Iron Horse WLED100 User manual

CPIN003059/2
Important! Please read these instructions carefully before use
Due to continuous research and development the specifications herein are subject to change without notice.
Arlec Australia Pty. Ltd. ACN 009 322 105 (“Arlec”) gives the Warranty.
Arlec’s telephone number, address and email address are:
Customer Service: [phone]
New Zealand Toll Free: 0800 003 329
Building 3, 31 – 41 Joseph Street, Blackburn North, Victoria, 3130
Blackburn North LPO, P.O. Box 1065, Blackburn North, 3130
Email: cus[email protected] CPIN003059/2
Warranty
Arlec guarantees this product in accordance
with the Australian Consumer Law.
Arlec also warrants to the original first
purchaser of this product (“you”) from a
retailer that this product will be free of
defects in materials and workmanship for
a period of 24 months from the date of
purchase; provided the product is not used
other than for the purpose, or in a manner not
within the scope of the recommendations
and limitations, specified by Arlec, is new
and not damaged at the time of purchase,
has not been subjected to abuse, misuse,
neglect or damage, has not been modified
or repaired without the approval of Arlec and
has not been used for commercial purposes
(“Warranty”).
Ifyou wishtoclaimonthe Warranty,youmust,
at your own expense, return the product,
and provide proof of original purchase and
your name, address and telephone number,
to Arlec at the address below or the retailer
from whom you originally purchased the
product within 24 months from the date of
purchase.
Arlec will (or authorise the retailer to) assess
any claim you may make on the Warranty
in the above manner and if, in Arlec’s
reasonable opinion, the Warranty applies,
Arlec will at its own option and expense (or
authorise the retailer to) replace the product
with the same or similar product or repair
the product and return it to you or refund
the price you paid for the product. Arlec will
bear its own expenses of doing those things,
and you must bear any other expenses of
claiming on the Warranty.
The Warranty is in addition to other rights
and remedies you may have under a law in
relation to the product to which the Warranty
relates.
Our goods come with guarantees that
cannot be excluded under the Australian
Consumer Law. You are entitled to a
replacement or refund for a major failure and
for compensation for any other reasonably
foreseeable loss or damage. You are also
entitled to have the goods repaired or
replaced if the goods fail to be of acceptable
quality and the failure does not amount to a
major failure.
OPERATING INSTRUCTIONS
2 x 50W SUPER BRIGHT
LED
WORKLIGHT
WLED100

23
CPIN003059/2
Introduction
The Ironhorse WLED100 is suitable for
indoor and temporary outdoor use. When
used outdoors the supply plug and socket-
outlet must be suitably protected against
water ingress.
Assembly
Assemble unit as shown in the figure. Fix
each worklight support bracket to the
crossbar using a nut and threaded knob
supplied along with the unit. Ensure that
the threaded knobs are tight and firmly hold
the assembly together. Fix the “T” junction
of the power cord to the central Knob that
hold the crossbar to the tripod
Before attaching the worklights to the
tripod stand loosen the locking knob on
the tripod and push down the black locking
bracket until the legs are fully extended.
Tighten the locking knob. Always make
sure the central telescopic pole is vertical
for maximum stability and safety while the
outer tube sits flat on the black metal cap
at the bottom and is secured by wing knob.
The crossbar is mounted on the central
tube of the stand and is secured with a
threaded knob. Ensure that the threaded
knob is tight and securely holds the
assembly together.
The poles of the tripod stand can be raised
by loosening the plastic locking ring (anti
clockwise direction) and extending the
sections. Tighten locking ring (clockwise
direction) to hold the poles in place.
Two plastic locking rings on the tripod allow
height adjustment up to 1500mm. (to top
of tripod)
WARNING
Tripod legs must be at widest spread for
maximum stability
Use of Worklight
1. Adjust the tilt of the top of the lamp
head by pushing the head forward or
backward to the desired position until the
desired angle is obtained. You may need to
loosen and retighten the knobs that fix the
lamp head to their brackets
2. Plug the worklight into a power point.
3. Turn on the power to the worklight
Important Notes:
Do not use without tripod legs spread
widest for maximum stability
Do not remove the support bracket from
the lamp body.
Do not pinch or sharply bend the supply
cord while adjusting the lamp head.
Do not open the worklight body, there are
no user serviceable parts inside.
Do not immerse in water or any other liquid.
Do not use abrasive cleaners, clean with a
damp cloth.
If the supply flexible cord is damaged it
shall only be replaced by a service agent or
similarly person in order to avoid a hazard.
High Output Led Module Array
• 2 x 50W LED array
• Provides high intensity even light
distribution
• Indoor/Outdoor lighting for contractor,
tradesman, and DIY applications
• Cool to touch durable diecast aluminium
housing
• Wide angle coverage for large work areas
• Weatherproof IP44 rating.
Specifications
Input Voltage: 220-240Vac; 50Hz
Wattage: 2 x 50W
IP Classification: IP44
LED: Super bright module;
4000 Lumen
50 x 1W LED array 5000K
each lantern
Protective Shield: Polycarbonate lens
Enclosure: Zinc / Aluminium Alloy
Crossbar T Junction
power cord
Tighten locking
rings to hold the
poles in place
Locking knobLocking
bracket
Metal cap