Jabra GN9350e Safety guide

Jabra GN9350e
How to connect my Jabra GN9350e with Alcatel Touch 4029,
4039
Prerequisite :
Jabra GN 9350 + Jabra Link 14201-09
In combination with one of the following phones:
IP Touch 4029
IP Touch 4039
Connection:
2-sided end:
Insert the RJ45 plug into the socket marked with "AUX" and the RJ10 plug
into the base socket of the Jabra GN9350 marked with the “phone”
symbol.
2-fold Y-coupling end:
Insert the 3.5 mm audio jack into the headset interface and the RJ12 plug
into the bell socket of the phone. Now insert the phone's phone cable
directly into the additional connector socket of the Y cable.
12/02/2023 06:15
https://www.jabra.com/supportpages/jabra-gn9350e/9326-607-405/faq/307c489b-8b15-
4dd3-be2b-4d6ff48bc1c1
Page 1 of 4

Software setup:
In the LCD display, set the Jabra GN9350 to "MSH" and press the OK
button.
Base setup:
Set the phone setup switch (A-G) to the "A" position.
Microphone level setup:
We recommend setting the microphone volume in the LCD display to 7
out of 12.
Headset answer/end:
12/02/2023 06:15
https://www.jabra.com/supportpages/jabra-gn9350e/9326-607-405/faq/307c489b-8b15-
4dd3-be2b-4d6ff48bc1c1
Page 2 of 4

As soon as the dial tone signal can be heard in the headset, you can answer
the call by pressing the ”answer/end” button on the headset; by pressing
again the call is ended.
Phone setup:
For system software version 9.xx and higher:
No settings are required on the phone for the use of a headset. Following
the correct adaptation of the audio jack, a headset symbol should appear
in the “Phone display”. If the headset symbol does not appear, please
check the following settings:
Menu> Settings> Phone> Audio Jack> Select/ Activate Headset.
Phone setup with system software version below version 9.xx:
Important: The “Force Headset” function must not be activated on the
phone, as otherwise it will not be possible to accept external calls!
Menu> Settings> Phone> Audio Jack> Force Headset OFF
Menu> Settings> Phone> Socket > Activate Headset
Dial tone signal transfer/ phone setup:
Important: The dial tone signal in the headset is only transmitted if one of
12/02/2023 06:15
https://www.jabra.com/supportpages/jabra-gn9350e/9326-607-405/faq/307c489b-8b15-
4dd3-be2b-4d6ff48bc1c1
Page 3 of 4

the following ringtones is used, e.g., Standard / Classic / Cold River /
Dooing-Dooing. > Menu> Settings> Dial Tone > Internal / External
Should the dial tone signal transfer not work although you have setup the
correct ringtone, please check the following settings:
Menu > Settings > Phone > Internal/External, More Options
No sound, Progressive, Beeps> all points must be set to "OFF".
Calls being made via the headset can be connected / forwarded as follows:
Dial the phone number > "Forward" will now appear in the phone display >
now press on to the appropriate function key next to the phone display >
thereafter you must end the call with the button marked "Handset".
12/02/2023 06:15
https://www.jabra.com/supportpages/jabra-gn9350e/9326-607-405/faq/307c489b-8b15-
4dd3-be2b-4d6ff48bc1c1
Page 4 of 4