Jabra GN9330e - USB - Headset User manual

Jabra Link 14201-10
How to connect my Jabra GN9330e with Aastra 6753i, 6755i,
6757i
Prerequisite:
Jabra GN9330e + Jabra LINK 14201-10 + Aastra DHSG Cable Kit (only
available from Aastra)
In combination with one of the following phones:
Aastra 53i / 55i / 57i / 57iCT
Aastra 6753i / 6755i / 6757i / 6757i CT
From phone firmware 2.5.1.2000 or higher.
Connection:
Important: Please note that remote call control for the Jabra GN9330e is
supported from version "L" or the Date code 9/09.
Aastra DHSG cable:
1. Insert the split end of the Aastra DHSG cable into your phone as
23/11/2022 14:54
https://www.jabra.in/supportpages/jabra-link-14201-10/14201-10/faq/f698f087-85fd-492f-
9aea-affbf082d1dd
Page 1 of 4

follows. The RJ9 plug (marked green) into the "headset" socket and the
RJ45 plug (marked yellow) into the socket for the expansion module/
expansion modules.
2. Plug the 1-sided end of the Aastra DHSG cable marked in blue into the
RJ45 adapter.
GN Netcom DHSG cable:
1. Now plug the 1-sided of the GN Netcom DHSG cable marked in blue
into the free socket of the RJ45 adapter.
2. Insert the RJ9 plug into the socket marked with a “phone" symbol and
the RJ45 plug into the base socket of the Jabra GN9330e marked with
"AUX".
Software setup:
Put the headset into the base and activate the "DHSG" mode.
Hold down the "phone" button on the base of the Jabra GN9330e for
approx. 6 seconds until the online display (blue LED) on the headset starts
to flash. The current software is displayed to you by activating the volume
controller in the form of the charge display (green LED).
23/11/2022 14:54
https://www.jabra.in/supportpages/jabra-link-14201-10/14201-10/faq/f698f087-85fd-492f-
9aea-affbf082d1dd
Page 2 of 4

LEDs from left to right:
LED 1 = RHL
LED 2 = DHSG
LED 3 = AEI
LED 4 = MSH
Now you can switch between the different software modes (LED 1-4) by
using the "volume" up/down controller on the headset. To confirm the
software has successfully installed, the base automatically switches back
to charge mode after approx. 15 seconds.
Base setup:
Set the phone set-up switch to "A".
Phone setup:
In version 2.5.1.2000 the DHSG mode is disabled by default and must be
activated via the Aastra.cfg or mac.cfg with the command dhsg:1.
From version 2.5.2 Options> Preferences> Audio Settings> DHSG > On
The audio mode must be set to "Headset/Speaker" in the phone settings:
Options > Preferences > Audio Settings > Audio Mode > Headset/Speaker.
Remote call control in combination with an expansion keypad is not
supported!
23/11/2022 14:54
https://www.jabra.in/supportpages/jabra-link-14201-10/14201-10/faq/f698f087-85fd-492f-
9aea-affbf082d1dd
Page 3 of 4

Headset answer/end:
As soon as the dial tone signal can be heard in the headset, you can answer
the call by pressing the "answer/end" button on the headset; by pressing
again the call is ended.
23/11/2022 14:54
https://www.jabra.in/supportpages/jabra-link-14201-10/14201-10/faq/f698f087-85fd-492f-
9aea-affbf082d1dd
Page 4 of 4