iroda SOLDERPRO 120K User manual

+
-
Premium Butane Soldering Iron Kit

• Unitusesammablegas(Butane)underpressure–usewithcare.
• DONOTexposetoheatabove+50°C(120°F)andavoidprolonged
exposuretothesun.
• DONOTpunctureorincinerate.
• DONOTrell,igniteorusenearopename,heater,furnaceor
combustiblematerials.
• Keepworkareaclean.Clutteredareasandbenchesinviteinjuries.
• KEEPAWAYFROMCHILDREN.Visitorsshouldbekeptawayfrom
workarea.
• Storeindry,lockedcabinetoutofreachofchildren.
• Beextremelycarefulastorchametiptemperatureisover1300°C
(2400°F)
• Beextremelycarefulastorchameisalmostinvisibleindaylightor
understronglight.
• UseSafetyGlasses.
• Donottouchtheheatedtipoftheunit.
• DONOTleaveunitunattendedwhenoperatingorhot.
• Alwaysbesureunitiscoolbeforestoring.
• DONOTreplacecapwithoutswitchingunitoandensuringtiphas
cooled.
• Ifyourtorchmalfunctionsdonottrytorepair.Contactyourdealer
oronlinesupportforhelp.
• Butane-Propanemixorotherfuelcouldcreatemuchhigher
temperaturesandcauseare-upatthetipexhaustslots.
2 3
IMPORTANT SAFETY
INSTRUCTIONS
Warnings:

DESCRIPTION
4 5
+
-
Cap
Soldering
Tip
Knurled
Nut
GasTank
Filling
Valve
ON/OFFIgnition
Switch
GasControl
Lever
Transparent
Window
TipAssembly

HOW TO USE THE
SOLDERPRO 120K
6 7
REFILLING
• Useonlyhigh-qualitybutanegas.
• Rellinawell-ventilatedareaawayfromanyignition
sourceandotherpeople.
1. Holdbutanecanisterupsidedownwhenlling(Fig.1)
2. FirmlypresscanisternozzleintoGas Filling Valve.
3. Releasecanisterwhengasstartstooverow.
(Gasoverowduringrellingisnormalanddoesnot
indicatealeak)
4. Waitforafewminutesbeforeuse.
Fig.1
Fig.2
Fig.3
Fig.1
+
-
Butane
IGNITION
1. SetGas Control Leveratmidposition.(Fig.2)
2. slideuptheON/OFF Ignition Switch(Fig.3)
tothe"ON"positiontostarttheowofgas.
3.Asgasisowing,continueslidingtheIgnition
Switchtowardthetiptillyouhearaclick.The
automaticignitionwilllightthegas.
4.Releasetheswitchanditwillautomaticallymove
backtothe"ON"position.
5.Thetiphousingwillstarttoglowred.Ifnot,slide
theON/OFF Ignition Switchbacktothe“OFF”
positionandrepeatsteps2and3.
6.Toturno,slidetheON/OFF Ignition Switch
downwardtotheOFFposition.
Slowly

8 9
• DonottouchTip,TipHousingorKnurledNutwhileigniting.(Fig.4)
• DonotignitetorchwhenTipAssemblyisnotscrewedon.(Fig.5)
• Thetiptemperaturecanbeadjustedbyturning
theGas Control Leverleftorright.(Fig.6)
• Settomid-positionwhensolderingor
brazing.
• Excessivegasow,are-uporcatalystpulsing
redmayoccurwhentheGas Control Leveris
settoohigh.
Fig.4 Fig.5
Fig.6
Mid-Position
IGNITION WARNINGS TEMPERATURE ADJUSTMENT

10 11
CLEANING OR
REPLACING NOZZLE
ASSEMBLY
1. Besurethetiphascooledbefore
removal.
2. UnscrewTipAssemblywitha
counterclockwisemotion.(Fig.7)Pliers
mayberequiredtolightlygraspthe
Knurled Nutinordertoloosenthetip.
3.Replacewithdesiredtip.Becarefulnot
toovertightenasthiscoulddamagethe
threadinthecap.
1. RemoveTipAssembly
2. UnscrewNozzle Assembly (A)fromtheTorch Body (C).(Fig.8)
Pliersmaybeusedtolightlygrasptheshankinordertoloosenit.
Do not graspandturntheCeramic Head. (D)
3.CarefullyremoveOrice connector (B)byliftingitoutofthe
torchbody.Notethattheshorter side of Orice Connector ts
into the Torch Body.
4.SoakOriceConnectorinNaphthaorothersimilarsolventfor
approximately5minutes.
Fig.8
Fig.7
NozzleAssembly
CHANGING TIPS
WARNING: The catalyst inside the
soldering tip is very delicate and
will not sustain mechanical abuse
without serious damage.
Knurled
Nut

TROUBLE SHOOTING
CLEANING
12
• Toreducetheriskofpersonalinjury,propertydamage,ordamage
toyourSOLDERPRO 120K,donotattempttorepairtheunitbody.
PROBLEM PROBABLECAUSE HOWTOCORRECT
Doesnot
ignite
a. EmptyGasTank
b. Toohighorlowfuel
pressure
c. Pushingon/oignition
switchtoofast.
d. Cloggedoriceconnector
a. Rellwithbutanefuel
b. Adjustcontrollevertoa
higherorlowerposition.
c. Re-read"Howtouseasa
solderingiron"
d. Cleanorreplacewithnew
oriceassembly
Lowgas
pressureor
lowame
a. Cloggedoriceconnector
b. Coldfuel
c. Lowfuel
a. Cleanorreplacewithnew
one.
b. Holdbodyinhandsto
allowunittowarmup.
c. Refuel
Tipdoes
notheatup
a. Used-upcatalyst(inside
TipHousing)
b. Insucientfuelpressure
c. Cloggedoriceconnector
a. Replacewithnewtip.
b. Adjustcontrollevertoa
higherposition.
c. Cleanorreplacewithnew
one.
5.Replacenew(orclean)Oriceconnector(B)rememberingto
inserttheshorter side into the Torch Body.
6.ReplaceNozzleAssemblyandhandtightenortightengentlywith
pliersgraspingtheshankoftheNozzleAssemblynottheceramic
head.
7. ReplaceTipAssembly.
• Useonlymildsoapandadampclothtocleanthehousingsof
thetool.Manyhouseholdcleanerscontainchemicalswhich
couldseriouslydamagetheplastic.Alsodonotusegasoline,
turpentine,lacquerorpaintthinner,drycleaninguidsorsimilar
products.Neverletanyliquidgetinsidethetool;neverimmerse
anypartofthetoolintoaliquid.

SPECIFICATIONS
14
Length W/Cap 272mm(10.7inches)
W/SolderingTip 262mm(10.4inches)
Width 28mm(1.1inches)
Height W/Stand 65mm(2.6inches)
W/OStand 36mm(1.4inches)
Weight EmptyFuelTank 193g±2g
Watt 30W-125W
BTU 594
Approximate
Temperature
SolderingTip ≈842℉(450℃)
HeatBlower ≈130℉(650℃)
Deector ≈1300℉(650℃)
Capacity GasContainer 15ml(0.5oz)
FlameLength MidSetting 1.2cm(0.5inches)
OperatingTime MidSetting/OneGasFilling 40min.
HeatUpTime WorkingTemperature 25seconds
SPECIAL WARNING
• Thisproduct,whenusedforsolderingandsimilarapplications,
produceschemicalsknowntotheStateofCaliforniatocause
cancerandbirthdefectsorotherreproductiveharm.
• DepartmentofTransportationHazardousMaterialsRegulations
forbidthecarriageofbutaneorotherammablegasproductson
passengeraircraft.Donotpackthisitemoranyotherammable
gasitem,inanycheckedorcarry-onbaggage.

www.pro-iroda.com
Thisappliancemaybelledwithanycartridgesmarked
“Butane”complyingwithEN417.
Warning:
-Useoutdoorsonlyoruseinwellventilatedareas.
-Readtheinstructionsbeforeusingtheappliance.
CAUTION:
-Accessiblepartsmaybeveryhot.Keepyoungchildren
awayfromtheappliance.