Janus PAD100-SB User manual

DS1348 Revised: 20-Aug-2019
The Addressable Sounder Base 6” (PAD100-SB) is a sounder base that may be utilized in a variety of
applications. The base has a locking feature for the sensor that may be used or removed in the eld.
Once the head is removed, the sounder is accessible in the bottom of the unit.
The base has an independent sounder module that may be programmed as a single station, zone or
all call sounder. The PAD100-SB passes through the sound pattern sent to the sounder, therefore it
may reproduce in any pattern the power supply provides.
The panel will support any combination of sensors or modules on the SLC. The PAD100-SB does not
consume an address on the loop and is fully programmable to operate with any input. Once activated
the sounder will also follow the input from the power source and deactivate accordingly.
PAD100-SB
Addressable Sounder Base
© 2017 Janus Fire Systems. All rights reserved (5/2017) Janus Fire Systems® is a registered trademark of Janus Fire Systems.
• Integrated Sounder in base
• 75 dB (UL 464 Listed) sounder output
• Sounder independent of sensor, allows for a single
station, grouped or all-call
• May be mapped to any device connected to the
control panel
• Terminals accept 22 to 12 AWG wire sizes
• Supports Class A, Class X and Class B wiring
• Does not require SLC Loop address
• UUKL Listed for Smoke Control
Working Range for SLC: 24 VDC
Working voltage range for PWR: 16 - 33 VDC
Active current for PWR: 30 ma
Sound pressure level: 75dB/10ft (min.) as per UL464
Installation temperature range: 32°F to 120°F (0°C to 49°C)
Operating relative humidity range: 0% to 93% (Non-condensing)
Start-up time: Max. 1 sec.
Maximum number of devices per zone: 127
Color: Eggshell White
Height: 0.75 in (19 mm)
Diameter: 6.3 in (166 mm)
Features
Specications
Description
PAD100-SB should be mounted directly on the electrical box. The mounting holes are congured for
a single gang, double gang, octagon or 4” square box.
Detector Base Mounting
Using the two included
screws, attached the
detector base to detector
bracket.
Mount the detector
bracket to the back box
using the mounting
screws.
Alignment Features
P/N 97674

DS1348 Revised: 20-Aug-2019
1102 Rupcich Drive
Millennium Park
Crown Point, IN 46307
TEL: [phone] FAX: [phone]
e-mail: info@janusresystems.com
www.janusresystems.com
The seller makes no warranties, express or implied, including, but not limited to, the implied warranties of merchantability and
tness for a particular purpose, except as expressly stated in the seller’s sales contract or sales acknowledgment form. Every
attempt is made to keep our product information up-to-date and accurate. All specic applications cannot be covered, nor can
all requirements be anticipated. All specications are subject to change without notice.
Page 2 of 2
Note: Approvals/Listings maintained by and manufactured by Potter Electric Signal Company.
Ordering Information
Model Number Description P/N
PAD100-SB Addressable Sounder Base 97674
Break off tab (gray
area) in image to disable
locking feature.
Insert small screwdriver
into slot to remove
detector from base.
PAD100-SB include a locking feature that prevents removal of the detector and removal of the base
cover without using a tool.
1. To eliminate this feature, break off the locking tab and then install the detector.
2. To remove the detector from the base once the locking feature has been activated, insert a small
screwdriver into the slot on the base to push the plastic tab while simultaneously turning the detector
head counter-clockwise.
3. To remove the base cover from the lower enclosure once the locking feature has been activated,
insert a small screwdriver into the slot on the on the base to push the plastic tab while simultaneously
turning the detector head counter-clockwise.
Locking Feature