
BTU 346.5
Approximate
Temperature
SolderingTip ≈842℉(450℃)
Torch ≈2400℉(1300℃)
HotKnife ≈842℉(450℃)
HeatBlower ≈1300℉(650℃)
Capacity GasContainer 7ml(0.24oz)
FlameLength MidSetting 1cm(0.4inches)
OperatingTime MidSetting/OneGasFilling 40min.
HeatUpTime WorkingTemperature 18seconds
Thisappliancemaybelledwithanycartridgesmarked
“Butane”complyingwithEN417.
Warning:
-Useoutdoorsonlyoruseinwellventilatedareas.
-Readtheinstructionsbeforeusingtheappliance.
CAUTION:
-Accessiblepartsmaybeveryhot.Keepyoungchildren
awayfromtheappliance.

www.pro-iroda.com