Iron Horse Cooltouch WLED80 User manual

120º
even
light
beam
120º
even
light
beam
wled80
cool + energy efficient light
Technical DaTa WaRRanTY
Arlec guarantees this product in accordance with the
Australian Consumer Law.
Arlec also warrants to the original first purchaser of
this product (“you”) from a retailer that this product will
be free of defects in materials and workmanship for a
period of 12 months from the date of purchase; provided
the product is not used other than for the purpose, or in
a manner not within the scope of the recommendations
and limitations, specified by Arlec, is new and not
damaged at the time of purchase, has not been
subjected to abuse, misuse, neglect or damage, has
not been modified or repaired without the approval of
Arlec and has not been used for commercial purposes
(“Warranty”).
If you wish to claim on the Warranty, you must, at your
own expense, return the product, and provide proof
of original purchase and your name, address and
telephone number, to Arlec at the address below or the
retailer from whom you originally purchased the product
within 12 months from the date of purchase.
Arlec will (or authorise the retailer to) assess any claim
you may make on the Warranty in the above manner
and if, in Arlec’s reasonable opinion, the Warranty
applies, Arlec will at its own option and expense (or
authorise the retailer to) replace the product with the
same or similar product or repair the product and return
it to you or refund the price you paid for the product.
Arlec will bear its own expenses of doing those things,
and you must bear any other expenses of claiming on
the Warranty.
The Warranty is in addition to other rights and remedies
you may have under a law in relation to the product to
which the Warranty relates.
Our goods come with guarantees that cannot be
excluded under the Australian Consumer Law.
You are entitled to a replacement or refund for a major
failure and for compensation for any other reasonably
foreseeable loss or damage. You are also entitled to
have the goods repaired or replaced if the goods fail to
be of acceptable quality and the failure does not amount
to a major failure.
Specifications
Input Voltage 220-240Vac, 50Hz
Max Wattage 32W (2x16W)
LEDs 80 Super bright surface
mount type 5.6x3.0x0.9mm
(Non Replaceable type )
IP Classification IP44
Protective Shield Glass Lens
233 x 185 x 5mm thick
Construction
Enclosure Zinc / Aluminium Alloy
Glass / Lens 5mm thick tempered safety
Reflector 2.0mm thick metallic finish
Colour Green
CPIN002331
For All Sales & Warranty Enquiries
Arlec Australia Pty. Ltd. ACN 009 322 105
(“Arlec”) gives the Warranty.
Building 3, 31 – 41 Joseph Street,
Blackburn North, Victoria, 3130
Blackburn North LPO, P.O. Box 1065, Blackburn North, 3130
Customer Service: [phone]
Email: [e-mail]
© This instruction leaflet is subject to copyright and must not be reproduced,
copied or otherwise used in any way or for any purpose without the consent
in writing of the owner, Arlec Australia Pty Ltd (A.C.N. 009 322 105).
LED technology featuring a metalized
coated reflector that provides an even
and wide angle beam, protected by a
Cool to touCh
durable diecast aluminium housing
led
Extra bright
WORKlIGHT
3000 LUMEN
Provides high intensity even
light distribution
High output LED module array
CPIN002331
WLED80_Instructions.indd 1-2 13/03/12 3:20 PM

2 3
The Arlec WLED80, 32 Watt twin LED worklight is suitable for indoor (ambient temperature 25˚C) or temporary
outdoor use. The worklight can be plugged into a standard power point and has a weather proof classification of
IP44. WLED80 allows 2 different light levels 16W and 32 W which can be controlled with rocker switches located at
the rear of the lanterns.
inTRODUcTiOn
aSSeMBlY
Assemble unit as shown in the figure. Fix each
worklight head support bracket to the crossbar using
a bolt and threaded knob supplied in a separate poly
bag along with the unit. Ensure that the threaded
knobs are tight and firmly holds the assembly
together. Fix the “Y” junction of the power cord to the
centrally located mounting hole on the cross bar
To adjust the tilt of the lamp head, loosen the moulded
knobs attached at each end of the support bracket
and with the help of the carry handle tilt the lamp
head to a desired angle. Once the desired angle is
achieved tighten the moulded knobs to hold the
worklight head in position.
To assemble the worklight on a tripod stand loosen
the locking knob on the tripod and push down the
black locking bracket until the legs are fully extended.
Tighten the locking knob. Always make sure the
central telescopic pole is vertical for maximum
stability and safety while the outer tube sits flat on
the black metal cap at the bottom and is secured by
wing knob.
The crossbar is mounted on the metal bracket
attached to the central tube of the telescopic and is
secured with a threaded knob. Ensure that the
threaded knob is tight and securely holds the
assembly together.
The poles of the tripod stand can be raised by
loosening the plastic locking ring (anti clockwise
direction) and extending the sections. Tighten locking
ring (clockwise direction) to hold the poles in place.
Two plastic locking rings on the tripod allow height
adjustment up to 1700mm. (to top of tripod)
NOTE
The worklight has a safety adjustment stop which
prevents the worklight head from tilting too far forward.
Do not remove support bracket from worklight body.
While adjusting the lamp head avoid pinching
or bending of the supply cord
Tighten locking
rings to hold the
poles in place.
Crossbar
locking bracket
Y junction
power cord
Locking knob Locking bracket
Carry
handle
Metal cap
OpeRaTiOn
WARNING:
• Tripod legs must be at widest spread for maximum stability.
• When the worklight is operated outdoors the supply cord must be
appropriately covered or located such that it is subjected to
indoor conditions only.
• If the external flexible cable or cord of this worklight is damaged,
it shall be exclusively replaced by the manufacturer or his service
agent or a similar qualified person in order to avoid hazard.
IMPORTANT NOTES:
Do not open the worklight body, no user serviceable parts inside.
Do not immerse in water or other liquid.
Do not use abrasive cleaners, clean with damp cloth
• 2x 16 Watts LED array (40 LED modules)
• Provides high intensity even light distribution
• Indoor / Outdoor lighting for Contractor,
Tradesman, & DIY Applications
• Cool to touch durable diecast aluminium housing
• Wide angle coverage for large work areas
• Weatherproof rating IP44
high OUTpUT leD MODUle aRRaY
• To operate plug the worklight into
a standard power point.
• Adjust the tilt of lamp head to a
desired angle.
• Each worklight head can be
individually controlled using the
rocker switch located on the
terminal housing at the rear of
the unit. With one rocker switch
pushed to ON position the power
output is 16W and when both
the switches are pushed to ON
the power output is double
and is 32W.
Easy Grip Locking Nuts
Plastic Locking rings
Tripod legs must be at widest
spread for maximum stability
Sealed dust proof
ON/OFF switch
Support
bracket
WLED80_Instructions.indd 3-4 13/03/12 3:20 PM