iStorage datAshur BT User manual

ADMIN MANUAL
#1
www.istorage-uk.com
iStorage datAshur®BT ADMIN MANUAL v 1.7
ADMIN MANUAL

#2
iStorage datAshur® BT ADMIN MANUAL v 1.7
www.istorage-uk.com
ADMIN MANUAL
iStorage datAshur is developed and
manufactured by iStorage Limited and is
based on DataLock® technology licensed
from ClevX, LLC.
iStorage datAshur BT is manufactured by
iStorage Ltd. and is using DataLock® technology
licensed from ClevX, LLC. U.S. Patent.
www.istorage-uk.com/clevx-patents
All trademarks and brand names are the property of their
respective owners
Copyright © 2020 iStorage Limited. All rights reserved.
Windows is a registered trademark of Microsoft Corporation.
All other trademarks and copyrights referred to are the property of their respective owners.
Distribution of the work or derivative work in any standard (paper) book form for commercial purposes is prohibited unless
prior permission is obtained from the copyright holder.
DOCUMENTATION IS PROVIDED AS IS AND ALL EXPRESS OR IMPLIED CONDITIONS, REPRESENTATIONS AND
WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE OR NON-INFRINGEMENT, ARE DISCLAIMED, EXCEPT TO THE EXTENT THAT SUCH DISCLAIMERS ARE HELD
TO BE LEGALLY INVALID
iStorage shall not be liable by virtue of this warranty, or otherwise, for any incidental, special or consequential damage
including any loss of data resulting from use or operation of the product, whether or not iStorage was apprised of the
possibility of such damages
EMI Cautions
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installa-
tion. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Cautions
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to
operate this device. The normal function of the product may be disturbed by strong Electro-Magnetic Interference. If so, sim-
ply reset the product to resume normal operation by following the instruction manual. In case the function could not resume,
please use the product in other location.”
This device complies with part 15 of the FCC Rules and with Industry Canada License-exempt RSSs. Operation is subject to
the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any inter-
ference received, including interference that may cause undesired operation.
RF Exposure Statement
The device has been evaluated to meet general RF exposure requirement.

#3
www.istorage-uk.com
iStorage datAshur®BT ADMIN MANUAL v 1.7
ADMIN MANUAL
Table of Contents
Introduction ........................................................................................................................................................................ 4
Box contents ....................................................................................................................................................................... 4
Useful Links........................................................................................................................................................................ 4
datAshur BT Layout ............................................................................................................................................................ 5
Drive LED Indicators and their actions ................................................................................................................................ 5
1. Registration............................................................................................................................................................... 6
2. How to enroll as an Administrator (Admin) ....................................................................................................... 7
3. How to Provision datAshur BT Managed Drives ................................................................................................ 8
4. How to Create Users via the Remote Management Console ......................................................................... 11
5. How to Assign Drives to Users .............................................................................................................................. 12
6. Managing Users Dashboard .................................................................................................................................. 13
User Dashboard at a glance ........................................................................................................................................ 13
How to Enable or Disable User Access........................................................................................................................ 13
How to Delete a User from Remote Management ....................................................................................................... 13
How to Reset User’s datAshur BT Managed App Password ......................................................................................... 13
Search Bar................................................................................................................................................................... 14
Opening the Geo & Time-Fencing Panel..................................................................................................................... 14
7. Managing Drives Dashboard ................................................................................................................................. 14
Drives Dashboard at a glance...................................................................................................................................... 14
How to Delete a Drive from Remote Management ....................................................................................................... 15
Search by Drive Serial Number ................................................................................................................................... 15
Managing Access Control........................................................................................................................................... 15
How to Wipe a Drive via Remote Management............................................................................................................ 16
How to Change a Drive Password via Remote Management........................................................................................ 16
How to Unlock a Drive via Remote Management......................................................................................................... 16
Viewing Assigned to & Access Log............................................................................................................................. 17
8. How to Apply Geo & Time-Fencing Restrictions................................................................................................ 17
Geo & Time-Fencing at a glance................................................................................................................................. 17
Allowed Drives............................................................................................................................................................ 18
How to set Time-Fencing Restrictions......................................................................................................................... 18
How to set Geo-Fencing Restrictions .......................................................................................................................... 18
9. How to Change the Admin Password ................................................................................................................... 19
10. Account Summary .................................................................................................................................................... 19
11. How to Provision a Non-Managed Drive ............................................................................................................. 20
12. Formatting the datAshur BT for Windows ........................................................................................................... 23
13. Formatting the datAshur BT for mac OS.............................................................................................................. 24
14. Technical Support..................................................................................................................................................... 27
15. Warranty and RMA information............................................................................................................................. 27

#4
iStorage datAshur® BT ADMIN MANUAL v 1.7
www.istorage-uk.com
ADMIN MANUAL
Introduction
Thank you for purchasing the Managed Drive subscription for the datAshur BT, a hardware encrypted USB 3.2 Gen 1 flash
drive that utilises mobile phone technology via Bluetooth and turns your (iOS/Android) Smartphone into a wireless
user-authentication device that enables secure access to data stored on your datAshur BT Managed flash drive.
The datAshur BT Managed Drive uses military grade AES-XTS 256-bit hardware encryption (full disk encryption), which
encrypts all data stored on the drive in real-time.
The datAshur BT Managed Drive is designed for remote management via the web-based iStorage Remote Management
Console that allows the Administrator to control where and when the Drive can be accessed with Geo and Time-Fencing.
Additional features include, remote wipe, remote unlock, change passwords, disable access and more.
Box Contents
• iStorage datAshur BT
• QSG - Quick Start Guide for ‘Non-Managed’ datAshur BT Personal
Note: The datAshur BT packaging contains a QSG insert applicable only to the ‘Non-Managed’
datAshur BT Personal. Please ignore the QSG insert and refer to the instructions contained in this manual.
Useful Links
1. datAshur BT Admin Registration Link: https://rm.bt.istorage-uk.com/Account/Register
2. Remote Management Login Link: https://rm.bt.istorage-uk.com/Account/Login
3. datAshur BT Managed User Manual: https://istorage-uk.com/product-documentation/
4. datAshur BT Managed User QSG: https://istorage-uk.com/product-documentation/
5. datAshur BT Personal User Manual: https://istorage-uk.com/product-documentation/

#5
www.istorage-uk.com
iStorage datAshur®BT ADMIN MANUAL v 1.7
ADMIN MANUAL
datAshur BT Layout
Drive LED indicators and their actions
LEDs LED State Description
All LEDs blink once datAshur BT conducts a self test when plugged to a computer
Solid Red Locked - datAshur BT App not open
Blinking Red Locked - datAshur BT App open
Solid Blue datAshur BT is unlocked
Blinking Blue datAshur BT is unlocked and communication in progress

#6
iStorage datAshur® BT ADMIN MANUAL v 1.7
www.istorage-uk.com
ADMIN MANUAL
1. Registration
Upon purchase of the iStorage Remote Management Console license, you will receive an email containing
a ‘Registration link’ and ‘License Key’ to begin the registration process as described below.
Open the following link to take you to the registration page
and complete the registration fields as set out below.
https://rm.bt.istorage-uk.com/Account/Register
1. License Key: Refer to the registration email from
iStorage that contains your License Key.
2. Admin Username: This must be an email
address which will be used for Admin sign-in.
3. Password: Create a secure password.
4. Confirm Password: Re-enter your password to confirm.
5. Select your Country from the drop down menu and then
Enter your mobile phone number: This is required for
‘Two Factor Authentication’.
6. Click ‘Register’.
7. On the ‘Enable two-step verification’ page, enter the
6-digit code received by text message and click Next.
8. Click ‘Done’.

#7
www.istorage-uk.com
iStorage datAshur®BT ADMIN MANUAL v 1.7
ADMIN MANUAL
2. How to enroll as an Administrator (Admin)
The Administrator is able to provision, set security policies and have full control and visibility of all datAshur BT Managed
Drives deployed throughout an organisation by using the iStorage web based Remote Management Console.
To setup as Admin, you will need your Username and Password you created during the registration process as described
in ‘section 1 - Registration’ and then proceed with the following steps.
1. Download and install the datAshur BT Admin App from the Apple App
Store or Google Play, or scan the QR code directly from your smartphone
to download.
2. In the pop message, tap Allow.
3. Enter your Username and Password and then tap on
Login to RM (Remote Management) Account.
Note: Your Username and Password for both the datAshur BT Admin App and the
iStorage web based Remote Management Console are the same.
After successfully logging in, the Drive Settings menu will open ready for setting
security policies and provisioning all datAshur BT Managed Drives as described in
the following section.
datAshur BT Admin App

#8
iStorage datAshur® BT ADMIN MANUAL v 1.7
www.istorage-uk.com
ADMIN MANUAL
3. How to Provision datAshur BT Managed Drives
1. Open your datAshur BT Admin App and enter your Username and
Password and then tap on Login to RM (Remote Management) Account.
2. After successfully logging in, the Drive Settings menu will open ready for you to review and apply your security
settings as described below:
•RM Enforced: This is switched on by default (GREEN light on) and MUST
remain ON to enable Remote Management provisioning. When switched off,
a Drive can be provisioned to work with the non-managed App (datAshur BT
App - refer to a separate user manual).
•User Password: The datAshur BT ships with a default password
(11223344). To change the default password, tap on ‘User Password’ and
then enter and confirm your New 7-15 character Password and finally tap
on ‘Set User Password’.
Password Requirement: Password must be 7-15 characters in length and
cannot contain only consecutive or repetitive numbers or letters.
Note: For security reasons, we strongly recommend that each user change
the default or Admin set password to their own unique 7-15 character
password once the Drive has been issued to them.
•Inactivity AutoLock: To protect against unauthorised access if the Drive
is unlocked and unattended, the datAshur BT can be set to automatically lock
after a pre-set amount of time. In its default state, the datAshur BT
Unattended Inactivity AutoLock feature is turned off (Never) but can be set to
autolock between 1 - 60 minutes.
To set a time limit, tap on Inactivity AutoLock and then tap to choose your
desired length of time.
Note: When Admin sets the Inactivity AutoLock, the User is prohibited from
disabling this feature.
After setting up as Admin (section 2), you will first need to provision all datAshur BT Managed Drives you intend to
manage via the Remote Management Console one Drive at a time.
To start provisioning, proceed with the following steps.

#9
www.istorage-uk.com
iStorage datAshur®BT ADMIN MANUAL v 1.7
ADMIN MANUAL
•Step-away AutoLock: The Step-away AutoLock is switched off by default,
if enabled (GREEN light on), this will set all the deployed datAshur BT
Managed Drives to lock when a user’s Smartphone (Android/iOS) is moved
approximately 5 meters away from the datAshur BT Drive for more than 5
seconds.
Note: When Admin enables Step-away AutoLock, the User is prohibited
from disabling this feature.
•Set Read Only: The Read Only feature is switched off by default, when
enabled (GREEN light on), all deployed datAshur BT Managed Drives will
be set as Read Only/Write Protect.
Note: When Admin enables Read Only, the User is prohibited from disabling
this feature.
•Remember Password: The Remember Password feature is operational
(ON) by default, enabling Users to set their Drives to unlock without entering
their password. To disable this feature (recommended) and prohibit Users
from setting their Drives to unlock without entering a password, tap on the
greyed out switch to prohibit (RED light on).
Note: When Admin prohibits Remember Password (RED light on), the
User cannot enable this feature and will need to enter their password each
time they need to unlock their Drive.
•Biometric Unlock: The Biometric Unlock feature is operational (ON) by
default, enabling Users to set a Biometric Unlock to access their Drives. To
disable this feature and prohibit Users from setting a Biometric Unlock to
access their Drives, tap on the greyed out switch to prohibit (RED light on).
Note: When Admin prohibits Biometric Unlock (RED light on), the User
cannot enable this feature.
3. Tap to Confirm your Drive Settings.
4. Tap Continue to provision all datAshur BT Managed Drives with your preferred
settings.

#10
iStorage datAshur® BT ADMIN MANUAL v 1.7
www.istorage-uk.com
ADMIN MANUAL
5. Make a note of the Device ID number printed on the USB connector and
connect the datAshur BT Managed Drive to a powered USB port.
6. Tap on the RED padlock.
Note: The Drive LED will be blinking RED.
7. Enter the Device ID number and then tap OK.
8. Tap on the GREY (Blank) padlock to finish provisioning.
9. Once provisioning is complete, the App will display a GREEN checkmark
and the Drive LED will be solid Blue, indicating that the datAshur BT
Managed Drive has been provisioned and will be automatically detected by your
Remote Management Console and ready to be assigned to a user.
Note: If provisioning multiple Drives that are connected to a multi-port USB hub,
repeat steps 6-9 for each and every Drive, one Drive at a time.
10. You will now be prompted by your computer to format all provisioned datAshur BT Managed Drives. Refer to
section 12 ‘Formatting the datAshur BT for Windows’ or section 13 ‘Formatting the datAshur BT for mac OS’.
Note: Once formatted, Admin is able to access the Drive and add data if necessary.

#11
www.istorage-uk.com
iStorage datAshur®BT ADMIN MANUAL v 1.7
ADMIN MANUAL
4. How to Create Users via the Remote Management Console
1. Click on the following link to open the Remote Management Console,
https://rm.bt.istorage-uk.com/Account/Login
2. Sign in using your Admin Username and Password.
3. After successfully signing in, the datAshur BT
Remote Management Dashboard will open.
4. To add users, under ‘Create User’, type in the Name and Email Address of the
intended user and click on Create to send an email to the recipient containing
their username and temporary password and a download link for the datAshur BT
Managed App. All users that are created will appear on the Users Dashboard.
To create and import a list of users, do the following:
• In an excel spreadsheet, enter the name of each user followed by a semi-colon (;)
before the email address. For example:
‘User One;user[email protected]’
‘User Two;user[email protected]’
• Save your spreadsheet as a ‘.CSV’ file.
• Click on ‘Import’.
• In the ‘Import Users’ dialog, click on ‘Choose a file’, navigate to your file and
then click ‘Import’.
• All the imported users will appear listed on the Users Dashboard.
Note: For detailed instructions on how to use the datAshur BT Managed App, please
refer to the datAshur BT Managed User Manual.

#12
iStorage datAshur® BT ADMIN MANUAL v 1.7
www.istorage-uk.com
ADMIN MANUAL
1. Sign in to the Remote Management Console.
2. In the ‘Users’ tab under ‘Users Dashboard’
click on the User Name. For example ‘User
One’.
3. Select a Drive from the dropdown menu under ‘Add Drive’ to assign to
the User then click on ‘Add’ and finally click ‘Save’.
The Drive, identified by the serial number will be assigned to the User
and enabled. The example provided in the image bottom right shows that
the ‘Drive S/N’ ending in 02 has been assigned to User One.
Note: To assign additional Drives to users, repeat steps 2 and 3.
You can also assign multiple Drives to one User.
5. How to Assign Drives to Users

#13
www.istorage-uk.com
iStorage datAshur®BT ADMIN MANUAL v 1.7
ADMIN MANUAL
6. Managing Users Dashboard
Once all the datAshur BT Managed Drives have been assigned to users, Admin will now be able to perform the
following actions from the Users Dashboard.
Enable or Disable User Access.
Delete User from system & Reset the Users App password.
Search for Users.
Click on a user name to open Geo & Time-Fencing and Allowed Drives panel.
How to Enable or Disable User Access
1. To Disable (prohibit) a User access to the datAshur BT
Managed Drive, uncheck the Check box under ‘Enable’ to
clear the check mark and click Save to disable access for the
user.
Note: To enable user access, click the Check box to restore the
checkmark and click Save.
How to Delete a User from Remote Management
2. To delete a User from Remote Management, click on the
menu field under More, then click Delete User and
in the ‘Delete Confirmation’ dialog, click Delete.
Note: To add the User back to Remote Management, refer to
section 4 - How to Create Users via the Remote
Management Console.
How to Reset User’s datAshur BT Managed App Password
3. To reset a User’s datAshur BT Managed App Password, click
on the menu field under More, then click Reset
User’s App Password and then in the ‘Reset
Confirmation’ dialog, click Reset.
Note: Resetting the App password will not affect, nor change the
Drive Password (default: 11223344).
When the App password has been reset, the user will receive an
automated email containing a temporary password.
 


Users Dashboard at a glance

#14
iStorage datAshur® BT ADMIN MANUAL v 1.7
www.istorage-uk.com
ADMIN MANUAL
Search Bar
4. To search for a User, enter either the User’s name or email
address in the search bar and click on the magnifying glass.
Opening the Geo & Time-Fencing Panel
5. By clicking on a User name, you will open
and be able to manage Geo-Fencing and
Time-Fencing restrictions. Refer to section
8 ‘How to Apply Geo & Time-Fencing
Restrictions’.
7. Managing Drives Dashboard
Click on ‘Drives’ top right corner of screen to open the ‘Drives Dashboard’ where Admin will be able to perform the
following actions.
How to Delete a Drive from Remote Management.
Search by Drive Serial Number.
Click on a Drive Serial Number to open and Manage Access Control.



Note: The checkmark under ‘ACTIVE’ indicates that the Drive is active and managed by Remote Management.
Drives Dashboard at first glance

#15
www.istorage-uk.com
iStorage datAshur®BT ADMIN MANUAL v 1.7
ADMIN MANUAL
#15 www.istorage-uk.com
How to Delete a Drive from Remote Management
1. To delete a Drive from Remote Management, click on the
menu field under More, then click Delete Drive and
in the ‘Delete Confirmation’ dialog referencing the
Drive Serial Number to be deleted, click Delete.
Note: To add the Drive back to Remote Management, refer to
section 3 - How to Provision datAshur BT Managed
Drives.
Search by Drive Serial Number
2. To search for a Drive, enter the Drive Serial Number in the
search bar and click on the magnifying glass.
Managing Access Control
3. By clicking on a Drive Serial Number (S/N), you will be
able to access the Drive and manage the following actions
remotely:
Enable or Disable Drive Access.
How to Wipe a Drive via Remote Management.
How to Change a Drive Password via Remote
Management.
How to Unlock a Drive via Remote Management.
Viewing Assigned to & Access Log.

,&

Enable or Disable Drive Access
4. To Disable (prohibit) a User access to the datAshur
BT Managed Drive, uncheck the Check box under
‘Enable’ to clear the check mark and disable Drive access
for the user.
Note: To enable user access, click the Check box to restore the
checkmark.

#16
iStorage datAshur® BT ADMIN MANUAL v 1.7
www.istorage-uk.com
ADMIN MANUAL
How to Wipe a Drive via Remote Management
6. Click on the drop down menu under Drive operation and
then select ‘Admin Remote Wipe’ (Reset) and click
‘Save’. A ‘Drive changes have been saved’
confirmation message will be displayed.
Note: Once ‘Admin Remote Wipe’ has been activated, a check
mark will be displayed under ‘ADMIN REMOTE WIPE’ in
‘Drives Dashboard’, indicating that ‘Remote Wipe’ is pending
and will be activated the next time the datAshur BT Managed Drive
is connected to the datAshur Managed App.
The check mark will clear (unchecked) as soon as the Drive is
connected to a computer, indicating the Drive has been remotely
wiped (reset).
How to Change a Drive Password via Remote Management
7. Click on the drop down menu under Drive operation
then select ‘Change Drive Password’ and then enter the
New Password in the Drive’s User Password field
and click ‘Save’. A ‘Drive changes have been
saved’ confirmation message will be displayed.
Note: Once ‘Change Drive Password’ has been activated, a check
mark will be displayed under ‘CHANGE DRIVE PASSWORD’
in ‘Drives Dashboard’, indicating that action is pending and
that the next time the datAshur BT Managed Drive is connected to
the datAshur Managed App, the New Password will be required to
unlock the Drive.
The check mark will clear (unchecked) as soon as the Drive is
connected to a computer and unlocked using the New Password.
How to Unlock a Drive via Remote Management
8. Click on the drop down menu under Drive operation and
then select ‘Admin Remote Unlock’ and click ‘Save’.
A ‘Drive changes have been saved’
confirmation message will be displayed.
Note: Once ‘Admin Remote Unlock’ has been activated, a check
mark will be displayed under ‘ADMIN REMOTE UNLOCK’ in
‘Drives Dashboard’, indicating that action is pending and that
the next time the datAshur BT Managed Drive is connected to a
computer the Drive will be unlocked without entering the Drive
User Password. This is a ‘One-Time’ action only.
The check mark will clear (unchecked) as soon as the Drive is
connected to a computer and remotely unlocked.

#17
www.istorage-uk.com
iStorage datAshur®BT ADMIN MANUAL v 1.7
ADMIN MANUAL
#17
Viewing Assigned to & Access Log
Assigned to
9. The ‘Assigned to’ tab contains the name of the User the
Drive has been assigned to, or names of Users if the Drive is
assigned to more than one user.
Access Log
The ‘Access Log’ contains the following information:
Date and Time of when the User accessed the Drive.
User’s email address.
Type of operation performed, i.e, ‘Unlock’ / ‘Reset’ etc.
Details of Drive access
Click on the ‘Map’ icon to view the location of
where the Drive was last accessed.
Search by ‘Type of operation performed’ to filter.
   

8. How to Apply Geo & Time-Fencing Restrictions
Allowed Drives - Enable/Disable or Delete Drive
Allowed Time - Time-Fencing
Allowed Location - Geo-Fencing
Geo & Time-Fencing at first glance




#18
iStorage datAshur® BT ADMIN MANUAL v 1.7
www.istorage-uk.com
ADMIN MANUAL
#18 www.istorage-uk.com
Allowed Drives
1. To Disable (prohibit) a User access to the datAshur BT
Managed Drive, click the Check box (1) under ‘Enable’ to
clear the check mark and click Save to disable access for the
User.
Note: To enable User access, click the Check box to restore the
check mark and click Save.
2. To delete a Drive from Remote Management, click on the
menu field (2), then click Delete Drive and
in the ‘Delete Confirmation’ dialog referencing the
Drive Serial Number to be deleted, click Delete.
Note: To add the Drive back to Remote Management, refer to
section 3 - How to Provision datAshur BT Managed
Drives.
How to set Time-Fencing Restrictions
Time-Fencing can be applied to any individual User
restricting the use of a Drive to within a specific time frame,
for instance between, ‘From 09:00’ - ‘To 17:00’ only.
1. To Set Time-Fencing, click in the ‘From’ field and either
select the time, or type in manually and do the same with the
‘To’ field. Then select your ‘Time Zone’ from the drop down
menu and click Save. A ‘User data is saved’ message will
be displayed as confirmation.
Note: To clear your time selection, click on the ‘From’ and ‘To’
fields and delete the entries, then click Save.
How to set Geo-Fencing Restrictions
A User’s access can be restricted by setting the ‘Allowed
Location’ as follows:
1. Region: User access can be set by ‘Region’, for instance
‘Europe’.
2. Country: First select the ‘Region’ and then select the
‘Country’ from the drop down menu.
3. Address: Complete the ‘Address’ field including Zip/Postal
Code to restrict User access to that Address only.
4. City: Enter a name of a ‘City’, for instance London.
5. State/Province: Restrict User access to a specific State or
Province.
6. Zip/Postal Code: Restrict User Access to a specific
Zip/Postal Code.
7. Radius: To expand the ‘Allowed Location’ radius, enter a
value under Radius and then choose either ‘Miles or Km’.
8. Click ‘Save’ to apply your restrictions or click ‘Clear’ to
remove all values.
 

#19
www.istorage-uk.com
iStorage datAshur®BT ADMIN MANUAL v 1.7
ADMIN MANUAL
#19 www.istorage-uk.com
9. How to Change the Admin Password
To change the Admin Password, do the following:
1. Click on the ‘Admin’s email address’.
2. Enter your ‘Current Password’ followed by your
‘New Password’ then ‘Confirm New Password’ and
finally click ‘Change Password’.
Note: Changing the Admin Password for the Remote
Management Console will automatically update and change
the Password for the datAshur BT Admin App to be the same.
Remember the Admin Password is the same for both, the
Remote Management Console and the datAshur BT
Admin App.
10. Account Summary
To access and view your Account information, do the following:
1. Click on the name of the account next to
‘Account Summary’ and then navigate through the
following tabs:
• Summary: View information relating to your valid
License including the number of Admin’s, User’s and
Drives.
• Admin Contacts: View details of all enrolled Admin’s,
including email addresses, mobile numbers and date and
time of Admin’s last login.
• User Contacts: View the User names, email addresses
and date and time of User’s last login.
• Drives Activity: View list of all Serial Numbers, when
they were provisioned and by whom, last login attempt
and User’s email addresses.

#20
iStorage datAshur® BT ADMIN MANUAL v 1.7
www.istorage-uk.com
ADMIN MANUAL
11. How to Provision a Non-Managed Drive
1. Open your datAshur BT Admin App and enter your Username and
Password and then tap on Login to RM (Remote Management) Account.
Note: Your Username and Password for both the datAshur BT Admin App and the
iStorage web based Remote Management Console are the same.
2. After successfully logging in, the Drive Settings menu will open ready for you to review and apply your security
settings as described below:
•RM Enforced: Switch the GREEN light OFF. Remote Management
disabled.
•User Password: The datAshur BT ships with a default password
(11223344). To change the default password, tap on ‘User Password’ and
then enter and confirm your New 7-15 character Password and finally tap
on ‘Set User Password’.
Password Requirement: Password must be 7-15 characters in length and
cannot contain only consecutive or repetitive numbers or letters.
Note: For security reasons, we strongly recommend that each user change
the default or Admin set password to their own unique 7-15 character
password once the Drive has been issued to them.
•Inactivity AutoLock: To protect against unauthorised access if the Drive
is unlocked and unattended, the datAshur BT can be set to automatically lock
after a pre-set amount of time. In its default state, the datAshur BT
Unattended Inactivity AutoLock feature is turned off (Never) but can be set to
autolock between 1 - 60 minutes.
To set a time limit, tap on Inactivity AutoLock and then tap to choose your
desired length of time.
Note: When Admin sets the Inactivity AutoLock, the User is prohibited from
disabling this feature.
You are able to provision a previously used ‘Managed’ Drive into a stand-alone ‘Non-Managed’ Drive that will only work
with the datAshur BT Personal App available to download on the Apple App Store and Google Play.
To start provisioning and set the security parameters as a non-managed Drive, proceed with the following steps.