Iron Horse WLED40 User manual

Technical DaTa WaRRanTY
Arlec guarantees this product in accordance with the
Australian Consumer Law.
Arlec also warrants to the original first purchaser of
this product (“you”) from a retailer that this product will
be free of defects in materials and workmanship for a
period of 12 months from the date of purchase; provided
the product is not used other than for the purpose, or in
a manner not within the scope of the recommendations
and limitations, specified by Arlec, is new and not
damaged at the time of purchase, has not been
subjected to abuse, misuse, neglect or damage, has
not been modified or repaired without the approval of
Arlec and has not been used for commercial purposes
(“Warranty”).
If you wish to claim on the Warranty, you must, at your
own expense, return the product, and provide proof
of original purchase and your name, address and
telephone number, to Arlec at the address below or the
retailer from whom you originally purchased the product
within 12 months from the date of purchase.
Arlec will (or authorise the retailer to) assess any claim
you may make on the Warranty in the above manner
and if, in Arlec’s reasonable opinion, the Warranty
applies, Arlec will at its own option and expense (or
authorise the retailer to) replace the product with the
same or similar product or repair the product and return
it to you or refund the price you paid for the product.
Arlec will bear its own expenses of doing those things,
and you must bear any other expenses of claiming on
the Warranty.
The Warranty is in addition to other rights and remedies
you may have under a law in relation to the product to
which the Warranty relates.
Our goods come with guarantees that cannot be
excluded under the Australian Consumer Law.
You are entitled to a replacement or refund for a major
failure and for compensation for any other reasonably
foreseeable loss or damage. You are also entitled to
have the goods repaired or replaced if the goods fail to
be of acceptable quality and the failure does not amount
to a major failure.
Specifications
Input Voltage 220-240Vac, 50Hz
Max Wattage 16W
LEDs 40 Super bright surface
mount type 5.6x3.0x0.9mm
(Non Replaceable type )
IP Classification IP44
Protective Shield Glass Lens
233 x 185 x 5mm thick
Construction
Enclosure Zinc / Aluminium Alloy
Glass / Lens 5mm thick tempered safety
Reflector 2.0mm thick metallic finish
Colour Green
CPIN002327
CPIN002327
120º
even
light
beam
16 Watts LED array
(40 LED modules)
Provides high intensity even
light distribution
wled40
LED technology featuring a metalized
coated reflector that provides an even
and wide angle beam, protected by a
Cool to touCh
durable diecast aluminium housing
cool + energy efficient light
For All Sales & Warranty Enquiries
Arlec Australia Pty. Ltd. ACN 009 322 105
(“Arlec”) gives the Warranty.
Building 3, 31 – 41 Joseph Street,
Blackburn North, Victoria, 3130
Blackburn North LPO, P.O. Box 1065, Blackburn North, 3130
Customer Service: [phone]
Email: [e-mail]
© This instruction leaflet is subject to copyright and must not be reproduced,
copied or otherwise used in any way or for any purpose without the consent
in writing of the owner, Arlec Australia Pty Ltd (A.C.N. 009 322 105).
led
Extra bright
WORKlIGHT
1500 LUMEN
WLED40_Instructions.indd 1-2 13/03/12 4:52 PM

The Arlec WLED40, 16W LED Worklight is suitable for indoor or temporary outdoor used. The worklight can be
plugged into a standard power point and has a weather proof classification of IP44.
inTRODUcTiOn
2 3
aSSeMBlY
USe OF WORKliGhT
Carry
Handle
Support
bracket
H Base
Stand
Assemble the worklight as shown in the figure. Fix the support bracket of lamp head onto the base
stand with 2 self threaded bolts and nuts supplied. Ensure that the nuts are tight and firmly holds the
support bracket and base stand assembly together.
To adjust the tilt of the lamp head, loosen the moulded knob attached at the end of the support bracket
and with the help of the carry handle tilt the lamp head to a desired angle. Once the desired angle is
achieved tighten the moulded knobs to hold the lamp head in position.
Note: Do not remove the support bracket from the lantern body.
While adjusting the lamp head avoid pinching or bending of the supply cord.
1. To operate plug the worklight into a standard power point.
2. Adjust the tilt of lamp head to a desired angle.
3. Press the power on switch located on the terminal housing
cover at the rear of the housing to ON position.
WARNING
When the luminaire is operated outdoors the supply cord must be appropriately covered or located
such that it is subjected to indoor conditions only.
If the external flexible cord of this luminaire is damaged, contact the Arlec Customer Service team.
(Refer to details on back page) or similar qualified person in order to avoid hazard.
Easy Grip Locking Nuts
Sealed dust proof
ON/OFF switch
1.8m power cord
IMPORTANT NOTES:
Do not open the worklight body, no user serviceable parts inside.
Do not immerse in water or other liquid.
Do not use abrasive cleaners, clean with damp cloth
• 16 Watts LED array (40 LED modules)
• Provides high intensity even
light distribution
• Indoor / Outdoor lighting for Contractor,
Tradesman, & DIY Applications
• Cool to touch durable diecast
aluminium housing
• Wide angle coverage for large work areas
• Weatherproof rating IP44
120º
even
light
beam
hiGh OUTpUT leD MODUle aRRaY
WLED40_Instructions.indd 3-4 13/03/12 4:52 PM