Janssens Victorian Vi-34 User manual

Victorian Vi-23, 34, 36
Version 2016_1.1
VICTORIAN ASSEMBLY INSTRUCTIONS

PRODUCT INFORMATION
Dear customer,
Thank you for buying a high-quality aluminium greenhouse.
REMARKS
The drawings in these instructions are for all basic models.
However, this manual should be sufficient to guide you
through the assembly of all sizes and variations of this
greenhouse. This greenhouse is designed for the cultivation
of plants/flowers. Therefore leakage, water drops and
condensation inside the greenhouse are allowed and to be
expected. The greenhouse should only be entered by
competent persons during cultivation or maintenance.
Aluminum profiles that are not painted may show black
stains, these stains are not a production error: they can be
easily removed with an aluminum cleaner available at every
good drugstore. The rubber strips have been treated with
oil/silicone to ease assembly. The greenhouse can be
mounted on a solid concrete foundation or on a solid
packed surface with concrete anchors in the corners. The
solid concrete foundation should be deep enough to get a
solid and frost-free ground. The greenhouse should be
anchored securely and the anchors should be checked
periodically. During winter it is necessary to clear the roof
of snow. The greenhouse should be built in a location
protected from strong winds. Protective gear (such as
protective gloves) should be used during the assembly in
order to avoid injuries. One should pay attention at all times
and consult the local building regulations.
ASSEMBLY ORDER
The assembly procedure is the same for all of
our greenhouses.
- Sort the profiles according the model.
- Assemble the aluminium framing.
- Level the framed greenhouse using a waterlevel.
- Securethe greenhouse to the ground
- Install glass.
REQUIRED TOOLS
10mm Socket Wrench
10mm Spanner Wrench
Water-level
Phillips screwdriver
Powered Drill + 4.2mm or 11/64ths Drill Bit
Scissors (to cut the rubber).
We reserve the right to change the construction without
prior notice!

Top Shelf
Top/Bottom profile of sliding door
Curtain Rail
Side Profile Turning Door
Horizontal Profile
Turning Door
Side profile Turning Door
Hanger for Sliding Door
Vertical Glazing Bar
Gable Profile
Bottom guide for sliding door Rubber Gasket
Roof Glass Support pieces

Vi23
2360 mm/ 92.91 in
Vi34
3100 mm/ 122.04 in
Vi36
3100 mm/ 122.04 in
Vi23
3100 mm/ 122.04 in
Vi34
4580 mm/ 180.31 in
Vi36
6050 mm/ 238.19 in
Note: Do not set concrete in the corners until
the entire greenhouse frame is complete.
You may need some play to install the
uprights.
Royal Victorian

Note: Divide millimeters by 25.4 to get inches
This pages applies when you
have a dropped door kit.

Note: When assembling the foundation in this step
only hand-tighten the nuts. The corners may need
to be slightly loose to attach the corner uprights
Note: Before assembling the foundation insert 3
M6x15 bolts as shown for the sliding door
guide.
See page S1.
Suggestion: If the unit is to be installed
on a concrete foundation you will need
to cut PRO210 flush with the bottom of
PRO6120.
You can lay the cut off PRO210 peices
on their side and use them to secure the
PRO6120 to the concrete foundation.

Insert a bolt into
each upright on the
side where the top
shelf will be located.
Insert a bolt in corner
of front and back wall
for Seed Tray. See
page ZB2 and SC1

--------------
Suggestion: Now is a good time to install
the L1 corner wind braces shown on
page H10.
------------------------------------
-------------------------------------
Note: If you have purchased shade curtains, insert the slider loops into the gutter profile
before this assembly step. This is shown below.
1-Twist lock
per end
28 Slider loops per curtain

Insert a bolt in each upright on the
side where the top shelf will be
located. Refer to page ZB2 and SC1
Note: Add three bolts to each
PRO1456 profile here for thePR
louvre window. See page LR1
-----------------
------------
Note: A bolt needs to be added for the
Seed Tray support. See page ZB1.
Vi34: Add one bolt in the center
PRO1456 upright post
Vi36/Vi46: Add one bolt in every other
PRO1456 upright post
----------------------------
Note: Use PRO29909
for the door frame.
See pages S1 and A1
Note: Sliding door can
be placed in any
section except the
corner sections.
Note: Louvre window can
be placed in any section.

________
Total amount of bolts to be
inserted in roof beam center
track at this point:
2 for L brackets - Pg H7
2 for roof supports - Pg H9
3 for misting system -Pg H14
---------------
Insert bolts to connect short
uprights to the PRO6918.
You will need as many bolts
as you have short uprights.
_______
_______
Use the longer supplied
bolts in this location. They will ease the
installation of the curtains and cross supports

Note: Now is a good time to install the roof
braces. Refer to page H10.
Note: If you have purchased curtains
now is a good time to install the
curtain rails.
Refer to page SD1
Note: Add one bolt
per end for the roof
support tube.
See page H9
Vi 23 Vi34/36

Note: Roof window can be installed in any bay.
Note: When installing the roof uprights, make note of which bays will
have roof windows and insert a bolt for the connection plate.

Note: Ends of support tube will need to be bent to fit.
Attach the lower end and adjust the top until it fits
flush.

Drill a hole and attach wind brace to the roof profile with short screw or bolt
Note: Wait until assembly is complete before attaching the roof braces
to the roof uprights.

Note: On units longer than 16ft
additional roof supports have been
supplied.
Install the supports as shown as close
to the center as possible. Do not
tighten the bolts.
Lift the roof beam up 1/2 inch and
then tighten all of the bolts for the
supports.
Additional Roof Support for models over 16ft

------
Note: The gutter down pipe is attached to
the base of the greenhouse with a screw
that goes through the back of the elbow.
First, drill a small hole in the back of the
elbow and then a small hole in the frame
of the greenhouse for the screw to thread
into. Run the screw through the hole on
the inside of the elbow and into the
greenhouse base.
Note: Use a small slef-
tapping screw to attach the
plastic gutter down spout
to the gutter profile and
also the down pipe to the
plastic downspout (Shown
below)

Note: Glass supports slide in from the end of the gutter profile
to support the bottom of the glass. The supports should be
spaced 100mm or 4 inches from each roof profile.
Roof Glass Support Installation
H 14