JABSCO 23230-2012 User manual

MODELS:
23230-2012 12 Volts DC
23230-2024 24 Volts DC
GEAR PUPPY
FEATURES:
Medium duty pumps for general purpose
use.
lISO 8846 MARINE (Ignition protection)
lMaximum viscosity 150Cs
lInlet filter included
lSimple design means fewer wearing
parts
l24.5 lpm (6.5 US gpm) output @ 5m (16.4ft)
head
lSelf priming to 1.0m (3 ft)
lIdeal for water, oil and diesel transfer
INSTALLATION INSTRUCTIONS:
Jabsco Gear Puppy can be mounted on any flat
surface. Fit the pump in a dry, well ventilated
position. If installed in a vertical position the motor
must be above the pump head. Use the rubber
grommets provided to minimise vibration, do not
overtighten the mounting screws.
Secure 16mm (5/8”) id hose direct to the discharge
ports using stainless steel hose clamps. Use spiral
reinforced hose (with a smooth internal bore) that will
not collapse under suction, or rigid or semi rigid
pipework systems. The pipework must be compatible
with the liquid being pumped. Pipe runs should be
kept as straight and short as possible, avoiding rising
and dipping over obstructions. Fit a filter on the inlet
to prevent debris from entering the pump.
WIRING INSTRUCTIONS
Make all electrical connections in dry locations,
connections in humid environments should be sealed
to prevent corrosion. Protect the circuit with a
correctly rated fuse or circuit breaker in the red
positive (+) lead as close as possible to the power
source. Connect the black motor wire to the negative
(-) battery terminal. Inadequate voltage at the motor
terminals when the pump is running (not less than
10% below rated voltage at full load) due to partially
discharged batteries or insufficient cable size may
result in blowing fuses, failure to start or poor pump
performance.
WARNING: If the fuse fails
repeatedly do not fit a heavier fuse or
bridge the fuse terminals with silver
paper or metal wire. Failure to observe
this instruction may result in a fire
hazard due to overheating of cables.
WARNING: All marine pumps
discharging overboard must be
installed with the overboard discharge
well above both static and heeled
waterlines.
m ft lpm US gpm
0 0 26 6.9
5 16.4 24.5 6.5
10 33 22.5 6.0
15 49 20 5.3
20 65 17 4.5
GEAR PUPPY PERFORMANCE
Approximate performance for new pump,
running water at 20°C with fully charged battery
TOTAL HEAD
GEAR PUPPY
WARNING: Do not use any Jabsco
pump for petrol, petroleum products or
any products with a flash point below
37°C (98°F), explosion or death may
occur.

PART
NUMBERS
VOLTAGE
MAXIMUM
AMP
DRAW
MAXIMUM
FUSE
SIZE
MINIMUM WIRE
SIZE
MAXIMUM LENGTH
BETWEEN (+) & (-)
BATTERY TERMINALS
23230-2012 12 volt 12 amp 15 amp
30 / 0.25mm
(1.5mm²)
4.5m (15ft) *
23230-2024 24 volt 5 amp 7.5 amp
32 / 0.2mm
(1.0mm²)
4.5m (15ft) *
Electrical Wiring Information
DIMENSIONAL DRAWING
WEIGHT: Gear Puppy - 2.2kg (4.8lb)
Warranty: All products of the company are sold and all services of the company are offered subject to the company’s warranty and terms and conditions of sale, copies of which will be furnished upon request.
©Copyright 2003 ITT Industries
Jabsco
ITT Industries
Jabsco, 1 Kondelin Road, Cape Ann Industrial Park, Gloucester, MA 01930
Tel : [phone] Fax : [phone]
Jabsco, Bingley Road, Hoddesdon, Hertfordshire, EN11 0BU
Tel : [phone] Fax : [phone]
Fluid Products Canada,55 Royal Road, Guelph, Ontario N1H 1T1
Tel : [phone] Fax : [phone]
NHK Jabsco Co Ltd,3-21-10, Shin - Yokohama, Kohoku-ku, Yokohama 222
Tel : [phone] Fax : [phone]
Jabsco GmbH,Oststraße 28, 22844 Norderstedt
Tel : [phone] Fax : [phone]
USA
UK
CANADA
JAPAN
GERMANY
Discover Jabsco at www.jabsco.com
* For longer installations, fit thicker cables
All dimensions are in mm
Rev 10/03 43000-0796